Advertisement
securely, stop using the product and keep it away from
children. If you think batteries might have been
swallowed or placed inside any part of the body, seek
immediate medical attention. CAUTION: Risk of
explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
ATTENTION: IL Y A RISQUE D'EXPLOSION SI LA BATTERIE
EST REMPLACÉE PAR UNE BATTERIE DE TYPE
INCORRECT. METTRE AU REBUT LES BATTERIES
USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
Improper replacement of the battery with an incorrect
type may defeat a safeguard (for example, in the case
of some lithium battery types). Do not dispose of the
battery into fire or a hot oven, or mechanically crush or
cut the battery, which may result in an explosion. Do
not leave the battery in an extremely high temperature
surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas. Do
not subject the battery to extremely low air pressure,
which may result in an explosion or the leakage of
flammable liquid or gas. + identifies the positive
terminal(s) of equipment which is used with, or
generates direct current. - identifies the negative
terminal(s) of equipment which is used with, or
generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles,
should be placed on the equipment. The serial port of
the equipment is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling the
parts. Wait one-half hour after
switching off before handling
parts. This sticker is to indicate
that the marked item can be hot
and should not be touched without taking care. For
device with this sticker, this device is intended for
installation in a restricted access location, access can
only be gained by service persons or by users who have
been instructed about the reasons for the restrictions
applied to the location and about any precautions that
shall be taken.
Installation
Install the equipment according to the instructions in
this manual. To prevent injury, this equipment must be
securely attached to the floor/wall in accordance with
the installation instructions. Never place the
equipment in an unstable location. The equipment may
fall, causing serious personal injury or death.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV):
The power source should meet limited power source or
PS2 requirements according to IEC 60950-1 or IEC
62368-1 standard.
Device powered by AC mains supply voltage: The
equipment must be connected to an earthed mains
socket-outlet. An appropriate readily accessible
disconnect device shall be incorporated external to the
equipment. An appropriate overcurrent protective
device shall be incorporated external to the equipment,
not exceeding the specification of the building. An
all-pole mains switch shall be incorporated in the
electrical installation of the building. Ensure correct
wiring of the terminals for connection to an AC mains
supply. The equipment has been designed, when
required, modified for connection to an IT power
distribution system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this
product. DO NOT stare at operating light source. May
be harmful to the eyes. Wear appropriate eye
protection or DO NOT turn on the white light when you
assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging while
transporting it.
System Security
The installer and user are responsible for password and
security configuration.
Maintenance
If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance. A few device
components (e.g., electrolytic capacitor) require
regular replacement. The average lifespan varies, so
periodic checking is recommended. Contact your dealer
for details.
Cleaning
Please use a soft and dry cloth when clean inside and
outside surfaces of the product cover. Do not use
alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may
burn out. DO NOT expose the device to high
electromagnetic radiation or dusty environments. For
indoor-only device, place it in a dry and well-ventilated
7
Advertisement
