Table of Contents
Advertisement
500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER
5. Check to make sure the chipper-shredder is on a level
surface that is not asphalt, concrete or harden ground. Block
the wheels and ensure support leg is secure to prevent
unintended movement of the chipper-shredder during
operation.
– Always operate the chipper shredder from the
manufacturer's indicated operator zone.
6. Fuel:
– Use an approved fuel container.
– Never add fuel to a running or hot engine.
– Fill fuel tank outdoors with extreme care. Never fill fuel tank
indoors.
– Replace gasoline cap securely and clean up any spilled fuel.
Operation
1. Before starting this chipper-shredder, review all safety rules.
Failure to follow these rules may result in serious injury to the
operator or bystanders.
2. Be sure to confirm all hose connections and hose clamps are
tight before each use. It is possible for connections to vibrate
loose over time.
3. Never leave the machine unattended with the power source
operating.
4. Never operate the machine when under the influence of
alcohol, drugs or medication.
5. The machine owner should instruct all operators in safe
chipper-shredder operation.
6. Always operate the chipper-shredder with all safety
equipment in place and all controls properly adjusted for safe
operation.
7. Always operate the chipper-shredder at manufacturer's
recommended speed.
8. Always keep hands and feet clear of moving parts.
9. When loading the chipper-shredder, never place your hands
inside or on the sides of the chutes, chambers, or intake.
Never place your hands or any part of your body between the
material and any part of the chipper-shredder.
– Never attempt to chip more than one (1) branch at a time,
this may cause the chute, chamber or intake to become
clogged.
– Never attempt to use your hand, foot or any body part to
unclog the chipper-shredder.
– Only attempt to unclog with a small diameter stick that can
get chipped.
iMPORTANT SAfETY iNSTRUcTiONS
– If a major clog occurs; turn the fuel valve off and let the
unit run until dry, turn off the engine, let the unit cool down,
unplug the spark plug wire and take apart the unit to see
where the clog has occurred. Remove clog before further
operation.
10. Only chip branches 3 in. (7.6 cm) or less in diameter.
11. Only shred bushes, shrubbery, leaves, etc. with branches
1/2 in. (1.3 cm) or less in diameter.
12. Only shred dry or slightly damp material. Never attempt to
shred material that is wet, as this may cause clogging to
occur.
13. Use only your hand to operate the chipper-shredder controls.
14. Do not refuel the engine until it has cooled for several
minutes.
Maintenance, Transport and Storage
1. Always shut off the power source and disconnect the spark
plug wire and ground the engine while repairing or adjusting
the unit.
2. Clean debris, shrubbery and chaff from the engine cylinder,
cylinder head fins, blower house rotation screen, and muffler
areas. If the engine is equipped with a spark arrestor muffler,
clean and inspect it regularly (follow manufacturer's service
instructions). Replace, if damaged.
3. Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an ignition
source (such as a furnace, water heater, etc.) and cause an
explosion. Fuel vapor is also toxic to humans and animals.
4. Clear debris from movable parts, but only when the engine is
off, the fuel valve is in the "OFF" position, and the spark plug
wire is disconnected.
5. Check to be sure all nuts and bolts are tight to assure the
equipment is in safe working condition.
6. Always use the shredder hopper handle and built-in wheels
to move the chipper shredder. Never lift the unit using the
fuel tank for support. If the unit must be lifted , always use at
least two people, and always grip the unit securely using the
front leg and shredder hopper handle.
7. Always follow the engine instructions for storage preparations
before storing the unit for both short and long term periods.
8. Always ensure that the fuel tank is empty before transporting
the unit in a vehicle.
9. Always transport the unit in the upright position on the
wheels and support leg.
7
Advertisement
Table of Contents
