1. Manuals
  2. Brands
  3. Champion Manuals
  4. Chippers/Shredders
  5. 500137-N
  6. Operator's manual

Champion 500137-N Operator's Manual

3 in. *7.6cm) chipper shredder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
MODEL #500137-N
3 iN. (7.6 cM) chiPPER ShREDDER
READ AND SAVE ThiS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
REV 20221122
Champion Power Equipment, Inc., Santa Fe Springs, CA USA

Advertisement

Table of Contents
loading

Summary of Contents for Champion 500137-N

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. REV 20221122 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...

  • Page 2: Table Of Contents

    TAbLE Of cONTENTS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER TAbLE Of cONTENTS Maintenance ..........Engine Maintenance ..........introduction ........... Chipper-Shredder Maintenance .........

  • Page 3: Introduction

    500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER iNTRODUcTiON SAfETY DEfiNiTiONS Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers.

  • Page 4: Important Safety Instructions

    SAfETY iNSTRUcTiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG  DANGER  Operation of this equipment may create sparks that can start fires around dry vegetation. Engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause A spark arrestor may be required.

  • Page 5: Fuel Safety

    SAfETY iNSTRUcTiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER fuel Safety WARNiNG  Keep Operator Work Zone Clear DANGER  Keep work zone clear of debris while working to ensure safe GaSolinE anD GaSolinE VaPorS arE hiGhlY footing.

  • Page 6: Training

    SAfETY iNSTRUcTiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER When operating the chipper-shredder: WARNiNG  – DO NOT move or tip the chipper-shredder during operation. Although the chipper shredder contains a spark arrester, – DO NOT tip the chipper-shredder or allow fuel or oil to spill.

  • Page 7: Operation

    SAfETY iNSTRUcTiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER 5. Check to make sure the chipper-shredder is on a level – If a major clog occurs; turn the fuel valve off and let the surface that is not asphalt, concrete or harden ground. Block...

  • Page 8: Safety And Dataplate Labels

    MANUFACTURE DATE XXXX DATE DE FABRICATION This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment. Colors...

  • Page 9: Operation Symbols

    2. Move the fuel valve to the “OPEN” position. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.

  • Page 10: Controls And Features

    AND fEATURES 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES Read this operator’s manual before operating your chipper-shredder. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

  • Page 11: Assembly

    ASSEMbLY 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY 2) install the handle 1. Insert handle (A) into the brackets on the lower shredder Your chipper-shredder requires some assembly. This unit ships chute. from our factory without oil. It must be properly serviced with fuel and oil before operation.

  • Page 12: Install The Chute Deflector

    ASSEMbLY 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER collection bag The collection bag can be attached and removed from the chute deflector using the adjustable drawstring. It is recommended to be attached before operation and removed before completely full, after operation, or before storage. The collection bag will collect up to 2 bushels (70 L) of material.

  • Page 13: Add Fuel

    ASSEMbLY 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER NOTicE  Weather will affect engine oil and engine performance. Change the type of engine oil used based on weather conditions to suit OIL DIP STICK the engine needs. Add fuel NOTicE ...

  • Page 14: Operation

    OPERATiON 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON cAUTiON  Use unleaded gasoline with a minimum octane rating of 91 chipper-Shredder Location and an ethanol content of 10% or less by volume. Never operate the chipper-shredder indoors or inside any confined DO NOT light cigarettes or smoke when filling the tank.

  • Page 15: Before Each Use Inspect The Chipper-Shredder

    OPERATiON 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER DANGER  DO NOT operate a damaged chipper-shredder, or one with damaged or loose parts. Operating a damaged unit or one with Up to Up to loose parts may cause damage to the product or injury to the 75 ft.

  • Page 16: Chipper-Shredder Operation

    OPERATiON 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER NOTicE DANGER   Pulling the recoil cord will spin the impeller and this will make If the impeller or blades strike a foreign object, stop engine noises. These noises are normal and should be made as the immediately.

  • Page 17: Clearing The Shredder Hopper

    OPERATiON 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER 7. Standing in the safe zone will prevent any damage or injury if 3. Disconnect the spark plug wire. a piece is kicked back out of the chipper chute. 4. Using your hands, remove the material that is still atop the shredder hopper.

  • Page 18: Operation At High Altitude

    MAiNTENANcE 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER NOTicE WARNiNG   If the engine will not be used for a period of two (2) weeks or Operation using the alternative main jet at elevations lower longer, please see the Storage section for proper engine and than the recommended minimum altitude can damage the fuel storage.

  • Page 19: Chipper-Shredder Maintenance

    MAiNTENANcE 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER 4. Remove oil fill cap/dipstick to add oil. Clean the air Filter 5. Add up to 37.2 fl. oz. (1100 ml) of oil and replace oil fill cap/ 1. Unscrew wing nut to remove the air filter cover.

  • Page 20: Flail Housing And Impeller Cleaning

    MAiNTENANcE 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER flail housing and impeller cleaning and impeller cleaning section should be followed to remove it and the shredder screen (A). (I) 1. Make sure spark plug wire is disconnected. 2. Disconnect the recoil housing on the front of the engine.

  • Page 21: Maintenance Schedule

    MAiNTENANcE 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Maintenance Schedule 8. To remove the shredder blade (H), unscrew both the M8x25 bolts (G), washers ø8 (K), lock washers ø8 (L) and M8 lock Follow the service intervals indicated in the following maintenance nuts (M).

  • Page 22: Storage

    STORAGE 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER STORAGE Engines Stored for Over 30 Days 1. Add a properly formulated fuel stabilizer to the tank. Refer to the maintenance sections for proper cleaning instructions. 2. Run the engine for a minimum of 3 minutes with treated fuel Always disconnect the spark plug wire in times of inactivity, to cycle through the fuel system and carburetor.

  • Page 23: Specifications

    SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER SPEcificATiONS Spark Plug Specifications OEM Type ............. F6RTC chipper-shredder Specifications Replacement Type ...... NGK BPR6ES or equivalent Max Diameter Chipper Material .

  • Page 24: Parts Diagram

    SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Parts Diagram...

  • Page 25: Parts List

    SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Parts List Part number Description Part number Description 31 601.303100.00.2 601.201702.00.48 Impeller Assembly, Black S/N: < Y2112220975 32 601.303004.00 Shredder Blade Wheel Cap, Yellow 254.201702.04.48 33 601.300024.00 Washer S/N: Y2203120001+ 34 2.03.063 Lock Washer, Ø12...

  • Page 26: Engine Parts Diagram

    SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Engine Parts Diagram...

  • Page 27: Engine Parts Parts List

    SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Engine Parts Parts List Part number Description Part number Description 23.061006.01 Recoil Handle, Big 59 2.08.014 Flange Bolt M10 x 80 1.5789.0608 Flange Bolt M6 x 8 60 46.020002.00 Gasket, Cylinder Head Cover 46.061100.00.2...
  • Page 28 SPEcificATiONS 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER Part number Description 116 24.070001.00 Fuel Valve Knob 117 1.818.0412 Bolt M4 x 12 118 45.110001.00 Shaft, Governor Arm 119 2.03.019 Washer Ø8.2 x Ø17 x 0.8 120 2.11.006 Oil Seal Ø7 x Ø14 x 5 121 45.110008.00...

  • Page 29: Troubleshooting

    TROUbLEShOOTiNG 500137-N - 3 iN. (7.6 cM) chiPPER ShREDDER TROUbLEShOOTiNG Problem Cause Solution No fuel. Add fuel. Engine will not start. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Fill crankcase to the proper level.

Table of Contents