Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Danfoss ET1187
Summary of Contents for Danfoss ET1187
- Page 1 Operator’s Manual ET1187 Crimp Machine...
- Page 2 Weatherhead fitting tolerances are engineered Weatherhead hose and fittings specified 12. KEEP WORK AREACLEAN. Cluttered areas to match Aeroquip and Weatherhead hose tol- for this assembly equipment. and benches invite accidents. 2 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 3 * These pump kits include the pump, connecting hose assembly, and all of the GH681/H180, GH781/H280, GH493/H430 adapters necessary to connect the pump to the ET1187 crimp machine. ET1187-002 = Truck Mount Machine, no pump, no tooling (includes bracket) - for premium hose...
- Page 4 † - Die cage used to crimp Winner Hose with Two Piece Winner Fitting † †- Die cage used to crimp Winner Hose with 4S Fitting Note: Additional dies and die cages also available. Refer to website or contact Danfoss. 4 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02.
- Page 5 2 to 3 turns past hand tight). bly to the cylinder adapter with the –06 size 37 degree swivel nut fittings using 18- 20 ft. lbs. assembly torque. 5 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 6 fitting. NOTE: Collar has detents at each position to help ensure proper alignment with corre- sponding product groups. 6 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 7 -16 horizontal line on the collar is even with the top of the crimp adjustment ring. 7 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 8 Source for the ET1187 crimp machine for the each mark around the dial corresponds to a initial setting. 001 change in target setting. Figure 10 Figure 11 Figure 22 8 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 9 3. Reassemble components and liberally apply Accrolube to the die surface which slides along the spring plate. Torque the die cage bolts to 50in.-lbs . 4. Ensure that all dies slide in and out freely. 9 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 10 LUBRICANT (Not Shown) ET1187C-0012 QUICK RELEASE PIN ET1187C-0013 QUICK RELEASE PIN ET1187C-0014 SHOULDER SCREW ET1187C-0015 SPRING PLUNGER ET1187C-0016 ROLL PIN ET1187C-0017 BENCH MOUNT STAND ET1187C-0018 WALL MOUNT BRACKET ET1187C-0019 SHROUD 10 | ©Danfoss ET1187 Crimp Machine Operator’s Manual | 2023.02. AQ435956054218en-000101...
- Page 11 Phone: +86 21 3418 5200w Danfoss can accept no responsibility for possible errors in catalogs, brochures, and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
Need help?
Do you have a question about the ET1187 and is the answer not in the manual?
Questions and answers