Electrolux EWH 30-100 Fmx EEC User Manual page 7

Panel board FmxDL EEC
Figure 4
1. Panel board.
2. "ON"/"OFF" button — turning on/off the
water heater (heating).
3. Temperature adjustment button — "-"
temperature decrease.
4. Temperature adjustment button — "+"
temperature increase.
5. "SET" button:
– viewing the set temperature;
– memorizing the set temperature;
– setting the temperature from the water
heater memory
6. "POWER" button — heating power
adjustment.
Display of the selected heating power
level:
- 1 stage — 800 W.
- 2 stage — 1200 W.
- 3 stage — 2000 W.
- 4 stage - 2000 W Smart Features:
Press the POWER key four times, the digital
screen area 7 of the display screen displays
4 steps, the ECO indicator blinks, the
temperature cannot be adjusted (" - ", "+",
"set" key is invalid), that is, the intelligent
control mode is entered. In the intelligent
control mode, press the on key again to exit
the intelligent control mode and return to
the 3step mode.
The program starts timing from 00:00, and
the temperature is fixed at 75 degrees in
the first week. From Monday to Friday of
the second week, the setting temperature
changes every day according to the time
point.
65 degrees at 5:00,
45 degrees at 7:00,
50 degrees at 8:00,
70 degrees at 10:00,
55 degrees at 16:00,
65 degrees at 18:00,
60 degrees at 19:00,
60 degrees at 20:00,
45 degrees at other times.
The temperature is fixed to 50 degrees
on Saturday and Sunday. Then repeat
the temperature setting method for the
second week every week. After the device
is powered on again, cancel the intelligent
control and return to the 3 step mode.
The choice of power mode provides fast
heating or allows the use of the water heater
in rooms with limited power supply.
Networking models Fmx EEC
Insert the plug into a socket outlet and
turn the water heater on. The indicator will
light up. This means that the water heater is
connected to the power supply network and
supplied with power. Turn the temperature
control knob counterclockwise to turn
heating on. By adjusting the temperature,
set the desired water heating level. Indicator
«ECO» — economic mode, corresponds to
heating temperature of about 55 °С. Water
heating is automatically turned off when
the set temperature is reached and turns on
automatically for heating. If you want to turn
off water heating, turn the temperature control
knob to the «OFF» position. The power-on
indicator will be lit while the water heater is
connected to the power supply network. On
some models, when the heating element is
turned on, the indicator light blinks. Upon
some water consumption, the thermostat will
turn the heating element on again.
Temperature setting
Water heater temperature adjustment range
is between 30 °С (minimum) and 75 °С
(maximum). The temperature is set using the
regulator located on the front panel of the
device.
Networking models FmxDL EEC
Plug the water heater into a socket. The
water heater will start self-diagnosis. The
indication on the display will flash for
about 2 seconds, only the indication of the
temperature of the water in the water heater
will be on — the water heater has switched
to "STAND BY" mode. If the water heater
detects any errors during self-diagnosis, the
entire display will flash continuously.
Turning on and setting the temperature
After pressing the button
will turn on and the Heating indicator will
light up red, the last set temperature or the
factory setting ECO — 55 °C set during the
first start-up, will flash red for 2 seconds.
After 2 seconds, the set temperature display
will turn off and water heating will start. The
display will show the temperature of the
water in the water heater.
For ease of use, you can set an individual
water heating temperature mode, which will
ENGLISH
the water heater
7