Related Manuals for Nauticam NA-OM-1
Summary of Contents for Nauticam NA-OM-1
-
Page 1: Table Of Contents
May, 2022 NA - OM1 For Olympus OM-1 Camera PN 17819 User Manual Housing Introduction Package Contents Important Instructions Part Names and Functions Housing Mount Opening the housing Closing the housing Preparation for Use Optional Accessories Care/Storage Warranty Specifi cations... -
Page 2: Introduction
PACKAGE CONTENTS Make sure that you have all the included items listed below before using this product. If some items are missing or damaged, contact your local Nauticam dealer. NA-OM1 Padded Travel Case... -
Page 3: Important Instructions
Only the accesories specifi ed by Use only Nauticam lubricant on silicone Nauticam must be used. Third-party rubber O-ring. accessories may result in malfunctions or damage to the product. -
Page 4: Part Names And Functions
PART NAMES AND FUNCTIONS Rear View Flash on/off lever MENU button LV button 0.66x viewfi nder AEL button REC button ISO button FN lever Up button Right button INFO button Playback button Moisture alarm window Multi selector Left button Delete button Down button Multi selector - center... - Page 5 PART NAMES AND FUNCTIONS Top + Front Views M24 Accessory port Sequential shooting/self-timer/fl ash button AF button ON/OFF lever M14 Accessory port Mode button Exposure compensation button M10 thread hole Real dial Mode dial Accessory mounting ball Preview button Port index mark Lens release button...
- Page 6 PART NAMES AND FUNCTIONS Back + Side Views 1/4” Threaded tripod holes Sacrifi cial zinc anodes Zoom/Focus knob Port lock safety button AF-ON lever Shutter release lever Housing unlock button Front dial...
-
Page 7: Housing Mount
HOUSING MOUNT Housing mount Compatible accessories 25311 Strobe mounting ball for cold shoe M10 Accessory coldshoe 25321 Long strobe mounting ball for cold shoe 25312 Light mounting stem for cold shoe 25322 Long light mounting stem for cold shoe 25221 M10 Strobe mounting ball M10 Accessory port 25224... -
Page 8: Opening The Housing
OPENING THE HOUSING * drawings as illustrations only depress housing unlock button turn housing lock latch anti-clockwise to open the housing fl ip open the back housing when lock latch is aligned to ‘open’ position... -
Page 9: Closing The Housing
CLOSING THE HOUSING * drawings as illustrations only before closing the housing, clean and lubricate the main O-ring make sure nothing is caught between front and back housing and that they are fully aligned before locking main O-ring insert the housing shaft into the shaft hole and then rotate the lock latch clockwise until you hear and feel it click into place... -
Page 10: Preparation For Use
PREPARATION FOR USE * drawings as illustrations only Installing the Camera - housing tray attachment unlock camera tray lever and remove the tray from the housing attach the camera tray by tightening the tray screw into the tripod socket of the camera make sure the camera buttons are engaged with the camera tray * pull out the zoom/focus knob if... - Page 11 PREPARATION FOR USE * drawings as illustrations only Port Mounting depress port lock safety button and rotate anti-clockwise lubricant the port O-ring before mounting align index mark push port assembly straight in rotate locking lever clockwise to lock...
- Page 12 PREPARATION FOR USE * drawings as illustrations only Coating housing O-ring Main O-ring remove the main O-ring using an O-ring remover clean the O-ring groove with a cloth and ensure that it is free from salt or other foreign materials lightly coat it with provided lubricant return the main O-ring by slowly pressing from one corner to the whole perimeter...
- Page 13 PREPARATION FOR USE * drawings as illustrations only Setting up moisture alarm CR2032 Battery Alarm ON/OFF remove battery press the battery down until it insulation fi lm click into place switch on the alarm test the alarm - the moisture alarm - connect the wires with a window will fl...
- Page 14 PREPARATION FOR USE * drawings as illustrations only Changing lens/port without opening the housing If using with vacuum valve : remove the cap from the vacuum valve and press the red button to release pressure before unlocking port lock If using without vacuum valve, please follow from step 2 unlock port lock and remove port assembly...
-
Page 15: Optional Accessories
OPTIONAL ACCESSORIES * drawings as illustrations only Vacuum valve system remove the plug of M14 accessory port from the housing remove the cap from the vacuum valve hand pump slightly lubricate the o-ring and make sure the o-ring is in place vacuum valve accesory port then tighten the vacuum valve to... - Page 16 OPTIONAL ACCESSORIES Installing Viewfi nder fi rstly remove the pre-installed 0.66x viewfi nder gently push the 0.66x viewfi nder from the inside of from the housing by removing the retainer o-ring the housing inside rear housing to use with 32211/32213 viewfi nder, exhchange a remove the retainer o-ring from the viewfi...
-
Page 17: Care/Storage
CARE/STORAGE Soak the housing system in fresh water Operate all controls and buttons at after salt water usage least 3 times while immersed in fresh water We recommand cleaning and inspecting Protect the housing with robust and the main O-ring each time after diving for shock-proof travel case during trans- any damage and every time the housing portation. -
Page 18: Warranty
NAUTICAM accepts no liability for any damage to and defects in the housing caused by improper use and/or poor maintenance; it is the responsibility of the own- er to carefully follow the instructions in our manuals. -
Page 19: Specifications
Monitor options ( 2.0 ) Monitor options ( 1.4 ) 17922 Nauticam Atomos Ninja V Housing for Atomos Ninja V 5” 17922S Nauticam Atomos Ninja V-S Housing for Atomos Ninja V 5” 17923 NA-Shinobi-H Housing for Atomos Shinobi 5.2” 4K HDMI Monitor... - Page 20 87517 EMWL Bayonet Holder for Ø90 Float Arm 24mm Lenses (incl. fl oat collar) 85201 0.36x Wide Angle Conversion Port *please refer to Nauticam port charts for more setup information. with Aluminium Float Collar (incl. N120 to N100 port adaptor) FLASH TRIGGERING...
- Page 21 *36146 P1442X-PZ Panazonic Lumix G X Vario PZ 14-42mm F3.5-5.6 ASPH. POWER O.I.S. (H-PS14042) zoom gear *36061 P1442X-PZ Zoom Gear for Panazonic Lumix G X Vario PZ 14-42mm F3.5-5.6 ASPH. POWER O.I.S. 36051 Adaptor for Olympus 4/3 port and gear system *Please contact to Nauticam for a customized gear.
- Page 22 Nauticam Internationl Ltd. Rm 2203, CCT Telecom Bldg, 11 Wo Shing St, Fo Tan, Hong Kong Tel. +852 - 26902711 Fax. +852 - 26909778 URL. www.nauticam.com Gallery. www.nauticam.smugmug.com...
Need help?
Do you have a question about the NA-OM-1 and is the answer not in the manual?
Questions and answers