EWM Phoenix 352 puls MM Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.14.5
5.14.6
5.15 Protecting welding parameters from unauthorised access .......................................................... 48
5.15.1
5.16 Definition of MIG/MAG welding tasks .......................................................................................... 49
5.16.1
5.16.2
5.16.3
5.16.4
5.16.5
5.16.6
5.16.7
5.16.8
5.16.9
5.16.10 Main program A mode .................................................................................................. 62
5.16.11 MIG/MAG overview of parameters for M3.1x ............................................................... 63
5.17 "Special Mode" mode ................................................................................................................... 64
5.17.1
5.17.2
5.17.3
5.17.4
5.17.5
5.18 "JOB Info" mode ........................................................................................................................... 66
5.19 Operating time counter ................................................................................................................. 66
5.20 Organising welding tasks (Mode "JOB Manager") ....................................................................... 67
5.20.1
5.20.2
5.20.3
5.21 Expert parameters ........................................................................................................................ 69
5.21.1
5.21.2
5.21.3
6 Maintenance, care and disposal ......................................................................................................... 70
6.1 General ......................................................................................................................................... 70
6.2 Maintenance work, intervals......................................................................................................... 70
6.2.1
6.2.2
6.2.3
6.3 Maintenance work ........................................................................................................................ 71
6.4 Disposing of equipment ................................................................................................................ 72
6.4.1
6.5 Meeting the requirements of RoHS .............................................................................................. 72
7 Rectifying faults .................................................................................................................................... 73
7.1 Checklist for rectifying faults ........................................................................................................ 73
7.2 Error messages (power source) ................................................................................................... 75
7.2.1
7.3 Display machine control software version .................................................................................... 77
7.3.1
7.4 Vent coolant circuit ....................................................................................................................... 78
4
Automation interface ..................................................................................................... 45
Sensor Voltage ............................................................................................................. 47
Welding data display ..................................................................................................... 48
Welding task selection .................................................................................................. 50
5.16.1.1 Selecting or defining a new job ..................................................................... 50
forceArc / forceArc puls ................................................................................................ 51
coldArc / coldArc puls ................................................................................................... 52
5.16.3.1 Operating mode ............................................................................................. 53
Welding type ................................................................................................................. 53
5.16.4.1 Program or control voltage mode .................................................................. 53
5.16.4.2 Program sequence ........................................................................................ 54
5.16.4.3 superPuls ...................................................................................................... 55
MIG/MAG functional sequences / operating modes ..................................................... 56
Explanation of signs and functions ............................................................................... 56
MIG/MAG program sequence ("Program steps" mode) ............................................... 61
Selection ....................................................................................................................... 61
MIG/MAG overview of parameters for M3.1x ............................................................... 61
5.16.10.1 Selection ........................................................................................................ 62
Selection ....................................................................................................................... 64
Switching the Hold function on and off ......................................................................... 65
Wire feed speed switching (absolute / relative) ............................................................ 65
Resetting JOBs to status on delivery (Reset ALL) ....................................................... 65
Exiting "Special Mode" after making changes .............................................................. 65
Creating a new JOB in the memory or copying a JOB ................................................. 67
Loading an existing job ................................................................................................. 68
Resetting an existing JOB to the factory setting (Reset JOB) ...................................... 68
Selecting expert model parameters .............................................................................. 69
Selecting variables (5 model points) ............................................................................. 69
Setting parameters ....................................................................................................... 69
Daily maintenance tasks ............................................................................................... 70
6.2.1.1 Visual inspection ........................................................................................... 70
6.2.1.2 Functional test ............................................................................................... 70
Monthly maintenance tasks .......................................................................................... 71
6.2.2.1 Visual inspection ........................................................................................... 71
6.2.2.2 Functional test ............................................................................................... 71
Annual test (inspection and testing during operation) .................................................. 71
Manufacturer's declaration to the end user .................................................................. 72
Interface for automated welding ................................................................................... 76
Resetting JOBs to status on delivery (Reset ALL) ....................................................... 77
099-005376-EW501
18.07.2014