Table of Contents
Advertisement
Quick Links
Centronic SunWindControl
SWC441A-II
Assembly and Operating Instructions
en
Hand-held transmitter for sun/wind control
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
4033 630 278 0 14/07/2022
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Becker Centronic SunWindControl SWC441A-II
Summary of Contents for Becker Centronic SunWindControl SWC441A-II
- Page 1 Assembly and Operating Instructions Hand-held transmitter for sun/wind control Important information for: • Fitters / • Electricians / • Users Please forward accordingly! These instructions must be kept safe for future reference. 4033 630 278 0 14/07/2022 Becker-Antriebe GmbH Friedrich-Ebert-Straße 2-4 35764 Sinn/Germany www.becker-antriebe.com...
-
Page 2: Table Of Contents
Table of contents General .................... 3 Warranty .................... 3 Safety instructions ................... 4 Intended use ................... 5 Explanation of displays and buttons ............ 6 Explanation of functions ................ 6 Factory default settings ................ 9 Programming the transmitter .............. 9 Installing the wall bracket................. 10 Changing batteries.................. 11 Cleaning.................... 11 Technical data .................. 12... -
Page 3: General
General With this transmitter you are able to control one or more sun protection sys- tems, and set the threshold values for sun protection and wind monitoring with the setting tool included. This device is exceptionally easy to use. Please observe these Assembly and Operating Instructions when installing and setting up the equipment. -
Page 4: Safety Instructions
Safety instructions General information • Please keep the instruction manual safe! • Only use in dry rooms. • Only use unmodified original parts from the control unit manufacturer. • Keep children away from control units. • Observe all pertinent country-specific regulations. •... -
Page 5: Intended Use
Intended use The transmitter described in these instructions must only be used indoors for the operation of Centronic-compatible radio drives and radio control units for sun protection systems. Attention A safety-relevant function has been provided for the threshold controllers. Setting the threshold values wrongly can cause damage to the sun protection system. -
Page 6: Explanation Of Displays And Buttons
Explanation of displays and buttons 1. Setting tool 7. Channel indicator lamp 2. Wind threshold regulator 8. Slide switch 3. Sun threshold regulator 9. Programming button 4. RETRACT button 10. Labelling field 5. STOP button 11. Type plate 6. EXTEND button Explanation of functions Manual/Automatic slide switch In slide switch position "... - Page 7 The automatic sun protection functions are interrupted if a manual drive com- mand is carried out when in automatic mode. These functions are automatic- ally re-activated if upper/lower threshold limits are violated, following retrac- tion, or if the slide switch is switched from " " to " " and back to " ". Channel The channel of a transmitter can be programmed into one or more receivers.
- Page 8 Wind threshold regulator (in connection with a suitable sensor from the controller manufacturer) You set the wind threshold value with this regulator (between about 2 m/s and 22 m/s). The wind threshold value can be adjusted in 11 steps. When slowly turning the regulator, the tubular drive clicks to indicate the setting changes.
-
Page 9: Factory Default Settings
TEST mode The TEST mode is activated by adjusting the threshold value. It automatically ends after about 15 minutes. In TEST mode, the time for which the wind is monitored is shortened. Factory default settings Sun threshold value Medium setting (about 25 kLux) Wind threshold value Left stop (about 2 m/s) Programming the transmitter... -
Page 10: Installing The Wall Bracket
• Switch off the power supply to the receiver for 5 seconds, then switch it back on • Operate the programming button or the radio switch of the receiver. The receiver is now in programming mode for 3 minutes. b) Programming the master transmitter Press the programming button on the master transmitter while in program- ming mode until the receiver confirms that programming has been successful. -
Page 11: Changing Batteries
Changing batteries You will find the appropriate battery type in the "Technical data" chapter. Cleaning Only clean the device with a suitable cloth. Do not use aggressive cleaning agents that may damage the surface. 11 - en... -
Page 12: Technical Data
Technical data Rated voltage 3 V DC Battery type CR 2430 Degree of protection IP 20 Permissible ambient temperature -10 °C to +55 °C Maximum emitted transmission output ≤ 3 mW Radio frequency 915.3 MHz The maximum transmitter range on and in the building is up to 15 m, and up to 150 m in the open. - Page 13 Problem Remedy System does not extend automatic- Wind threshold value exceeded. Wait ally manually slide switch is set to " " for the wind to die down. or " ". 13 - en...
Need help?
Do you have a question about the Centronic SunWindControl SWC441A-II and is the answer not in the manual?
Questions and answers