Page 1 V2 Series III Owner’s Handbook. www.holden.com.au...
Page 3: Table Of Contents
Specifications 8 Engine and general specifications, capacities, identification plates, dimensions. After Sales 9 warranty, Holden Retailers, Holden Roadside Assistance, Customer Assistance. Tow and load 1 0 Loading information, towing equipment, towing precautions. Cleaning 11 Interior cleaning, washing, list of maintenance materials.
Page 4 We thank you for choosing Holden and want to assure you of our continuing interest in your driving pleasure and satisfaction. This handbook applies to the current Monaro model. Therefore, due to different models and options, you may find reference in this Handbook to some equipment not fitted to your own vehicle.
Page 5 Please mail to the address on the back of this page. If Holden Assist is fitted, please also press the Assist button on the rear view mirror to advise of change of address I ownership. Please tick the appropriate box:...
Page 6 Place in an envelope and mail to: The Manager- Warranty Administration Service Department Holden Ltd Box 5480, G.P.O. Melbourne Victoria, 3001...
Page 7 Please mail to the address on the back of this page. If Holden Assist is fitted, please also press the Assist button on the rear view mirror to advise of change of address I ownership. Please tick the appropriate box:...
Page 8 Place in an envelope and mail to: The Manager- Warranty Administration Service Department Holden Ltd Box 5480, G.P.O. Melbourne Victoria, 3001...
Page 9 Please mail to the address on the back of this page. If Holden Assist is fitted, please also press the Assist button on the rear view mirror to advise of change of address I ownership. Please tick the appropriate box:...
Page 10 Place in an envelope and mail to: The Manager- Warranty Administration Service Department Holden Limited Box 5480, G.P.O. Melbourne Victoria, 3001...
Page 11: Dashboard
Dashboard Page Layout Gauges Warning I reminder indications 1-14 Turn signals, Horn, Tilt I reach steering 1-15 Trip computer 1-22 Customisation mode 1-30 Wipers and washers 1-31 Lights 1-34 Radio I CD and clock 1-36 Remote radio I CD controls 1-37 On-glass antenna 1-38...
Page 12 Chapter 1 DASHBOARD LAYOUT Page Glovebox 3-14 ............... Cup holders 3-18 .
Page 13 Chapter 1 DASHBOARD...
Page 14 Chapter 1 DASHBOARD GAUGES Speedometer The speedometer shows vehicle speed in kilometres per hour (kml Tachometer The tachometer shows engine speed in revolutions per minute (rpm). Sustained operation in the RED zone may cause serious engine damage. Automatic transmission: Under wide open throttle acceleration (accelerator pedal pushed flat to the floor) it is possible that the...
Page 15 If there are no warnings or service reminders, [f!]RND321 the display will show a series of Holden welcome screens displaying the Holden logo and finishing with the 'OK!' screen. Note: Pressing the MODE button any time during the system check will cause the display to jump ahead to the last trip computer screen displayed on the last ignition key off.
Page 16 1:::!1 animation illuminate while driving, it indicates that the alternator is not charging properly and Check that you should see your Holden Retailer. Alternator The 'Check Alternator' animation displays until PRN[Q]321 the MODE button on the trio com outer switch is...
Page 17 If the(@)) warning light and 'ABS Fault' animation illuminate when driving, a malfunction of the Anti-lock Brake System is indicated and you should see your Holden Fault Retailer. The vehicle's brake system will still PRN[Q]321 operate conventionally, only the anti-lock operation is disabled, refer to Chapter 4.
Page 18 PRN[Q]321 correctly, especially in an accident. You should your Holden Retailer immediately. The warning light illuminates after an accident where the pretensioners, or pr e t e nsion ers and airbag , have activated.
Page 19 Ctrl Off traction control system is not working and PRN[Q]321 you should see your Holden Retailer. The 'Traction Ctrl Off animation displays for 2 seconds. The animated symbol then reverts to the original trip computer display with a Odometer small TRAG OFF icon on the right.
Page 20 1-10 Chapter 1 DASHBO,�.RD WARNING I REMINDER INDICATIONS cont. Over temperature If the 'Engine Temp Hot' animation illuminates while driving, it indicates that Temp Hot � engine coolant t e mperature P R N [Q] 3 2 1 dangerously hot. You should stop the vehicle as soon as it is safe to do so.
Page 21 You should have the problem fixed as soon as possible. Your Holden Retailer has the correct diagnostic computer equipment and training to find and fix the problem.
Page 22 Service Error animation illuminates while driving, a fault Contact Retailer in the instrument panel is indicated. You should contact your Holden Retailer as PRNIQ]321 soon as possible. The 'Service Error' animation displays until the MODE button on the trip computer Odometer switch is pressed.
Page 23 Chapter 1 1-13 DASHBOARD WARNING I REMINDER INDICATIONS cont. Overs peed Overspeed is designed to warn you when 0/Speed km/h the pre-selected speed is exceeded. For information on the overspeed displays, refer to TRIP COMPUTER further on in this chapter. Power shift (with auto transmission) The automatic transmission 'Power Shift' Power...
Page 24 Chapter 1 '"'1\SHBr.. I\ R'"' U/"\ VI"\ TURN SIGNALS. HORN. TILT I REACH STEERING Turn signals The turn signals lever is on the right side of the steering column. Push the lever up to signal a left turn. down to signal a right turn. In some turns (such as changing lanes) the steering wheel is not turned far enough to cancel the turn signal.
Page 25 Chapter 1 1-15 DASHBOARD TRIP COMPUTER Two styles of trip computers are available, depending on the model of vehicle (CV8 or CV8R). However, the information displayed is the same for both models. The buttons for the trip computer are located to the left of the gauges. The triple-windows for the trip computer are located directly beneath the gauges.
Page 26 Chapter 1 1-1R I'")J\QLJOI\1\Dn I" L.lr-\VI ILJ\,Jr-\.1 'L.I TRIP COMPUTER cont. AVG FUEL Odometer SPEED S9.5km/h L/1 OOkm 012,689 km PRNI0]321 Average speed Odometer Average fuel Shows the average speed Records kilometres travelled Shows average fuel used (while the engine is running) since the vehicle was built.
Page 27 Chapter 1 1-17 DASHBOARD TRIP COMPUTER cont. TIME TO ARRIVAL l2:3Y SOOkm PRN[QJ321 *Distance to arrival *Time to arrival *Remaining fuel Shows trip time to arrival in At the start of a trip estimate Shows the litres of fuel left in your distance to arrival (from the fuel tank, rounded to the hours and minutes, based...
Page 28 TRIP COMPUTER cont. FUEL INST Dist to Empty 0/SPEED 1 Q km/h J2. y L/100km 420km PRN[Q]321 Distance to empty Overs peed Instantaneous fuel An estimate of how far your Shows instantaneous fuel Sets the speed you do not want exceed.
Page 29 Chapter 1 1-19 DASHBOARD TRIP COMPUTER cont. *Underspeed chime Overspeed provides a chime when your @km/h travelling speed exceeds the overspeed chosen v a lue, w h ereas underspeed provides a chime to indicate when your PRN[Q]321 travelling speed again drops below the overspeed value.
Page 30 Chapter 1 1-20 DA.SHBOA.RD TRIP COMPUTER cont. TAP MODE BUTTON *Stop watch The stop watch function, when enabled, Stop Watch records elapsed time. It can be used, tor 00:04:24.2 example, to measure the time taken to travel PRN[Q]321 between two points on a trip. To start I stop the stop watch, press the SET button.
Page 31 'Additional service requirements' in the service booklet in your glovebox. The Service due message will be reset for you by your Holden Retailer when you take your vehicle there to be serviced.
Page 32 Chapter 1 1-22 DASHBOARD CUSTOM/SA TION MODE Customisation Mode enables the driver to customise some of the vehicle features using the trip computer switch and instrument panel centre display. Note: Only features that are fitted to the vehicle will be displayed. Entering customisation mode Customisation Mode is accessible via the Options Menu, which can be displayed when the vehicle is stationary or moving slowly.
Page 33 Chapter 1 1-23 DASHBOARD CUSTOM/SA TION MODE cont. Options Once in Customisation Mode, the driver can step through the following series of options: RESTORE TO FACTORY SETTINGS RESTORE TO This option restores the instrument panel, FACTORY SETTINGS entertainment system and other general [R2J ..6..
Page 34 Chapter 1 1-24 DASHBOARD CUSTOM/SA TION MODE cont. TRIP COMPUTER A & 8 This option is used to select either one or TRIP COMPUTER A & 8 two Trip time I Trip distance I Fuel used set � TripA of displays. This set of displays is explained previously in this chapter.
Page 35 Chapter 1-25 DASHBOARD CUSTOM/SA TION MODE cont. SPEED DEPENDENT VOLUME SPEED This option is used to enable I disable the DEPENDENT VOLUME audio system speed dependent volume 1 2 3 4 L:::!. .. function. This function is explained further in the Audio System Handbook located in the glovebox.
Page 36 Chapter 1 1-26 DASHBOARD CUSTOM/SA TION MODE cont. COURTESY LAMP TIMEOUT This option is used to adjust the length of time that the interior courtesy lamp remains illuminated after opening a door or unlocking (at night only) the vehicle. Use the T or .A. button to adjust the time setting between zer o a n d...
Page 37 Chapter 1 1-27 DASHBOARD CUSTOM/SA TION MODE cont. ACCESSORY CONTROL ACCESSORY This option is used to enable I disable the CONTROL accessories timeout function. This function � DoorOpen is explained in detail in Chapter 3. Use the T or .._ button to select 'Off or 'Door Open' (Default Door Open).
Page 38 Chapter 1 1-28 DASHBOARD CUSTOM/SA TION MODE cont. ENTER CALIBRATION ADJUSTMENT ENTER This option is used to calibrate the trip CALIBRATION ADJUSTMENT computer distance and fuel figures. The trip [[QJ L::J. .. computer uses in its calculations different caiibration numbers. These figures preset for the standard vehicle and do not have to be adjusted.
Page 39 Chapter 1 1-29 DASHBOARD CUSTOM/SA TION MODE cont. FUEL CALIBRATION FUEL If Fuel Calibration is not required, press the CALIBRATION MODE button to advance to the EXIT OPTIONS MENU. If you wish to check I adjust the Fuel Calibration, work out the following BEFORE ENTERING CUSTOMISATION MODE: 1.
Page 40 Chapter 1 1-30 DASHBOARD WIPERS AND WASHERS The lever on the left of the steering column controls the wipers and washers, which operate when the ignition is turned to either on or accessories. Wipers and washers ��evei opeiate the vvipers on dry g!ass, this will damage the rubber and scratch the glass.
Page 41 Chapter 1 1-31 DASHBOARD LIGHTS All lights off Park lights Dimmer- instrument lighting Turns on the park, tail, The instruments are automatically rear licence illuminated when the park lights instrument panel lights. are switched on. The lighting c a n be adjusted anywhere between dim and bright by holding the tab in the bright or dim position until the desired level...
Page 42 Chapter 1 1-1? nAcuof"\ADn '\J- LJ/"""\ v l ILJ\.J/"""\ 1 '\LJ LIGHTS cont. Automatic headlights When the headlight switch is left in the AUTO position, the headlights and park lights automatically switch off and on with the ignition switch or through the approach lighting feature (refer to 'Headliqhts on when approachinq the vehicle').
Page 43 Chapter 1 1-33 DASHBOARD LIGHTS cont. Fog lights Fog lights are designed to provide a different illumination of the road to the usual headlight beam. Depending on the density of the fog, different combination of lights will improve vision. For instance, in very heavy fog, vision may be improved by turning the headlights off, and just having the park lights and fog lights on.
Page 44 Chapter 1-34 DASHBOARD RADIO I CD AND CLOCK Radio, CD and clock Detailed information on the operation of the radio and CD player is provided by the Audio System Handbook in the glovebox. An overview on the radio disolav. how to adiust clock.
Page 45 If your Security Card is lost and the PIN is not recorded elsewhere, the PIN can be requested from your Holden Retailer, after supplying the proof of ownership and the Vehicle Identification Number shown on the inside front cover of this handbook. There may be a nominal charge for this service.
Page 46 Chapter 1 1-36 DASHBOARD REMOTE RADIO I CD CONTROLS Remote controls for the radio I CD player are provided by buttons located on the left side and right side of the steering wheel centre pad. Left side Pressing the MODE button alternates between different audio modes: radio FM1, radio FM2, radio AM and CD.
Page 47 A special mobile phone aerial pad which minimises interference can be fitted by your Holden Retailer. Window tinting is not recommended on rear windows with the on-glass antenna.
Page 48 Chapter 1 1-38 DASHBO.A.RD PHONE Mobile phone connection A power connection for fitting a mobile telephone is provided for all models. The connector is taped under the centre console, on the passenger's side.
Page 49 Chapter 1 1-39 DASHBOARD VENT/LA TION SYSTEM The vehicle features a flow-through ventilation system for your comfort. Under reasonable conditions, it should not be necessary to open the windows at any time. Outside air (except when recirculate is selected) is drawn into the vehicle through the opening between the bonnet and the windscreen.
Page 50 Chapter 1 1-40 DASHBOARD CLIMATE CONTROL The Climate Control panel is located in the centre of the dashboard. It is designed to maintain the interior of your vehicle at your desired temperature. Right and left sides of the vehicle can be maintained at different temperatures (dual zone). Automatic operation Start the engine.
Page 51 Chapter 1 1-41 DASHBOARD CLIMATE CONTROL cont. Dual zone linking The left and right sides of the vehicle can be set to different temperatures or can be linked to operate identically, that is the passenger's side will mirror whatever the driver's side is changed to.
Page 52 Chapter 1 1-42 DASHBOARD CLIMATE CONTROL cont. FLOOR DEMIST AND 81-LEVEL FACE FLOOR (BLEND) Air is directed to the Cooler air is directed Air is directed to the floor vents. Air is directed to to the face and rear face and rear vents. t he f l o o r a n d...
Page 53 Chapter 1 1-43 DASHBOARD CLIMATE CONTROL cont. RECIRCULATION Switches air intake to recirculated air. Recirculate reuses i nter i or air an d is therefore not recommended for long periods of time. Recirculate position should NOT be used if occupants are smoking. Recirculation automatically switches off after 40 minutes, or it can be manually turned off by pressing the switch again.
Page 54 Chapter 1 1-44 DASHBO . .&.RD CLIMATE CONTROL cont. Press on the fan switch to increase or decrease the fan speed. Five manual fan speeds are available. When the fan has been adjusted manually the fan blades will fill according to the fan speed, for speeds 1 to 4.
Page 55 Chapter 1 1-45 DASHBOARD CLIMATE CONTROL NOTES Ignition keys Your vehicle is fitted with a 'priority key locking' systems (refer to Chapter 2 'Locks') which has the ability to remember individual adjustments for different keys. When the key is inserted in the ignition and turned on, the system identifies the key and sets the climate control to the last adjustments used for that key.
Page 56 Something wrong? This symbol shows on the display when there is a fault in the system. You should see your Holden Retailer, who has the necessary equipment to diagnose the system. Sensors The climate control uses different sensors to maintain your desired temperature.
Page 57 Chapter 1 1-47 DASHBOARD CRUISE CONTROL The cruise control maintains your vehicle's speed without you having your foot on the accelerator pedal. The cruise control lever is on the right side of the steering column. The ON-OFF I CANCEL switch is at the end of the lever and is activated by pushing in towards the direction of the steering column.
Page 58 Chapter 1 1-48 DASHBOARD CRUISE CONTROL cont. TO ADJUST YOUR SET SPEED You may either: Rotate the lever down to the SET-DECEL position until the vehicle slows down to the desired speed. then release. Rotate the lever up to the RES-ACCEL position until the vehicle accelerates up to the desired speed, then release.
Page 59 Chapter 1 1-49 DASHBOARD CRUISE CONTROL cont. WARNING: Do not use the cruise control when road or driving conditions require varying speeds. A constant speed isn't practical in heavy or varying traffic, or on winding, slippery or rough roads. Remember that when both the 'CRUISE' and the 'ACTIVE' symbols are showing the cruise control is maintaining your speed.
Page 60 Chapter 1 1-50 DASHBOARD REVERSE PARKING AID Reverse Parking Aid (RPA) is designed to help the driver reverse the vehicle by indicating (with varying tones) the distance to the nearest obstacle behind the vehicle. The RPA starts automatically when the ignition is on and reverse gear is selected. A short single tone from the speaker indicates that the RPA is operational.
Page 61 Tow bar: When a tow bar is fitted to the vehicle, the RPA requires adjustment to allow for the protrusion of the tow bar. Your Holden Retailer will automatically adjust the RPA when fitting the tow bar. If the RPA should require tow bar adjustment by the owner due to the removal or installation of a tow bar, proceed as follows: Ensure that the ignition is turned off.
Page 62 No tones or a deep continuous warning tone after engaging reverse gear- system defective (contact your local Holden Retailer). Safety Instructions When reversing the vehicle, the driver must still drive in such a way as to avoid all risks to others on the road.
Page 63 Chapter 1 1-53 DASHBOARD NAVIGATION SYSTEM Detailed information on the operation of the in-car navigation system (SATNAV) is provided by the supplement in the glovebox. Note: If a vehicle fitted with a SATNAV system is towed, the antenna will need to redefine the position of the vehicle, as only the previous location prior to towing is stored in the memory.
Page 64: Locks
Locks Page Keys 2- 4 Door locks 2- 7 Alarm Ignition lock 2-10 Free turning door locks 2-11 Boot lock Bonnet lock 2-12...
Page 65 VIN (PSN) XXXXXXXXXXXXXXXX IGNITION KEY No. XXXXX vehicle. If a key is lost, a replacement can RADIO P.I.N. XXXXXX be ordered through any Holden Retailer by SECURITY No. XXXXX GLOVE BOX No. quoting the key code number, security XXXXX ENGINE No.
Page 66 Chapter 2 LOCKS KEYS cont. Personal identity keys This system provides two different memories of electronic settings, for different keys. For instance, one driver may have a preferred radio station. Pressing the UNLOCK button on their key will automatically customise the radio for that driver. However, the other driver may prefer a different station.
Page 67 Chapter 2 LOCKS DOOR LOCKS Lock Doors are locked when the lock knob is down. Automatic vehicles have an 'Auto lock in drive' feature which locks the doors automatically when the transmission selector is shifted out of Park. This feature can be selected from the instrument panel Customisation Mode (refer to CUSTOMISATION MODE in Chapter 1 ).
Page 68 Chapter 2 LOCKS DOOR LOCKS cont. Note: If unsure whether the vehicle is locked or deadlocked, press the LOCK button on the key. If the vehicle is already deadlocked the lights will give a long flash; if the vehicle is locked, the lights will give a short flash, but will not engage the deadlocking. If the LOCK button is pressed twice within 10 seconds, the lights will give a long flash to indicate that deadlocking has occurred.
Page 69 Try pressing LOCK on the key again. If it still does not work a replacement key may be needed from your Holden Retailer. If, for any reason, pressing the key buttons will not work, the doors can still be locked and unlocked by turning the key in the driver's door lock.
Page 70 Chapter 2 LOCKS ALARM Switching on and off The alarm system is turned on when the LOCK button on the key is pressed, and turned off when UNLOCK is pressed. Therefore, locking the doors by pressing LOCK not only locks both the doors but (after a short delay) also sets the alarm system. When set off The alarm is triggered when any of the doors, bonnet or boot are opened or a hot-wire attempted;...
Page 71 Chapter 2 LOCKS ALARM cont. Notes Remember, the alarm system is turned off and on when the UNLOCK and LOCK buttons on the key are pressed. When the alarm system is switched on, turning the key in the lock and then opening a door triggers the alarm. The alarm system thinks a break-in has occurred.
Page 72 Chapter 2 LOCKS IGNITION LOCK WARNING: Accessories Do not turn the engine off while the vehicle is moving or there will not be any power assist for brakes or steering. Never remove the key while the vehicle is moving, as this will lock the steering.
Page 73 If you have problems with the free turning door locks, contact your Holden Retailer (refer to Chapter 9).
Page 74 Chapter 2 2 11 LOCKS BOOT LOCK Use one of the methods shown below to unlock the boot. After partly opening the boot lid, gas struts automatically take over to lift and hold the boot lid in the fully open position. The boot locks automatically when pushed shut, so be careful not to leave keys in the boot, as they will be locked in when it is shut.
Page 75 Chapter 2 2-12 LOCKS BONNET LOCK To open From the driver's side of the vehicle, pull the lever shown towards you. T his allows the bonnet to release but is prevented from opening by the safety catch. To open completely, reach under the centre of the bonnet and move safety catch upwards.
Page 76 Chapter 2 LOCKS...
Page 77 Know your vehicle Page 3 -2 Front seat Rear seat entry Seat belts 3 -6 Which type of child restraint for 3- 8 your child? Child restraints Windows 3-10 Mirrors 3-11 3-12 Interior lights Accessory control and battery 3-13 saver Glovebox and centre console 3-14 3-15...
Page 78 Chapter 3 KNOW YOUR VEHICLE FRONT SEAT Two switches are fitted to the front seats. The front switch is used to electrically adjust the height, the tilt and the movement of the seat forwards and backwards. The rear switch is used to electrically adjust the recline angle of the back of the seat. Adjustment to lumbar support and head restraints are made manually.
Page 79 Chapter KNOWYOURVEHICLE FRONT SEAT cont. WARNING- SIDE IMPACT AIRBAGS: Do not fit unauthorised seat covers as they may impair the deployment of the Side Impact Airbags. Do not position your body or any object (including pillows) between front seats and doors. Front seat occupants should not lean on or sleep against the door. Always sit centrally in the seat (refer also to 'Airbags' in Chapter Lumbar support Move the wheel (on the door side of the seat) to alter support given to the lower part of...
Page 80 Chapter 3 KNOW YOUR VEHICLE REAR SEAT ENTRY Moving the seat forward Both front seats have a lever on the outside edge to enable rear seat entry and exit. WARNING: Seats can be moved at any time, regardless of the ignition key position. It is therefore important notto leave children unsupervised in the vehicle.
Page 81 Chapter 3 KNOW YOUR VEHICLE REAR SEAT ENTRY cont. Moving the seat rearwards WARNING: Before moving the seat rearwards, ensure that nobody in the rear can become pinned between the front and rear seats. Before moving the seat, ensure there are no objects in front or behind the seat.
Page 82 Chapter 3 KNOW YOUR VEHICLE SEAT BELTS sash belts To fasten, pull the metal tongue across your body and clip it into the buckle. When the metal tongue is locked safely into place you will hear a 'click'. After fastening, settle the belt at the hip, and run your hand under the sash from hip to shoulder to ensure that the belt fits comfortably and is free from twists.
Page 83 If the SRS warning light comes on at any other time, or if the warning 'SRS Airbag Fault' displays on the instrument panel, you should see your Holden Retailer immediately to have the system checked. Refer to Chapter 1 for further information about warnings and reminder indications.
Page 84 Chapter 3 KNOW YOUR VEHICLE WHICH TYPE OF CHILD RESTRAINT FOR YOUR CHILD? Children should be restrained at all times and fitted with a child restraint appropriate to their size when travelling in a vehicle. Following are some guidelines about selecting the appropriate restraint for your child.
Page 85 Chapter 3 KNOWYOURVEHICLE CHILD RESTRAINTS WARNING - EXTREME HAZARD: Do not use a rearward facing child restraint on a seat protected by an airbag in front of it. NEVER install a child restraint in the front seat of a Monaro. The Monaro is fitted with Passenger and Side Impact Airbags (SlAB) and the child could be seriously injured if either airbag inflates,...
Page 86 Chapter 3 3 1 0 KNOW YOUR VEHICLE WINDOWS Power windows T he window switches are located between the front seats. The s'vvitches also remain operational Vv'hen the ignition is turned offfor60 minutes while the doors remain closed and for 45 seconds after a door is opened.
Page 87 Chapter 3 3-11 KNOW YOUR VEHICLE MIRRORS Internal rear view mirror, auto day I night switch A switch is provided on the lower edge of the mirror. When the switch is set to on, the mirror will automatically switch in and out of night view, as required.
Page 88 Chapter 3 3 12 KNOW YOUR VEHICLE INTERIOR LIGHTS Interior (dome) light The interior light is located in the centre of the roof. It can be switched to: (always off), ON (always on), or DOOR (door activated). Door setting notes: The light automatically switches on when a door is opened and Reading switches off 30 seconds after all doors are...
Page 89 Chapter 3 3-13 KNOW YOUR VEHICLE ACCESSORY CONTROL AND BATTERY SAVER Accessory control Your vehicle is equipped with an accessory control feature that can be set at the instrument panel to shut down all accessories (radio, power socket, wipers etc.) either when the ignition key is turned off, or when the driver's door is opened (refer to Chapter 1, CUSTOMISATION MODE for details about this setting).
Page 90 Chapter 3 3-14 KNOW YOUR VEHICLE GLOVEBOX AND CENTRE CONSOLE Glove box T he glovebox is located in the dashboard directly in front of the passenger's seat. A specific key is provided soieiy to iock and unlock the glovebox. For security, the master key is not designed to operate the glovebox lock.
Page 91 Chapter 3 3-15 KNOW YOUR VEHICLE STORAGE COMPARTMENTS Front and rear storage compartments vehicles built with storage compartments, front and rear, which are fitted with a 'push-push' cover. The front storage compartment is located beneath the radio system, and the rear storage compartment is at the rear of the centre console.
Page 92 Chapter 3 3 16 KNOW YOUR VEHICLE ASHTRAY AND LIGHTER Ashtray and lighter option If required, your vehicle can be fitted with an ashtray and lighter instead of front and I or rear storage compartments. n11r HnlrlAn RAt:::l i iAr r.:::l n nrrlAr :::l n rl fit thA :::l � htr:::l \ 1 :::l n rl linhtAr fnr \/()II --·...
Page 93 Chapter 3 3-17 KNOW YOUR VEHICLE POWER SOCKET Power socket All vehicles have a power socket located inside the centre console. The power socket is operational when the ignition is turned to either on or accessories. Note: Any accessory device (mobile phone, car fridge etc.) connected to the power socket must not exceed a current draw of 10 amps.
Page 94 Chapter 3 3 18 KNOW YOUR VEHICLE CUP HOLDERS WARNING: Do not forget full cups when accelerating and braking! T o avoid spillage, it is recommended that any cups placed in the holders have lids. Cup holders are designed for holding standard size soft drink cans and smaller size bottles.
Page 95 The footrest for the driver's left foot is adjustable to three positions. First remove the caps and undo the two screws on the right hand side of the footrest. Move the footrest forward or backward as required, then replace the screws and caps. See your Holden Retailer for assistance with this adjustment if necessary.
Page 96: Driving
Driving Page 4 -2 Safety 4 -3 Engine starting Automatic transmission Manual transmission Anti-lock brake system 4- 9 Traction control 4 -11 Driving precautions 4-13 Add on equipment...
Page 97 Chapter 4 DRIVING SAFETY Before entering the vehicle Check that windows, mirrors and lights are clean. 2. Visually check tyre inflation (check with a pressure gauge each week). Before driving off Be sure that all doors are closed and secured. Position your seat for comfortable driving.
Page 98 Chapter 4 DRIVING ENGINE STARTING Ensure the park brake is firmly applied and release it only after you have started the engine and are ready to drive off. Manual: Press the clutch pedal and shift the gear lever to Neutral position. The clutch pedal can now be released.
Page 99 Chapter 4 DRIVING AUTOMATIC TRANSMISSION (if fitted) Floor mounted shift Push in the button on top of the transmission selector lever when shifting into any position indicated by the blue arrow. When the position of the transmission selector is changed, a large symbol is illuminated on the instrument panel centre display in conjunction with the PRND321 constant icon at the bottom of the display.
Page 100 Chapter 4 DRIVING AUTOMATIC TRANSMISSION Power I normal/ cruise mode The transmission operates in three modes: power, normal and cruise. Power mode h a s revised automatic transmission shift points, to give the vehicle a more responsive feel. Normal mode is recommended for normal or freeway driving, as it gives better fuel economy.
Page 101 Chapter 4 DRIVING AUTOMATIC TRANSMISSION This prevents the rear wheels from turning and so should be selected P (park) (together with the park brake) when leaving the vehicle. Never select P while your vehicle is still moving. The engine can be started in this nr'\citif"'\n tJV�I�IVII.
Page 102 Chapter 4 DRIVING MANUAL TRANSMISSION Shift patterns The shift pattern illustrated is also found on the top of the gear shift lever. When selecting Reverse gear you must shift the gear lever sideways against spring pressure in order to pass into the gear. Shift speeds Manual transmission change speeds The chart shows the recommended change...
Page 103 (@) warning light and 'ABS Fault' animation illuminate when driving, a malfunction of the Anti-lock Brake System is indicated and you should see your Holden Retailer. The vehicle's brake system will still operate conventionally, only the anti-lock operation is impaired.
Page 104 Chapter 4 DRIVING TRACTION CONTROL Traction control helps prevent the driving wheels rear from spinning. As soon as even one driving wheel starts to spin traction control reduces the power from the engine and applies the brakes, as necessary. This improves the vehicle's stability, particularly on snow and ice, as well as on wet or slippery roads.
Page 105 You should contact your Holden Retailer. Traction Pressing the T/C button again switches the system on, bringing up the 'Traction Ctrl On' Ctrl On animated display.
Page 106 Engine misfire Reduce speed and do not tow a caravan or trailer until the misfiring is corrected at the nearest Holden Retailer. Otherwise, the catalytic converter and exhaust system may overheat, resulting in vehicle damage. Brakes The power assisted brakes fitted to your vehicle use vacuum from the engine when it is running.
Page 107 Chapter 4 4-12 DRIVING DRIVING PRECAUTIONS cont. Loose articles Do not leave loose articles or luggage in the passenger compartment. Whenever possible, stow articles in the luggage compartment. WARNING: Gas cylinders can leak, creating a risk of fire or explosion. As a precaution, ensure adequate ventilation when carrying gas cylinders.
Page 108 Chapter 4 4-13 DRIVING ON EQUIPMENT Snow chains Due to lack of clearance, snow chains cannot be fitted to wheel and tyre configurations built with your vehicle. If your vehicle needs to be driven in the snow, the owner should consider changing the wheel and tyre configuration.
Page 109: Fuel
Fuel Page Fuel 5 -4 Emission control Reducing fuel consumption Measuring fuel consumption WARNING: The Monaro has NOT been designed f or conv ersion LPG. performance and safety of the ve hicle wou ld be seriously jeopardised (refer also 'Tra ction control' Cha pter 4).
Page 110 Take the vehicle to your Holden Retailer if you think your vehicle needs inspecting for any of the above reasons.
Page 111 Chapter 5 FUEL FUEL cont. Petrol - general Petrol tanks should always be filled at the intermediate or fast fill rate. Do not add any more petrol after the petrol filler first clicks off or petrol blows back- as this allows room for the petrol to expand inside the tank.
Page 112 Maintenance schedule of your vehicle's service booklet which is inside the glovebox of your vehicle. It is recommended that the necessary servicing be performed by an authorised Holden Retailer who has the specialised servicing equipment and trained personnel available to...
Page 113 Chapter 5 FUEL REDUCING FUEL CONSUMPTION Engine Maintain the engine in peak mechanical condition by having it serviced regularly in accordance with the Maintenance schedule in your vehicle's service booklet inside the glovebox of your vehicle. This will ensure items such as the spark plugs, air cleaner, engine idle speed etc.
Page 114 Chapter 5 FUEL MEASURING FUEL CONSUMPTION Before checking Fuel consumption should not be judged until the engine has been 'run-in'. You should wait at least 1500 km before checking fuel consumption. Please read information on the preceding page regarding fuel consumption. Find a petrol station and petrol pump that will be convenient to use for the next few tank fills.
Page 115 Chapter 5 FUEL NOTES...
Page 116: Emergencies
Emergencies Page Accidents Being involved Being a witness Medical assistance Flat tyre Towing a disabled vehicle 6-10 Fuses 6-12 Engine overheating 6-14 Flat battery 6-16 Airbags 6-19 Bulb replacement Note: Your new vehicle is covered for 3 years by 24 hour Roadside Assistance. Refer to Chapter 9 for details.
Page 117 Chapter EMERGENCIES ACCIDENTS All drivers are advised to learn what to do at the scene of an accident, particularly where people are injured. Injured people can choke to death if their air passages are not cleared, they can bleed to death unless the bleeding is stopped, they may require mouth-to-mouth resuscitation or may have to be moved, even though badly injured.
Page 118 Chapter 6 EMERGENCIES ACCIDENTS cont. Medical assistance This information is intended only as a guide to basic first aid and may not be applicable in all situations. You should always defer to a trained medical officer or other person with first aid knowledge.
Page 119 Chapter 6 EMERGENCIES FLATTYRE WARNING: Use the jack only for lifting the vehicle when changing wheels. Never get beneath the vehicle when it is only supported by the jack. Do not start or run the engine whi!e the vehicle is on!y supported by the jack. All passengers should be out of the vehicle when it is being jacked.
Page 120 Chapter 6 EMERGENCIES FLAT TYRE cont. Park on a hard, level surface, in a safe location, and set the park brake firmly. Turn the hazard warning flashers on. Remove the ignition key and place manual transmissions in Reverse gear or automatic transmissions in Park.
Page 121 Chapter 6 EMERGENCIES FLAT TYRE cont. Undo the nut in the centre of the spare wheel anticlockwise and lift the wheel out of the vehicle. The jack, combination jack handle I wheel wrench and nut cap tool (if fitted) are stored in a special container in the floor, which is under the spare wheel.
Page 122 Chapter 6 EMERGENCIES FLAT TYRE cont. If individual wheel nut caps are fitted, remove each nut cap individually, using the nut cap tool provided. Insert the nut cap tool into the nut cavity, squeeze the tool to grasp the nut cap and pull outwards to remove it. Put the nut caps together in a dry, clean place to avoid getting dirt inside the caps.
Page 123 Chapter 6 EMERGENCIES FLAT TYRE cont. 10. Raise the vehicle until the tyre is clear of the ground. Remove the wheel nuts and place together in a dry place to avoid getting dirt in the threads. Exchange the wheel on the vehicle with the spare wheel. Note: The tyres fitted to your vehicle may have an arrow on the tyre wall, showing the direction the tyre is designed to rotate when the vehicle is moving for..vard.
Page 124 Chapter 6 EMERGENCIES TOWING A DISABLED VEHICLE Towing a disabled vehicle Proper lifting or towing equipment is necessary when lifting or towing the vehicle to prevent damage. State laws must be followed. In an emergency, your vehicle may be towed on all four wheels in the following manner: Fit the towing equipment to the holes at the side of the front cross member.
Page 125 Chapter 6 6-10 EMERGENCIES FUSES The main fuse panel is in the instrument panel, below the steering column. Pull the hinged fuse panel down to reveal the fuses. Fuse layout diagram The separate, fuse I relay box is located in the engine compartment, marked 'Fuses'.
Page 126 Chapter 6 6-11 EMERGENCIES FUSES cont. BLOWER Cabin fuses and relays INHIBIT RELAY FLASHER UNIT � .SA) 20 (15A) (SPARE) TU N SIGNALS & RA 10, POWER LOCKS, SUB-WOOFER (20A) BACK UP LAMPS NAVIGATION & POWER WINDOWS AMPLIFIER CELL PHONE &...
Page 127 Chapter 6 6-12 EMERGENCIES ENGINE OVERHEATING WARNING: Immediate action is required if the engine overheats. This can be indicated by the temperature gauge needle moving over to the 'H' or the animated warning 'Engine Temp Hot' appearing on the central display (refer to Chapter 1 , by steam escaping from under the bonnet, loss of povver or...
Page 128 Chapter 6 6-13 EMERGENCIES ENGINE OVERHEATING cont. If, after carrying out one or more of the preceding actions the temperature gauge no longer signals an overheat condition, you can resume driving at a reduced speed. Return to normal driving after 1 0 minutes if the temperature gauge does not show an overheat condition once more.
Page 129 Chapter 6 6-14 EMERGENCIES FLAT BATTERY WARNING: DO NOT 'push start' or 'tow start' your vehicle, either manual or automatic. If unburnt fuel were to reach the catalytic converter and ignite, the converter could overheat or be destroyed by backfire. Therefore, if the battery is flat, you can 'jump start', but not 'push start' youi vehicle.
Page 130 Chapter 6 6-15 EMERGENCIES FLAT BATTERY cont. Attach one end of the RED jumper lead to the positive terminal of the booster battery (identified by a red colour, and the other end of the RED jumper lead to the positive terminal of the flat battery.
Page 131 6-16 Chapter 6 EMERGENCIES AIRBAGS Your vehicle is fitted with a driver's airbag, stored inside the steering wheel 'SRS AIRBAG' is stamped on the steering wheel and a label is attached under the driver's side sunvisor). Your vehicle also has a front passenger's airbag, stored in the dash panel.
Page 132 This is to indicate that the airbags are operational. If the light does not show when the ignition is switched on, or if it illuminates when driving, you should contact your Holden Retailer immediately, as the airbags and seat belt pretensioners may not function correctly in the event of an accident.
Page 133 AIRBAGS cont. The system should also be inspected by a Holden Retailer if the dashboard area or steering wheel is scratched, cracked or damaged, or if the front seats are damaged. Extensive design and testing has gone into the Holden airbag system. However, it should be treated with respect.
Page 134 Chapter 6 6-19 EMERGENCIES BULB REPLACEMENT Notes when replacing bulbs: Always turn off the related switch. It is important to fit only bulbs of the specified wattage. Do not touch new bulbs or reflectors with bare hands. Greasy fingers cause stains which evaporate, eventually resulting in a dull reflector.
Page 135 Chapter 6 6-20 EMERGENCIES BULB REPLACEMENT cont. Headlights - outboard low beam (55 Watts) H11 Open the bonnet. Refer to 'Front lights' previously described in this chapter for access instructions. Turn the outboard dust cap anticlockwise and remove from the rear of t he headlight assembly.
Page 136 Chapter 6 6-21 EMERGENCIES BULB REPLACEMENT cont. Headlights- inboard high beam (65 Watts) H9 Open the bonnet. Refer to 'Front lights' previously described in this chapter for access instructions. Turn the inboard dust cap anticlockwise and remove from the rear of the headlight assembly.
Page 137 Chapter 6 6-22 EMERGENCIES BULB REPLACEMENT cont. Front park lights (5 Watts) Open the bonnet. Refer to 'Front lights' previously described in this chapter for access instructions. Turn the inboard dust cap anticlockwise and remove from the rear of the headlight assembly.
Page 138 Chapter 6 6-23 EMERGENCIES BULB REPLACEMENT cont. Side turn signal (5 Watts) Grasp the lens at the rear, push forwards and pull away from the body of the vehicle. Separate the bulb holder from the lens assembly by first rotating the bulb holder anticlockwise.
Page 139 Chapter 6 6-24 EMERGENCIES BULB REPLACEMENT cont. Rear turn signal (21 Watts), stop I tail (21/5 Watts), reverse (21 Watts) Open the boot. Remove the two screws attaching the rear quarter light assembly to the body. Pull the rear auarter liaht assemblv sidewavs out from the oanel so that locatina oeas ..
Page 140 Install the dome lens and push back into place with your hand. Fog lights, instrument panel lights, vanity mirror lights, high mounted stop lights Bulb replacement for these light assemblies should be carried out by a Holden Retailer.
Page 141 Chapter 6 6-26 EMERGENCIES BULB REPLACEMENT cont. Footwell lights (2.7 Watts) Front footwell light bulbs are located on either side of the vehicle in the following locations: On the driver's side in the hinge panel assembly. On the passenger's side in the hush panel assembly.
Page 142 Chapter 6 6-27 EMERGENCIES NOTES...
Page 143 Weekly checks Page Miscellaneous checks Check locations Engine oil level Engine oil consumption Engine coolant level Automatic transmission level Washer fluid level Brake fluid level 7-10 Clutch fluid level 7-11 Power steering fluid level 7-12 Tyres 7-14 Battery 7-15 Trolley jack locations...
Page 144 Chapter 7 WEEKLY CHECKS MISCELLANEOUS CHECKS As well as taking your vehicle to be serviced (refer to service booklet in your vehicle's glovebox) there are a few simple, weekly checks that the owner I operator is recommended to make. These are shown on the following pages. WARNING: If the engine temperature is high, the cooling fan may remain on for several minutes after turning off the ignition.
Page 145 Chapter 7 WEEKLY CHECKS CHECK LOCATIONS Engine coolant ............page 7-6 Windscreen washer fluid .......... page 7-8 Brake fluid ..............page 7-9 Dipstick for automatic transmission (if fitted) ... page 7-7 Engine oil cap ............page 7-4 Dipstick for engine oil ..........page 7-4 Battery page 7-14 .
Page 146 Their use increases costs, may be detrimental to the operation of your vehicle and may void your New Vehicle Warranty, to the extent that Holden considers the non-recommended fluid to have affected the specifications or quality of your Holden vehicle.
Page 147 If, after taking into account the above factors, you are still concerned that your engine has excessive oil consumption then you should discuss the situation with a Holden Retailer. Remember that an engine's oil consumption should not be judged until it has run at least...
Page 148 If the coolant requires topping up, mix a solution of Holden coolant and clean fresh water in a container as per the ratio specified in Chapter 8 'Specifications'. Then, when the engine is cold, undo the cap and pour the fluid into the plastic tank.
Page 149 The level should NEVER read over the FULL HOT mark, so be careful not to add too much. If adding fluid, use only Holden specified automatic transmission fluid (refer to Chapter 8 for the correct specification). Add the fluid in the dipstick tube (the same...
Page 150 As washer fluid is constantly used the level should be topped up weekly. For a crystal clear windscreen, the correct amount of Holden washer fluid additive can be added (refer to Chapter 11 'Cleaning'). Do not use ordinary soap or detergent as these not only froth up but will also damage the wiper rubbers.
Page 151 Use only new brake fluid. Use of old, used or inferior brake fluid may endanger the functioning of the brake system. If the master cylinder requires constant topping up it could indicate that a fault exists and you should immediately see your Holden Retailer.
Page 152 Top up with heavy duty brake fluid (both the clutch system and the brake system use brake fluid) which meets Holden specifications (refer to Chapter 8 for the correct specification). Remember to replace the cap and clean up any spilled fluid.
Page 153 Do not over fill and remember to replace the cap tightly. If you often need to add fluid, you should see your Holden Retailer. Remember to secure the cap when the level is correct and clean up any spillage.
Page 154 Tyre condition is checked for you when you take your vehicle to be serviced by your • Holden Retailer, who is able to diagnose any unusual signs of wear. If the tyres are the balance The forward rotation direction of the...
Page 155 Out-of-balance wheels and tyres can cause annoying vibration and uneven tyre wear. If you suspect either of the above problems exist have a wheel alignment and balance check carried out by your Holden Retailer. Replacement and repair Replacing your factory fitted wheels and tyres with non-specified wheels and tyres may affect your warranty as well as your insurance policy.
Page 156 The fluid level of the battery will be checked for you when you take your vehicle to be serviced by your Holden Retailer. If your vehicle is operated in hot temperatures or at constant high speed the battery fluid level should be checked each month.
Page 157 Chapter 7 7-15 WEEKLY CHECKS TROLLEY JACK LOCATIONS You should always use the jack locations Trolley jack lifting points shown in Chapter 6 when using the original jack supplied with your vehicle. This jack has been designed to correctly and safely lift your vehicle, provided the warnings in Chapter 6 are observed.
Page 158: Specifications
Specifications Page 8- 2 Specifications Lubricants and fluids Power and torque Capacities General specifications Dimensions Body lubricants Identification labels...
Page 159 ""--· ·-· n,.,.v "'"""' Ill '� e>noorl\ L..I � /\IVIIx..;.t Ill\'-' �f"o'"''-"""'} IVIdiiUdl transmission fluid Heavy duty brake fluid, conforming to Holden Specification Brake and clutch fluid Number HN 1796 ( S uper DO T 4) Power steering fluid Dexron® Ill...
Page 160 NLGI No. 1 Lithium Grease (with Zinc Oxide) meeting Holden Specification HN 1225. Door hinge grease NLGI No. 1 Lithium Grease (with Zinc Oxide) meeting Holden Specification H N 1225. Check link housing NLGI No. 2 Polyurea Grease (mineral oil base) 1.2 g applied to housing.
Page 161 Chapter 8 SPECIRC'A 110NS /DENT/FICA TION LABELS Safety Compliance Plate (Australian vehicles) Shown on the plate are the vehicle Make, Model Series, Date of Manufacture, Vehicle Identification Number (VIN), approved seating capacity, Gross Vehicle Mass (GVM) on utility and Approval Number. Body and Option Plate This plate shows model identification, Vehicle Identification Number (VIN), paint and trim colour combination, air conditioning, paint number, engine, transmission, axie ratio...
Page 162 2 = active belts with driver and passenger airbags 3 = active belts with driver airbag 4 = active belts with driver, passenger and side airbags Body Style Code: 1 =Coupe Luxury Level: X= CV8 and CV8R Model Series: V = V2 World Manufacturer Identifier: 6G1 = Holden...
Page 163: After Sales
9-11 Z ealand Holden owners 9-12 Australian Holden Retailers 9-26 New Zealand Holden Retailers Note: The names and details of Retail Premises may change after the printing of this Handbook. The list contains both Authorised Holden Retailers Authorised Holden Service Operations.
Page 164 AFTER SALES NEW VEHICLE WARRANTY CERTIFICATE New Vehicle Warranty application This Warranty is given by Holden Ltd, ABN 84 006 893 232, CHolden'). The V'Jarranty applies to the vehicle identified on the inside front cover of the service booklet in your vehicle's glovebox.
Page 165 (d) use of incorrect types and grades of fuel, oil or lubricants (e) alteration of the vehicle by anyone not authorised by Holden (f) fitting of parts or accessories not recommended by Holden (g) any work carried out on the vehicle by anyone except an...
Page 166 Purchased at retail or trade • Parts and Accessories purchased at trade or retail and installed by other than a Holden Retailer or authorised Service Outlet are warranted for 1 year from the date of purchase. Please keep a receipt to support warranty claims.
Page 167 Vehicle Warranty) is required to enable your vehicle to be operated safely and it is not practical for you to go to an Authorised Holden Retailer, the service (to the extent that it is necessary to enable your vehicle to be operated safely) may be performed by any other qualified mechanic or repairer.
Page 168 WARRANTY QUESTIONS AND ANSWERS cont. Will I have to pay for maintenance costs during the Warranty Period? Maintenance costs are not covered by the Holden New Vehicle Warranty. The Maintenance Schedules in the service booklet (in your vehicle's glovebox) specify the minimum maintenance required for your vehicle operating under norma! conditions.
Page 169 Holden Retailer it is your responsibility to deliver your vehicle to the servicing Holden Retailer's premises. If, as a result of a defect which is covered by the Holden New Vehicle Warranty, your vehicle cannot be driven safely and you arrange for the nearest Authorised Holden Retailer to carry out the required Holden Warranty service, Holden will accept reasonable towing costs to move your vehicle to the nearest Holden Retailer's premises.
Page 170 Australia wide. We hope the need never arises, but if it does, we'll be there to help through Holden Roadside Assistance. How does Holden Roadside Assistance work?
Page 171 Holden Roadside Assistance stays with the vehicle, so if you sell your vehicle during the 36 month period, it is still eligible for the balance of the Holden Roadside Assistance. The new owner simply registers for the service by using the change of ownership form supplied in the Roadside Assistance booklet.
Page 172 Sales Manager or Service Manager- go to the General Manager or to the Retailer Principal. By now you should have satisfaction. If not, the Holden Customer Assistance office is at your disposal. The Holden Customer Assistance representatives can be telephoned from anywhere within Australia for only the cost of a local call.
Page 173 The information in this Owner's Handbook applies primarily to Australian Holden vehicles and there may be some differences to the Warranty and Owner Assistance provisions for New Zealand. Applicable details for New Zealand are set out in the Holden Warranty and Owner Assistance Information booklet enclosed in the New Zealand glovebox wallet.
Page 174 P: (02) 9904 1111 Fax: (02) 9904 1444 Heartland Holden DEE WHY & Cnr Glossop Harris Streets Peninsula Holden Dee Why P: (02) 9673 2111 Fax: (02) 9673 4932 & Cnr May Mooramba Roads P: (02) 9982 1311 Fax: (02) 9982 3755...
Page 175 Chapter 9 9-13 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. SUTHERLAND CASINO McGrath Holden Sutherland Quayside Motors 499-505 Princes Highway 142 Barker Street P: (02) 9545 4811 Fax: (02) 9545 2533 P: (02) 6662 2822 Fax: (02) 6662 2101 WAITARA CESSNOCK...
Page 176 Chapter 9 9-14 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. DUN GOG Turner Holden Royce Curtis Motors Park Street Lachlan Street Fax: (02) 6558 1108 (02) 6558 2317 (02) 6993 1503 Fax: (02) 6993 2212 EDEN HOLBROOK Ron Doyle Lieschke Motors Pty Ltd...
Page 177 (02) 4961 6485 (02) 6555 6644 (02) 6555 7433 Fax: Fax: NOWRA TWEED HEADS Glendon Motors Holden Von Bibra Twin Towns Holden 301-313 75-79 Princes Highway Pacific Highway (02) 4421 0144 (02) 4423 0854 (07) 5536 3411 (07) 5536 4490...
Page 178 P: (02) 4295 1223 Fax: (02) 4296 1007 WARREN Vic. Metropolitan Fuller Bros BACCHUS MARSH Dubbo Street Alan Mance Holden Bacchus March P: (02) 6847 4978 Fax: (02) 6847 4477 4 Graham Street WELLINGTON P: (03) 5367 4300 Fax: (03) 53674299 Gersbach's Garage Pty Ltd...
Page 180 Chapter 9 9-18 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. CAMPERDOWN HOPETOUN Camperdown Auto Parts Hopetoun Motors 96 Manifold Street 78 Lascelles Street P: (03) 5593 1983 Fax: (03) 5593 1979 P: (03) 5083 3143 Fax: (03) 5083 3290 CASTERTON HORSHAM...
Page 181 Chapter 9 9-19 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. ROCHESTER WARRAGUL Bruce Hocking Motors Pty Ltd Barry Bourke Warragul 85 Lowry Street 167 Queen Street P: (03) 5484 1455 Fax: (03) 5484 1140 P: (03) 5622 0000 Fax: (03) 5622 0333...
Page 182 Chapter 9 9-20 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. LAIDLEY BILOELA Buhse's Garage Andersons Auto City Spicer Street Dawson Highway (07) 5465 1406 Fax: (07) 5465 1706 (07) 4992 2833 Fax: (07) 4992 3066 MOOROOKA BOWEN McDeimott Holden John Sivyer Holden...
Page 183 Chapter 9 9-21 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. NOOSAVILLE HERVEY BAY Madill's Whitaker Holden Lot 1 Lionel Donovan Drive 96 Torquay Road P: (07) 5449 7900 Fax: (07) 5474 0073 P: (07) 4128 1722 PROSERPINE INGHAM Crossley Car Sales Whitsunday Pty Ltd...
Page 184 Chapter 9 9-22 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. ROSE PARK N.T. City Holden ALICE SPRINGS Kensington Road Peter Kittle Holden (08) 8334 4666 (08) 8334 4610 Fax: Stuart Highway SOMERTON PARK (08) 8952 5500 (08) 8953 0847 Fax: Hamilton Holden...
Page 185 Chapter 9 9-23 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. KINGSTON WAIKERIE LeCornu's Service Garage Riverside Holden Agnes Street 6 Crush Terrace P: (08) 8767 2424 Fax: (08) 8767 2533 P: (08) 8541 2900 Fax: (08) 8541 3325 LOXTON WHYALLA Flight Motors Pty Ltd...
Page 186 Chapter 9 9-24 AFTER SALES AUSTRALIAN HOLDEN RETAILERS cont. OSBORNE PARK COLLIE North City Holden Station Motors & Cnr Scarborough Beach Rd Harborne St 84 Throssell Street P: (08) 9273 2222 Fax: (08) 9273 2220 P: (08) 9734 1855 Fax: (08) 9734 1913...
Page 187 Chapter 9 9-26 AFTER SALES NEW ZEALAND HOLDEN RETAILERS GIS BORNE Auckland Metropolitan Enterprise Cars (1992) Limited GLENFIELD Gladstone Street Giltrap Holden Fax: (06) 867 8368 (06) 867 1280 Wairau Road GRACEFIELD (09) 444 8114 (09) 8008 Fax: Cable Price (NZ) Ltd...
Page 188 Chapter 9 9-27 AFTER SALES NEW ZEALAND HOLDEN RETAILERS cont. STRATFORD MORRINSVILLE Nicholson United Autos Ansford Johnson Limited Broadway Thames Street Fax: (06) 765 6119 Fax: (06) 765 7410 (07) 889 7042 (07) 889 3529 MOUNT MAUNGANUI TAUPO Transport Commercial (Tauranga)
Page 189 Chapter 9 9 28 AFTER SALES NEW ZEALAND HOLDEN RETAILERS cont. WHANGAREI Mark Cromie Holden 5-13 Hannah Street (09) 438 3199 (09) 438 3615 Fax:...
Page 190: Tow And Load 1
Tow and load Page 10-2 Towing 10-3 Towing equipment Loading the vehicle 1 0-4 1 0-5 Attaching a trailer 10-6 Towing and loading equipment 1 0-7 Towing precautions...
Page 191 Holden towing equipment is recommended where it is available. Where it is not available, no recommendation is made as to the make of equipment which should be used. Holden will not accept liability for defects occurring in towing equipment not marketed by Holden or for defects in the vehicle arising from the use of such equipment or for loss or injury caused by use of such equipment.
Page 192 Chapter 10 10-3 TOW and LOAD TOWING EQUIPMENT Essential Holden 1600 kg rated tow bar Essential Holden trailer wiring harness Up to 1600 kg Recommended A load distribution hitch is recommended if towing a single axle trailer that weighs more than 750 kg...
Page 193 ... ·-·-·,· However, do not exceed the maximum axle loads shown below in the diagram, including the weight of any fitted Holden approved accessories. If unsure, the vehicle should be weighed at a weighbridge. Remember that weight on a roof rack must be included in calculating the total load.
Page 194 Ensure the weight of the packed trailer is not greater than the towing capacity of your Holden approved tow bar package. Connect the trailer to the vehicle. Adjust load distribution hitch so that the vehicle and trailer are level with the ground (if towing a single axle trailer that weighs more than kg when loaded).
Page 195 Chapter 10 10-6 TOW and LOAD TOWING AND LOADING EQUIPMENT Load distribution hitch A load distribution hitch is recommended when towing more than 750 kg. • A load distribution hitch is designed to raise the rear of the vehicle and transfer a •...
Page 196 0.21 cc of fluid during braking. It must not be fitted to the front brake system, only to the rear brake system. While no recommendation is made by Holden with regard to the manufacturer of the brake system, the specifications issued by PBR indicate that their unit meets Holden requirements.
Page 197 Chapter 10 10-8 TOW and LOAD TOWING PRECAUTIONS cont. Running-in when towing It is recommended that you drive your new vehicle for at least 1500 km before towing. If you must tow before this do not exceed 80 km/h. The same applies if you have a new or reconditioned engine, transmission or rear axle.
Page 198 Chapter 10 10-9 TOW and LOAD NOTES...
Page 200: Cleaning
Chapter 11 11-2 CLEANING INTERIOR CLEANING WARNING: Many cleaners may be toxic, flammable or may damage the interior. When cleaning the interior, avoid volatile cleaners such as: acetone, lacquer thinners, enamel reducers, nail polish removers, or cleaners such as laundry soaps, bleaches or reducing agents.
Page 201 Do not bleach or dye seat belts as this may severely weaken them. Interior glass The interior glass area of the vehicle should be cleaned using Holden Glass Cleaner with a clean soft cloth. Care must be taken when cleaning inside the rear window so as not to damage the rear window demister or radio antenna.
Page 202 Fill a bucket with luke warm water and add no more than 2 capfuls of gentle detergent, such as Holden Hi Suds Car Wash. Do not use hot water, strong soap or chemical To remove bird droppings, soak with a wet sponge for several minutes before dissolved baking soda (Bicarbonate of Soda).
Page 203 Chapter 11 11-5 CLEANING EXTERIOR CLEANING cont. WARNING: Care should be taken when moving the vehicle after washing, in case water has affected the brakes. Applying the brakes lightly will indicate whether they have been affected. To dry them quickly, lightly apply the brakes while maintaining a slow forward speed with a clear area ahead, until brake performance returns to normal.
Page 204 However, the use of a good quality Polymer Glaze, such as Holden Quick and Easy Speed Finish, about every 3 months will reduce the effects of road bloom by removing natural contaminants which can build up on the paint.
Page 205 The blades can be cleaned by lifting them off the windscreen and cleaning with Holden Optikleen and a clean cloth.
Page 206 Chapter CLEANING CLEANING PRODUCTS DESCRIPTION USAGE PART SIZE NUMBER 92145132 Seals in a deep, lustrous glazed finish. Quick and Easy Long life protection from oxidation, salt Speed Finish and weather damage. 92145418 Quick and Easy Seals in a deep, lustrous glazed finish. Speed Finish Long life protection from oxidation, salt and weather damage.
Page 207 Chapter 11 11-9 CLEANING NOTES...
Page 208 INDEX Jump starting 6-14 ....... Battery saver 3-13 ........Bonnet .
Page 209 INDEX cont. Cruise control 1-47 Cigarette lighter 3-16 ............Cleaning, exterior 11-4 Distance calibration...
Page 210 INDEX cont. Engine 6-12 Fuel capacity ..........
Page 211 INDEX cont. Kerb weights 10-8 Identification labels ....... . . Body and option plate Keys .
Page 212 INDEX cont. Mirrors ..........3-11 Petrol ..........Rear view, auto day/night ...
Page 213 INDEX cont. Seats Temperature, outside 1-42 ..........
Page 214 INDEX cont. Turn signals Seat belt 1-12 ........Bulb replacement, front 6-22 Security...

HOLDEN MONARO V2 III 2003 Series Owner's Handbook Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HOLDEN MONARO V2 III 2003 Series

Summary of Contents for HOLDEN MONARO V2 III 2003 Series

Table of Contents