1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Tecra M3-105
  6. User manual

Toshiba Tecra M3-105 User Manual

Portable personal computer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TECRA M3
TOSHIBA
TECRA M3
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Tecra M3-105

Summary of Contents for Toshiba Tecra M3-105

  • Page 1 TECRA M3 TOSHIBA TECRA M3 Portable Personal Computer User’s Manual...
  • Page 2 Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Sonic RecordNow! is registered trademarks of Sonic Solutions. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.LINK is trademark and registered trademark of Sony Corporation.

  • Page 3: Working Environment

    Any consequences resulting from the use of this product in working environments that are not approved or the use is restricted are not the responsibility of TOSHIBA Corporation. The consequences of the use of this product in those working environments may be:...
  • Page 4 This product and the supplied accessories are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if accessories or cables not manufactured / distributed by TOSHIBA are connected or implemented. To avoid EMC problems in general, the following advice should be observed: Only CE marked accessories should be connected / implemented.
  • Page 5 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany Greece Portugal Spain Switzerland All other countries/regions Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.
  • Page 6 User’s Manual Description on Laser specification The optical disk drive such as CD-ROM drive, DVD-ROM drive, DVD-ROM&CD-R/RW drive, DVD Super Multi drive and DVD±R/±RW drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE...

  • Page 7: Table Of Contents

    TECRA M3 Table of Contents Preface Manual contents ............xv Conventions.
  • Page 8 Restoring the complete system ........3-12 Restoring TOSHIBA utilities and drivers ....... . .3-12...
  • Page 9 RecordNow! Basic for TOSHIBA ........
  • Page 10 Maximizing battery operating time........6-11 by TOSHIBA ......4-29 ®...
  • Page 11 TOSHIBA Password Utility ........
  • Page 12 Using the TOSHIBA Assist button........
  • Page 13 TOSHIBA support ........
  • Page 14 Table of Contents User’s Manual...

  • Page 15: Preface

    TECRA M3 Preface Congratulations on your purchase of the TECRA M3 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TECRA M3 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

  • Page 16: Conventions

    Preface Chapter 4, Operating devices: TOSHIBA Dual Pointing Device, USB floppy disk drive, Slim Select Bay modules, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs.

  • Page 17: Key Operation

    Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
  • Page 18 Preface xviii User’s Manual...

  • Page 19: General Precautions

    TECRA M3 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 20: Pressure Or Impact Damage

    5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to appendix A or visit www.pcsupport.toshiba.com on the Internet for details). User’s Manual...

  • Page 21: Copy Protection

    General Precautions CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shut- down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions.
  • Page 22 General Precautions xxii User’s Manual...

  • Page 23: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.

  • Page 24: Software

    Introduction Software Microsoft The following software is preinstalled: Microsoft Microsoft Internet Explorer TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA Dual Pointing Device utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool...

  • Page 25: Features

    Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in Some models of the computers carry Intel...
  • Page 26 Introduction AC adaptor Disks Hard disk drive USB floppy disk drive (optional) Computers in this series are configured with an optical media drive installed in the Slim Select Bay. The available optical media drives are described below. DVD-ROM drive The AC adaptor provides power to the system and recharges the batteries when they are low.
  • Page 27 DVD-ROM&CD-R/RW drive DVD Super Multi drive DVD±R/±RW drive (DVD Dual drive) User’s Manual Some models are equipped with a full-size, DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.

  • Page 28: Display Controller

    The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Graphics controller Keyboard Built-in TOSHIBA Dual Pointing Device Built-in Touch Pad Built-in AccuPoint Ports Parallel External monitor Universal Serial Bus (USB 2.0)
  • Page 29 Docking interface i.LINK™ (IEEE1394) Infrared Slots PC card ExpressCard SD card Multimedia Sound system Video-out jack (S-Video) Headphone jack Microphone jack User’s Manual This port enables connection of an optional Advanced Port Replicator III described in the Options section. This port enables high-speed data transfer directly from external devices such as digital video cameras.
  • Page 30 Introduction Communications Modem Bluetooth An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia.
  • Page 31 Wireless LAN The numerical values for display are the theoretical maximums for Wireless LAN standards. The actual values may differ. The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
  • Page 32 DVD-ROM&CD-R/RW drive, DVD Super Multi drive, DVD±R/±RW drive, secondary hard disk drive or secondary battery pack. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system. Connects an optional security lock to anchor the computer to a desk or other large object.

  • Page 33: Special Features

    Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist button TOSHIBA Presentation button Hot keys Display automatic power off HDD automatic power off System automatic...
  • Page 34 You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver. When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation and shuts down.
  • Page 35 Optical media drive power icon Hibernation Standby User’s Manual Use this to turn the power of the optical media drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off. If the optical media drive power is off, the disc tray will not open even if the eject button is pushed.

  • Page 36: Utilities

    InterVideo WinDVD. This software enables communication between remote Bluetooth devices. The TOSHIBA SD memory boot utility is a utility which can create SD memory card to a boot disk. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows. Click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Boot Utility.
  • Page 37 RecordNow! Basic for TOSHIBA TOSHIBA Assist TOSHIBA PC Diagnostic Tool TOSHIBA Mobile Extension TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to TOSHIBA Dual Pointing Device utility TOSHIBA Mic Effect User’s Manual You can create CD/DVDs in several formats...
  • Page 38 Introduction NVIDIA Rotation Settings TOSHIBA Password Utility Sound driver TOSHIBA Accessibility DLA for TOSHIBA TOSHIBA Hotkey Utility for Display Devices TOSHIBA SD Memory Card Format CD/DVD Drive Acoustic Silencer 1-16 This utility let you rotate the desktop by 0 and 180 easily.

  • Page 39: Options

    (PC2-4200) can easily be installed in the computer. An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.

  • Page 40: Slim Select Bay Options

    Introduction Wireless LAN Kit Bluetooth Kit Slim Select Bay options The following modules can be installed in the Slim Select Bay. All other modules are options. CD-ROM DVD-ROM DVD-ROM&CD-R/RW Refer to the DVD Super Multi DVD±R/±RW (DVD Dual drive) Slim Select Bay HDD adaptor (Black) Hard disk drive Slim Select Bay...

  • Page 41: Chapter 2 : The Grand Tour

    TECRA M3 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.

  • Page 42: Left Side

    The Grand Tour Infrared port Wireless communication switch Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off. Left side The following figure shows the computer’s left side. Cooling vents Parallel port Parallel port...
  • Page 43 Security lock slot i.LINK (IEEE1394) port ExpressCard slot ExpressCard eject button PC card slot PC card eject button Keep foreign objects out of the ExpressCard slot and PC card slot. A pin or similar object can damage the computer’s circuitry. SD card slot Keep foreign objects out of the SD card slot.

  • Page 44: Right Side

    The Grand Tour Right side The following figure shows the computer’s right side. Headphone jack Headphone jack Microphone jack Universal Serial Bus (USB 2.0) ports Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. Operation of all functions of all USB devices has not been confirmed.

  • Page 45: Back Side

    Back side The following figure shows the computer’s back side. Video-out jack Video-out jack Modem jack In case of a lightning storm, unplug the modular cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem.

  • Page 46: Underside

    The Grand Tour LAN active indicator (orange) DC IN 15V jack DC IN 15V Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery lock Slim Select Bay lock Slim Select Bay lock screw...
  • Page 47 Battery release latch Docking interface Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer's circuitry. A plastic shutter protects the connector. Slim Select Bay lock Be sure to lock the Slim Select Bay lock before you transport or carry the computer.

  • Page 48: Front With The Display Open

    Display hinge Microphone Display hinge TOSHIBA Assist Button TOSHIBA Presentation Button The front of the computer with the LCD panel open The display hinge holds the LCD display panel at easy-to-view angles. A built-in microphone lets you record sound into your applications.
  • Page 49 LCD screen Stereo speakers Touch Pad control buttons Touch Pad AccuPoint control buttons AccuPoint User’s Manual The LCD screen displays high-contrast text and graphics. The available resolution depends on the model. With XGA, you can change the resolution between 800 × 600 and 1024 × 768 pixels. With SXGA, between 800 ×...
  • Page 50 Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is "enabled". Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, features, for details on settings.

  • Page 51: System Indicators

    System indicators LEDs, next to icons, light when various computer operations are in progress. SD card DC IN SD card DC IN Power Battery Slim Select Bay User’s Manual Power Battery System indicators The SD card indicator glows green when the computer is accessing the SD card slot.

  • Page 52: Keyboard Indicators

    The Grand Tour Wireless communication Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.

  • Page 53: Usb Floppy Disk Drive (Optional)

    Arrow mode Numeric mode USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. USB connector Disk-In-Use Indicator USB connector Disk-In-Use Indicator This indicator lights when the floppy disk is being Floppy disk slot Eject button Check the Disk-In-Use indicator when you use the USB floppy disk drive.

  • Page 54: Optical Media Drives

    The Grand Tour The USB floppy disk drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 is operating. Do not set anything on top of the floppy disk drive. Optical media drives One of the following optical media drives is installed in the computer: DVD-ROM, DVD-ROM&CD-R/RW, DVD Super Multi and DVD±R/±RW...

  • Page 55: Cds

    CD-R discs can be written only once. The recorded data cannot be erased or changed. CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the ultra-speed CD-RW discs is maximum 24-speed.

  • Page 56: Dvd Super Multi Drive

    The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.

  • Page 57: Ac Adaptor

    AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. And the adaptor converts AC power to DC power and reduces the voltage supplied to this computer.
  • Page 58 Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.

  • Page 59: Getting Started

    TECRA M3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.

  • Page 60: General Conditions

    Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

  • Page 61: Seating And Posture

    Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level Foot rest Place your chair so that the keyboard is at or slightly below the level of your elbow.

  • Page 62: Work Habits

    Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
  • Page 63 Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.

  • Page 64: Opening The Display

    Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing.

  • Page 65: Turning On The Power

    Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the section in Chapter 6, Power and Power-Up Modes. After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 66: Turning Off The Power

    For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.

  • Page 67: Starting Hibernation

    3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5. Select the Setup Action window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.

  • Page 68: Standby Mode

    When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

  • Page 69: Restarting The Computer

    1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 70: Restoring The Preinstalled Software

    Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.

  • Page 71: Operating Basics

    Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices, USB floppy disk drive (optional), changing Slim Select Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on caring for your computer, floppy disks and CD/DVDs.

  • Page 72: Using The Accupoint

    Operating Basics Two buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.

  • Page 73: Replacing The Cap

    Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. One spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight 2.

  • Page 74: Using The Usb Floppy Disk Drive (Optional)

    Operating Basics Using the USB floppy disk drive (optional) An optional USB floppy disk drive connects to any of the computer’s USB ports. It accommodates 1.44-megabyte or 720-kilobyte floppy disks. Refer to Chapter 2, Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port.

  • Page 75: Changing Slim Select Bay Modules

    Before removing or inserting a second battery pack, turn off the computer’s power. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, this utility to change modules while the computer’s power is on.

  • Page 76: Inserting A Module

    Operating Basics 6. Grasp the optical media drive and slide it out. The optical media drive and other Slim Select Bay modules can become hot with use. Be careful when removing the module. Lock screw Optical media drive Inserting a module Insert the Slim Select Bay HDD adaptor as described below.

  • Page 77: Using Optical Media Drives

    Using optical media drives The text and illustrations in this section refer primarily to the optional media drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor.
  • Page 78 Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. 3. Lay the CD/DVD, label side up, in the disc tray. When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.

  • Page 79: Removing Discs

    4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the disc tray to close it. Press gently until it locks into place.

  • Page 80: How To Remove Cd/Dvd When The Disk Tray Will Not Open

    Operating Basics How to remove CD/DVD when the disk tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.

  • Page 81: Before Writing Or Rewriting

    Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.

  • Page 82: When Writing Or Rewriting

    Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. Always copy data from the HDD to the CD. Do not use cut-and-paste. The original data will be lost if there is a write error. Do not perform any of the following actions: Change users in the Windows XP operating system.

  • Page 83: Important Message (Dvd Super Multi Drive)

    Disclaimer (DVD±R/±RW drive) TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW/+R/+RW disc that may be caused by writing or rewriting with this product.

  • Page 84: Before Writing Or Rewriting

    Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 85 This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM) If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.

  • Page 86: When Writing Or Rewriting

    Operating Basics Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and data damage. CD-RW (Ultra Speed +) media is not available. If used, data may be lost or damaged. Write from the computer's HDD to the CD/DVD.

  • Page 87: Recordnow! Basic For Toshiba

    Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: DVD-Video cannot be created using RecordNow!. DVD-Audio cannot be created using RecordNow!. You cannot use RecordNow!'s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-RW or DVD+R/+RW disc.

  • Page 88: Data Verification

    3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).

  • Page 89: When Using Windvd Creator Platinum

    When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy. 1. Click start and select the Control Panel. 2.

  • Page 90: Important Information For Use

    Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video Log in with Administrator rights to use WinDVD Creator. Make sure that your computer is running on AC power when using WinDVD Creator.
  • Page 91 2. Before recording the video to DVD When you record to DVD disc, please use only discs recommended by the Drive manufacturer. Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD. Do not perform any of the following actions: •...

  • Page 92: Media Care

    Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.

  • Page 93: Sound System

    Sound System Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, “howling” may be heard under certain conditions.

  • Page 94: Mic Effect

    TOSHIBA Mic Effect will reduce these echoes generated on your computer. Form more information on using the TOSHIBA Mic Effect, refer to its help. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack.

  • Page 95: Properties Menu

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/Region in the Control Panel, the change may not take effect.

  • Page 96: Modem Selection

    Operating Basics Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode.

  • Page 97: Disconnecting

    If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: Modem speed is slow or communication is interrupted. Skips may occur in sound. Disconnecting To disconnect the internal modular cable, follow the steps below.

  • Page 98: Bluetooth Wireless Technology

    TOSHIBA strongly recommend the customer to enable the WEP function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™...

  • Page 99: Bluetooth Tm Stack For Windows By Toshiba

    Please refer also to the electronic information which is included with each software. This Bluetooth specification. TOSHIBA cannot confirm all compatibility among any PC products and/or other electronic devices using Bluetooth TOSHIBA mobile PCs. Release Notes related to the Bluetooth ®...

  • Page 100: Wireless Communication Indicator

    Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indicator off Indicator glows If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN. Open or click the following: start, Control Panel, System, Hardware, Device Manager, Network adapters, Intel ®...

  • Page 101: Connecting Lan Cable

    Connecting LAN cable To connect the LAN cable, follow the steps below. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.

  • Page 102: Cleaning The Computer

    Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 103: Heat Dispersal

    CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Performance...
  • Page 104 Operating Basics 4-34 User’s Manual...

  • Page 105: Chapter 5 : The Keyboard

    TECRA M3 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 106: Function Keys: F1

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

  • Page 107: Hot Keys

    Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay operate these keys.
  • Page 108 Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
  • Page 109 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.

  • Page 110: Fn Sticky Key

    Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 111: Windows Special Keys

    Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.

  • Page 112: Temporarily Using Normal Keyboard (Overlay On)

    The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.

  • Page 113: Generating Ascii Characters

    Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
  • Page 114 The Keyboard 5-10 User’s Manual...

  • Page 115: Chapter 6 : Power And Power-Up Modes

    TECRA M3 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
  • Page 116 Power and Power-Up Modes 2nd battery fully adaptor charged connected 2nd Battery partially charged or no charge No 2nd battery installed Main battery adaptor charge is above low battery connected trigger point Main battery charge is below low battery trigger point Main battery charge is exhausted...
  • Page 117 When the main battery is not charging. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a 2nd battery are installed, the computer does not shut down until the charge in both batteries is exhausted.

  • Page 118: Power Indicators

    Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the 2nd battery.

  • Page 119: Power Indicator

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.

  • Page 120: 2Nd Battery Pack (Option)

    Troubleshooting The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.

  • Page 121: Safety Precautions

    Safety precautions Mishandling of battery packs can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, which could result in death or serious injury, if you do not follow instructions. Warning: Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
  • Page 122 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.

  • Page 123: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

  • Page 124: Battery Charging Notice

    Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Battery type High capacity battery pack (8800mAh) Battery pack (4700mAh) 2nd battery pack (3600mAh) RTC battery The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.

  • Page 125: Monitoring Battery Capacity

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 126: Retaining Data With Power Off

    Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery type High-capacity battery pack (8800mAh) Battery pack (4700mAh) 2nd battery pack (3600mAh) RTC battery Extending battery life To maximize the life of your battery pack:...

  • Page 127: Replacing The Battery Pack

    Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.

  • Page 128: Installing The Battery Pack

    7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.

  • Page 129: Toshiba Password Utility

    ( Battery lock 6. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
  • Page 130 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...

  • Page 131: Supervisor Password

    Register, delete or change the supervisor password. Create or invalidate a supervisor password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. Specify restrictions for general users.

  • Page 132: Power-Up Modes

    Refer also to the sections in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.

  • Page 133: Chapter 7 : Hw Setup

    TECRA M3 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.

  • Page 134: Power On Display

    HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted (This setting is only available on Standard VGA mode and not available on...

  • Page 135: Boot Priority

    Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: CD-ROM CD-ROM CD-ROM CD-ROM CD-ROM CD-ROM You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: FDD is looked for when the boot disk is contained in external FDD.
  • Page 136 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN) boot.
  • Page 137 HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD 2nd HDD (Default) 2nd HDD Built-in HDD...
  • Page 138 HW Setup Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Disabled This function lets you set the CPU operating mode.

  • Page 139: Device Config

    Built-in LAN This feature enables or disables the Built-in LAN. Enabled Disabled Device Config Device Configuration This option lets you set the device configuration. All Devices Setup by OS PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration. Enabled Disabled Auto...
  • Page 140 HW Setup USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.

  • Page 141: Optional Devices

    TECRA M3 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC card ExpressCard SD card Memory expansion Power devices...

  • Page 142: Pc Card

    The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 143: Removing A Pc Card

    The computer is equipped with an ExpressCard slot that can accommodate a Type II card. Any ExpressCard that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports hot plug connection. This slot utilizes the PCI-Express interface that supports the reading and writing of data at data rates (bus specification for PC) of 2.5 Gbps (theoretical value) each.

  • Page 144: Removing An Expresscard

    Optional Devices 2. Press gently to ensure a firm connection. ExpressCard slot 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard. Removing an ExpressCard To remove the ExpressCard, follow the steps below.

  • Page 145: Sd Card

    SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.

  • Page 146: Removing An Sd Card

    Optional Devices 2. Press gently to ensure a firm connection. Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2.

  • Page 147: Sd Card Care

    8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the...

  • Page 148: Installing Memory Module

    Optional Devices Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a.The computer is turned on.
  • Page 149 4. One screw in the position which removed the battery pack is removed. Screw 5. Return to your computer to the upright position. 6. Slide the display latch on the front of the computer to the right and open the LCD display panel. 7.
  • Page 150 Optional Devices 9. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.

  • Page 151: Removing Memory Module

    11. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot.

  • Page 152: Battery Pack

    Optional Devices 4. Push the latches to the outside to release the memory module. A spring will force one end of the memory module up. 5. Grasp the sides of the module and pull it out, then replace the insulator. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot.

  • Page 153: Inserting

    Inserting To install the 2nd battery pack in the adaptor, follow the steps below. 1. Fit the side of the 2nd battery pack opposite the connector into the adaptor. 2. Lay the battery into the adaptor. The latch should close automatically to secure the 2nd battery pack.

  • Page 154: Battery Charger

    Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer.

  • Page 155: Installing The Hdd Pack

    8. Lift the HDD pack and remove it. Plastic tab Installing the HDD pack To install the HDD pack, follow the steps below. 1. Place the HDD into the space for HDD. Slide the HDD to connect to the connector. 2.

  • Page 156: Slim Select Bay Hdd Adaptor (Black)

    Optional Devices Slim Select Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an additional 40.0 billion bytes (37.26 GB), 60.0 billion bytes (55.89 GB), 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Slim Select Bay.

  • Page 157: Usb Floppy Disk Drive

    3. Close the lid and slide the lock to the lock position. For details on inserting the Slim Select Bay HDD adaptor in the computer’s Slim Select Bay slot, refer to Chapter 4, USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics.

  • Page 158: Using The Toshiba Assist Button

    You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, To use “TV OUT” function by “TOSHIBA Assist button”, it is necessary to change the settings of “TOSHIBA Assist button” in advance.

  • Page 159: Changing The Resolution

    If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. Click the Settings tab and click the Advanced button. d.

  • Page 160: I.link (Ieee1394)

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.

  • Page 161: Connecting

    Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: You may need to install drivers for your i.LINK devices.

  • Page 162: Advanced Port Replicator Iil

    Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator lll provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer.

  • Page 163: Parallel Printer

    6. Turn on the printer’s power. 7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK.

  • Page 164: Security Lock

    Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.

  • Page 165: Troubleshooting

    TECRA M3 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 166: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 167: Hardware And System Checklist

    Software Hardware Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas: System start-up Self test Power Password Keyboard Internal LCD display panel Hard disk drive DVD-ROM drive DVD-ROM&CD-R/RW drive DVD±R/±RW drive...

  • Page 168: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.

  • Page 169: Ac Power

    Computer shuts down and its DC IN indicator is flashing in green AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, for more information. Problem AC adaptor doesn’t power the computer (DC IN indicator does...
  • Page 170 If you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...

  • Page 171: Password

    5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Procedure Refer to the TOSHIBA Password Utility Chapter 6, Power and Power-Up Modes. Keyboard. Procedure Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.

  • Page 172: Internal Lcd Display Panel

    Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Problem No display Markings appear on the LCD screen. Problems above remain unresolved or other problems occur Hard disk drive Problem Computer does not boot from hard disk drive...

  • Page 173: Dvd-Rom Drive

    DVD-ROM drive For more information, refer to Chapter 4, Problem You cannot access a CD/ DVD in the drive Some CD/DVDs run correctly, but others do not User’s Manual Operating Basics Procedure Make sure the drive’s disc tray is securely closed.

  • Page 174: Dvd-Rom&Cd-R/Rw Drive

    Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Problem You cannot access a CD/DVD in the drive Some CD/DVDs run correctly, but others do 9-10 Operating Procedure Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on.

  • Page 175: Dvd±R/±Rw Drive (Dvd Dual Drive)

    User’s Manual Procedure If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.

  • Page 176: Dvd Super Multi Drive

    Chapter 2, The Grand Tour. If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.

  • Page 177: Usb Floppy Disk Drive

    Some CD/DVDs run correctly, but others do USB floppy disk drive For more information, refer to Chapter 4, Problem Drive does not operate There may be a faulty cable connection. Check Some programs run correctly but others do You cannot access the external 3 1/2"...

  • Page 178: Sd Card

    Troubleshooting SD card Refer also to Chapter 8, Problem SD card error occurs You cannot write to an SD memory card You cannot read a file PC card Refer also to Chapter 8, Problem PC card error occurs ExpressCard Refer also to Chapter 8, Problem ExpressCard error occurs...

  • Page 179: Infrared Port

    Device tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it.

  • Page 180: Usb Mouse

    Troubleshooting Problem Double-tapping (Touch Pad) or double- clicking (AccuPoint) does not work USB mouse Problem On-screen pointer does not respond to mouse operation Double-clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erratically 9-16 Procedure Try changing the double-click speed setting in...

  • Page 181: Usb

    Refer also to your USB device’s documentation. Problem USB device does not work Memory expansion Refer also to Chapter 8, memory modules. Problem Beep sounds. (Two beeps, a dash and a dot, for a defective memory module in slot A. Three beeps, a dash and two dots for slot B.

  • Page 182: Sound System

    Troubleshooting Sound system Refer also to documentation for your audio devices. Problem No sound is heard Annoying sound is heard External monitor Refer also to Chapter 8, documentation. Problem Monitor does not turn No display Display error occurs 9-18 Procedure Adjust the volume control dial.

  • Page 183: I.link (Ieee1394)

    i.LINK (IEEE1394) Problem i.LINK device does not function Modem Problem Communication software can’t initialize modem You can hear a dial tone but can’t make a call You place a call, but a connection can’t be made After making a call you can’t hear a ring Communication is cut off unexpectedly...

  • Page 184: Lan

    Troubleshooting Problem Character display becomes garbled during a communication You cannot receive an incoming call Problem Cannot access LAN Wake-up on LAN does not work Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Problem...

  • Page 185: Bluetooth

    Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Cannot access Bluetooth device Printer Refer also to the and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Printer does not turn on. Check that the printer is connected to an electric Computer/printer do not communicate Printer error...

  • Page 186: Tv Output Signal

    TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 187: Specifications

    TECRA M3 Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) Size Environmental Requirements Conditions Operating Non-operating Thermal Gradient Wet-bulb temperature Conditions Operating Non-operating User’s Manual Appendix A 2.26 kilograms, configured with: 14.1”XGA, 256MB RAM, 40GB HDD, DVD-ROM drive, modem, LAN (100M Bit), Wireless LAN, no Bluetooth antenna, 6cell battery pack.

  • Page 188: Built-In Modem

    Specifications Power Requirements AC adaptor Computer Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing Control command Monitor function Communication specifications Communication system Communication protocol Communication speed 100-240 volts AC 50 or 60 hertz (cycles per second) 15 VDC 5.0 amperes Telephone line (analog only)
  • Page 189 Transmitting level Receiving level Input/output impedance Error correcting Data compression Power supply User’s Manual -10 dBm -10 to -40 dBm 600 ohms ±30% MNP class 4 and ITU-T V.42 MNP class 5 and ITU-T V.42bis +3.3V (supplied by computer) Specifications...
  • Page 190 Specifications User’s Manual...

  • Page 191: Display Controller And Modes

    TECRA M3 Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA mods at internal LCD display panel. SXGA+ model supports SXGA and SXGA+ in addition to VGA, SVGA and XGA modes.
  • Page 192 Display Controller and Modes Video Type mode 0, 1 Text 2, 3 Text 0*, 1* Text 2*, 3* Text 0+, 1+ Text 2+, 3+ Text 4, 5 Grph Grph Text Text Table1 Video modes (VGA) Resolution Character matrix (pels) 40 × 25 8 ×...
  • Page 193 Table1 Video modes (VGA) continued Video Type mode Grph Grph Grph Grph Grph Grph Grph User’s Manual Resolution Character matrix (pels) 320 × 200 8 × 8 Pels 640 × 200 8 × 8 Pels 640 × 350 8 × 14 Pels 640 ×...
  • Page 194 Display Controller and Modes Table 2 Video modes (XGA model) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 ×...
  • Page 195 Table 2 Video modes (XGA model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
  • Page 196 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 ×...
  • Page 197 Table 3 Video modes (SXGA+ model) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
  • Page 198 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 ×...
  • Page 199 Table 3 Video modes (SXGA+ model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
  • Page 200 Display Controller and Modes B-10 User’s Manual...

  • Page 201: Wireless Lan

    TECRA M3 Wireless LAN Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol Data Rate Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless...

  • Page 202: Supported Frequency Sub-Bands

    Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.

  • Page 203: Wireless Ieee 802.11 Channels Sets (Revision A

    *1 Factory-set default channels When installing Wireless LAN cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.

  • Page 204: Wireless Channels Sets (Turbo Mode

    Wireless LAN Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID *3 These channels are available to Atheros A/B/G combo type only. Available Areas: US (USA, CANADA) only. 5580 5600 5620 5640 5660 5680...

  • Page 205: Bluetooth Wireless Technology Interoperability

    Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group.
  • Page 206 Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...

  • Page 207: Bluetooth Wireless Technology And Your Health

    Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

  • Page 208: Caution: Fcc Interference Statement

    In order to comply with FCC radio frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth TOSHIBA has to be operated while maintaining a minimum body to antenna which are located on top of LCD distance of 20 cm. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

  • Page 209: Taiwan

    Relevant transmitters include FCC IDs: CJ6UPA3375WL, CJ6UPA3232BT Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. Taiwan Article 14 Unless approved, for any model accredited low power radio...

  • Page 210: Using Bluetooth

    2. In case that RF interference occurs to Other Radio Stations from this equipment, please change promptly the frequency for use, place to use, or stop emitting Radio. 3. Please contact TOSHIBA Direct PC if you have a problem, such as interference from this equipment to Other Radio Stations.

  • Page 211: Device Authorization

    3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 Toll Free Tel Direct Dial Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business of Japan.

  • Page 212: Wireless Technology

    Do not use this equipment except in the countries/regions in the following table. Australia Canada Germany Japan New Zealand Switzerland Greece Portugal Countries/regions that have approved Bluetooth Card from TOSHIBA equipment is approved to the radio Austria Denmark Iceland Luxembourg Norway Italy Spain Belgium Finland Ireland...

  • Page 213: Certification Agencies

    TECRA M3 AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size:...
  • Page 214 AC Power Cord and Connectors For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.

  • Page 215: If Your Computer Is Stolen

    What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: Fill in the TOSHIBA Theft Registration form (or a copy of it) below. Attach a copy of your receipt showing where your computer was purchased.

  • Page 216: Toshiba Theft Registration

    If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g. 12345678G) Date stolen: Owner’s details Last name, first name: Company: Street: Postal Code/City:...
  • Page 217 TECRA M3 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
  • Page 218 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
  • Page 219 analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
  • Page 220 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
  • Page 221 compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 222 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 223 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 224 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 225 jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
  • Page 226 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
  • Page 227 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 228 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
  • Page 229 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
  • Page 230 Glossary Glossary-14 User’s Manual...
  • Page 231 2-17 CD-ROM drive 8-13 Cleaning the computer 4-32 Cooling vents 2-2 DC IN indicator 2-11 Display 1-6 DLA for TOSHIBA 1-16 Docking interface 1-7 Documentation list 1-2 Dual Pointing Device 1-6 8-14 4-28 DVD Super Multi drive 1-5 location 2-4...
  • Page 232 Index DVD±R/±RW drive (DVD Dual drive) 1-5 location 2-4 problems 9-11 using 4-7 writing 4-12 DVD-ROM drive 1-4 location 2-4 problems 9-9 using 4-7 DVD-ROM&CD-R/RW drive 1-5 location 2-4 problems 9-10 using 4-7 writing 4-10 Environment 3-1 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2...
  • Page 233 Index i.LINK 1-7 connecting 8-21 disconnecting 8-21 precautions 8-20 problems 9-19 Indicators 2-11 Infrared port 1-7 location 2-1 problems 9-15 Keyboard 1-6 emulating enhanced keyboard Fn Sticky key 5-6 Function keys F1...F12 5-2 hot keys 5-3 problems 9-7 typewriter keys 5-1 Windows special keys 5-7 Keypad overlay 1-11 Arrow mode 5-7...
  • Page 234 SD card 1-7 Security lock 1-17 Slim Select Bay 2-4 Soft keys Sound System 4-23 Self test 9-4 Sound system 9-18 support from TOSHIBA 9-22 System start-up 9-3 Touch Pad/AccuPoint 9-15 USB 9-17 USB floppy disk drive 9-13 Wireless LAN 9-20 4-17...
  • Page 235 TOSHIBA Controls 1-14 TOSHIBA Dual Pointing Device utility 1-15 TOSHIBA Mic Effect 1-15 TOSHIBA Mobile Extension 1-15 TOSHIBA PC Diagnostic Tool 1-15 TOSHIBA Power Saver 1-14 TOSHIBA Presentation button 1-11 TOSHIBA SD Memory Boot Utility 1-14 TOSHIBA Theft Registration F-2...
  • Page 236 Index Index-6 User’s Manual...

This manual is also suitable for:

Tecra m3-336Tecra m3-138Tecra m3-sp719Tecra m3

Table of Contents