1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Satellite M30
  6. User manual

Toshiba M30 User Manual

Portable personal computer
Hide thumbs Also See for M30:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
TOSHIBA
Satellite M30 Series
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba M30

Summary of Contents for Toshiba M30

  • Page 1 TOSHIBA Satellite M30 Series Portable Personal Computer User’s Manual...
  • Page 2 © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
  • Page 3 WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port,...

  • Page 4: Fcc Conditions

    Telephone: (949) 583-3000 EU Declaration of Conformity information TOSHIBA declares, that the product: PSM30* conforms to the following Standards: Supplementary Information: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
  • Page 5 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

  • Page 6: Region Selection

    Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made.
  • Page 7 FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 8 Instructions for IC CS-03 certified equipment The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
  • Page 9 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit.
  • Page 10 Notes for use of this device in New Zealand The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
  • Page 11 ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers.

  • Page 12: General Conditions

    General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.

  • Page 13: Optical Disc Drive Safety Instructions

    Optical disc drive safety instructions NOTE: Be sure to check the international precautions at the end of this section. CD-RW/DVD-ROM drives Panasonic UJDA750 CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
  • Page 14 DVD-R/-RW drives TOSHIBA SD-R6012 CAUTIONS: 1. The DVD-R/-RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 15 DVD Multi drives Panasonic UJ-811 CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 16 TEAC DV-W22E This product has been designed and manufactured according to FDA regulations “title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968,” and is classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective hous- ings.
  • Page 17 International precautions CLASS 1 LASER PRODUCT APPAREIL Å LASER DE CLASSE 1 LASER KLASSE 1 PRODUKT TO EN 60825-1 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER...
  • Page 18 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

  • Page 19: Table Of Contents

    Table of Contents Preface Manual contents ... xxvi Conventions ... xxvii Abbreviations ... xxvii Icons ... xxvii Keys ... xxvii Key operation ... xxviii Display ... xxviii Messages ... xxviii General Precautions Stress injury ... xxix Heat injury ... xxix Pressure or impact damage ...
  • Page 20 Back side ... 2-4 Underside ... 2-6 Front with the display open ... 2-7 Indicators ... 2-9 USB diskette drive ... 2-12 Optical media drives ... 2-13 Region codes for DVD drives and media ... 2-13 Writable discs ... 2-13 Formats ...
  • Page 21 Audio/Video controls ... 4-8 Mode control button ... 4-8 Controls for CD/DVD and Digital Audio ... 4-8 Next and Previous buttons ... 4-9 Play/Pause and Stop buttons ... 4-10 Audio ... 4-10 Writing CDs on CD-RW/DVD-ROM drive ... 4-12 Before writing or rewriting ... 4-12 When writing or rewriting ...
  • Page 22 Extending battery life ... 6-11 Replacing the battery pack ... 6-12 Removing the battery pack ... 6-12 Installing the battery pack ... 6-13 TOSHIBA Password Utility ... 6-14 User password ... 6-14 Supervisor password ... 6-16 Starting the computer by password ... 6-16 Power-up modes ...
  • Page 23 Hot keys ... 6-18 Panel power on/off ... 6-18 System Auto Off ... 6-18 Chapter 7 HW Setup Accessing HW Setup ... 7-1 HW Setup window ... 7-1 General ... 7-1 Parallel/Printer ... 7-2 Display ... 7-2 Boot Priority ... 7-2 Keyboard ...
  • Page 24 Sound system ... 9-20 Monitor ... 9-20 Modem ... 9-21 LAN ... 9-22 Wireless LAN ... 9-23 TV output signal ... 9-23 Printer ... 9-24 i.LINK (IEEE1394)... 9-25 TOSHIBA support ... 9-25 Before you call ... 9-25 Where to write ... 9-26 xxiv...
  • Page 25 Appendixes Appendix A Specifications ... A-1 Appendix B Display Controller and Modes ... B-1 Appendix C AT Commands ... C-1 Appendix D S-registers ... D-1 Appendix E V.90 ... E-1 Appendix F Internal Modem Guide ... F-1 Appendix G Wireless LAN ... G-1 Appendix H AC Power Cord and Connectors ...

  • Page 26: Preface

    This manual tells how to set up and begin using your Satellite M30 series computer. It also provides detailed information on configuring your computer, basic opera- tions and care, using optional devices and troubleshooting.

  • Page 27: Conventions

    Conventions Chapter 6, Power, gives details on the computer’s power resources and battery save modes. It also tells how to set passwords. Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, suggests courses of action if the computer doesn’t seem to be working properly.

  • Page 28: Key Operation

    User's Manual Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.

  • Page 29: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impaired performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 30: Pc Card Overheating

    For optimum performance, use your computer product only under recom- mended conditions. Read additional restrictions under in Appendix A, Specifications. Contact TOSHIBA Technical Service and Support for more information. Environmental requirements...

  • Page 31: Chapter 1 Introduction

    Carefully unpack your computer. Save the box and packing materials for future use. Hardware Check to make sure you have all the following items: Satellite M30 Series Portable Personal Computer Universal AC adaptor and power cord USB diskette drive (Provided with some models)

  • Page 32: Documentation

    If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple- mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer...
  • Page 33 Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The computer has an internal battery to back up the internal Real Time Clock (RTC) and calendar. Universal AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low.

  • Page 34: Pointing Device

    User's Manual DVD-R/-RW drive A full-size DVD-R/-RW drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
  • Page 35 Ports Parallel Parallel printer or other parallel device (ECP compatible). External monitor 15-pin, analog VGA port supports VESA DDC2B compat- ible functions. Universal Serial Bus The computer has three Universal Serial Bus ports that (USB 2.0) comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard.
  • Page 36 Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Software Standard Windows XP Home Edition/Professional operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk. Appendix E for technical informa-...

  • Page 37: Special Features

    Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
  • Page 38 You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernate item of the Power Save Mode window in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.

  • Page 39: Utilities

    This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme files. TOSHIBA Power Saver To access this power savings management program, open the Control Panel and select the TOSHIBA Power Saver icon.

  • Page 40: Options

    Standard battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High-capacity An additional battery pack can be purchased from your battery pack TOSHIBA dealer.

  • Page 41: Chapter 2 The Grand Tour

    The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. (1) M NDICATORS ODE CONTROL...

  • Page 42: Left Side

    User's Manual Infrared port This infrared port is compatible with Infrared Data Asso- (Infrared model ciation (IrDA 1.1) standards. It enables cableless 4 Mbps, only) 1.15 Mbps, 115.2 Kbps, 57.6 Kbps, 38.4 Kbps, 19.2 Kbps or 9.6 Kbps data transfer with IrDA 1.1 compatible external devices.

  • Page 43: Right Side

    Parallel port This Centronics-compatible, 25-pin parallel port is used to connect a parallel printer or other parallel device. This port supports Extended Capabilities Port (ECP) standard. PC card slot A PC card slot can accommodate one 5 mm Type II card. You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card.

  • Page 44: Back Side

    User's Manual Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automati- cally disabled. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.
  • Page 45 LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, Ether 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). The LAN has two indicators. See Chapter 4, CAUTIONS: 1.

  • Page 46: Underside

    User's Manual Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. ATTERY RELEASE LATCH Figure 2-5 The underside of the computer Memory module This cover protects two memory module sockets. One or cover two modules are preinstalled.

  • Page 47: Front With The Display Open

    TEREO SPEAKER LEFT OWER BUTTON YSTEM INDICATORS UTTONS NTERNET TOSHIBA C ONSOLE ICROPHONE IDEO OUT Figure 2-6 The front with the display open Display hinge The display hinge holds the display screen at easy-to- view angles. Display screen The LCD displays high-contrast text and graphics. The computer’s WXGA screen consists of 1280 x 800 pixels.
  • Page 48 TOSHIBA Console Press this button to launch an application automatically. button The default is TOSHIBA Console. S-Video out button Press this button to set your display device to TV (Video- out). Press it again to return to LCD. Touch Pad A Touch Pad located in the palm rest is used to control the on-screen pointer.

  • Page 49: Indicators

    Indicators The following indicators on the front of the computer can be monitored even when the display panel is closed. CD/DVD IGITAL Figure 2-7 System indicators CD/DVD The CD/DVD indicator glows blue when the computer is accessing a CD/DVD. Refer to Chapter 4, Basics, for details.
  • Page 50 User's Manual The following indicators are next to the keyboard under the display panel. CD/DVD INDICATOR INDICATOR CARD INDICATOR IRELESS COMMUNICATION SWITCH INDICATOR Disk The Disk indicator glows blue when the computer is accessing the built-in hard disk. CD/DVD The CD/DVD indicator glows blue when the computer is accessing a CD/DVD.
  • Page 51 The following indicators show the status of the display overlay. RROW MODE INDICATOR Figure 2-9 Keypad overlay indicators Arrow mode When the Arrow mode indicator lights blue, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keyboard.

  • Page 52: Usb Diskette Drive

    User's Manual USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. NDICATOR ISKETTE SLOT JECT BUTTON Figure 2-10 USB diskette drive Disk-In-Use This indicator lights when the diskette is being accessed. Indicator Diskette slot Insert diskettes in this slot.

  • Page 53: Optical Media Drives

    Optical media drives One of the following optical media drives is installed in the computer: CD-RW/DVD- ROM drive, DVD-R/-RW drive or DVD Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.

  • Page 54: Formats

    User's Manual DVDs DVD-R discs can be written only once. The recorded data cannot be erased or changed. DVD-RW discs can be recorded more than once. DVD-RAM discs can be recorded more than once. Formats The drives support the following formats: •...

  • Page 55: Dvd-R/-Rw Drive

    DVD-R/-RW drive The full- size DVD-R/-RW drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. NOTE: The read speed is slower at the center of a disc and faster at the outer edge.

  • Page 56: Universal Ac Adaptor

    Figure 2-11 The universal AC adaptor CAUTION: Use only the universal AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. 2-16...

  • Page 57: Chapter 3 Getting Started

    Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 58: General Conditions

    User's Manual General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

  • Page 59: Seating And Posture

    Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. ELOW EYE LEVEL OOT REST Figure 3-1 Posture and positioning of the computer...

  • Page 60: Lighting

    User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.

  • Page 61: Connecting The Universal Ac Adaptor

    CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. 1. Connect the power cord to the universal AC adaptor.

  • Page 62: Opening The Display

    User's Manual 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1.

  • Page 63: Starting Up For The First Time

    2. Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.

  • Page 64: Hibernation Mode

    NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 65: Starting Hibernation

    3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5. Select the Setup Action window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.

  • Page 66: Standby Mode

    Standby. 4. To prevent the computer from automatically entering Standby mode, disable Standby in TOSHIBA Power Saver. That action, however, will nullify the computer’s Energy Star compliance.
  • Page 67 2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility in the Control Panel.

  • Page 68: Restarting The Computer

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the up or down cursor key to select the CD/DVD-ROM Drive in the Boot Devices menu.

  • Page 69: Chapter 4 Operating Basics

    Operating Basics This chapter gives information on basic operations including using the Touch Pad, USB diskette drive (optional in some models), optical media drives, audio/video controls, modem, wireless communication features and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Touch Pad The computer is equipped with a Touch Pad as a pointing device.

  • Page 70: Using The Usb Diskette Drive

    User's Manual Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44- megabyte or 720-kilobyte diskettes. Refer to Chapter 2, information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-2.

  • Page 71: Disconnecting 3 1/2" Diskette Drive

    Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.

  • Page 72: Loading Discs

    User's Manual Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the eject button to open the drawer slightly. Figure 4-3 Pressing the eject button b.
  • Page 73 Using optical media drives 2. Grasp the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD...
  • Page 74 User's Manual NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6.

  • Page 75: Removing Discs

    Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-8. CAUTION: Do not press the eject button while the computer is accessing the optical media drive. Wait for the drive indicator to go out before you open the drawer.

  • Page 76: Audio/Video Controls

    User's Manual Audio/Video controls This section describes how to use the audio/video control buttons. You do not have to turn on the computer’s operating system to play audio CD/DVDs. The following controls let you use the computer as a stand-alone CD/DVD player. When the operating system is running, the buttons control video as well as audio.

  • Page 77: Next And Previous Buttons

    You cannot play optical media, only by setting the internal CD/DVD play drive on the Media Apps tab of the TOSHIBA Controls. 2. To play Digital Audio Data, you must set the play list in the Windows Media Player. The next time you play Digital Audio Data, the former play list will become active.

  • Page 78: Play/Pause And Stop Buttons

    User's Manual Play/Pause and Stop buttons A single button on a rocker controls the Play/Pause and Stop functions. Press on the icon to select the desired function. Play/Pause Press the Stop Press the Audio This section describes audio controls including sound levels and power manage- ment.
  • Page 79 Power management 1. Clicked the Advanced tab. 2. Select the Enable Power Management check box. 3. Input a time in Time to Power Saving State. NOTE: If the Enable Power Management check box is not selected, the audio controller always runs. Figure 4-9 Advanced window Sound quality Adjust the equalizer settings to enhance sound quality.

  • Page 80: Writing Cds On Cd-Rw/Dvd-Rom Drive

    User's Manual Feedback Your computer’s built-in microphone can be used to record monaural sounds into your applications and to issue voice commands to applications that support such functions. Since your computer also has built-in speakers, “feedback” may be heard under certain conditions.

  • Page 81: When Writing Or Rewriting

    TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufac- turers above. Operation of other media cannot be guaranteed. CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.

  • Page 82: Writing Cd/Dvds On Dvd-R/-Rw Drive

    NOTE: Also refer to the disc-writing instructions in the next section, Writing CD/DVDs on DVD Multi drive. Disclaimer TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product.

  • Page 83: Writing Cd/Dvds On Dvd Multi Drive

    DVD Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW/-RAM disc that may be caused by writing or rewriting with this product.

  • Page 84: Read/Write Function Chart

    PERATING User's Manual Read/write function chart Disc type CD-R Read Write Drag’n Drop CD+DVD*2 WinDVD Creator*2 DVD-Video*3 DVD VR*3 (DVD Video Recoding) *1 DVD Multi Drive: Yes. CD-RW/DVD-ROM and DVD-R/-RW Drive: No. *2 Software supplied with the product can be used for writing to a disc. *3 Video format can be written.
  • Page 85 Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.

  • Page 86: Before Writing Or Rewriting

    User's Manual You cannot overwrite data that has been previously written to a DVD-RW disc. You cannot partially delete any data written to a DVD-RW disc. Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. Data deleted (erased) from a CD-RW and DVD-RW/-RAM disc cannot be recovered.

  • Page 87: When Writing Or Rewriting

    Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. Writing with software other than Drag’n Drop CD+DVD, InterVideo WinDVD Creator 2 Platinum is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/RW or DVD-R/-RW/-RAM disc.
  • Page 88 User's Manual Do not use the DISC Backup function of Drag’n Drop CD+DVD to copy DVD- Video and DVD-ROM with copyright protection. DVD-RAM disc cannot be backed up with the DISC Backup function of Drag’n Drop CD+DVD. You cannot backup a CD-ROM or CD-R/RW to DVD-R/-RW using the DISC Backup function of Drag’n Drop CD+DVD.

  • Page 89: Data Verification

    Data verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Right-click Data BOX and select Options to display the DATA DISC Option window. 2. Mark the Record and Verify check box and select Byte compare. 3.

  • Page 90: Media Care

    User's Manual You will need 2 GB of empty hard disk space for every hour to write to a DVD- R/-RW disc. You cannot edit DVD-RAM video data that has copyright protection, using InterVideo WinDVD Creator 2 Platinum. Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes.

  • Page 91: Modem

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, Networking and click Modem Region Select. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 92: Properties Menu

    User's Manual 4. Select a region from the region menu or a telephony location from the sub- menu. • When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically. •...

  • Page 93: Connecting

    Dialing Properties Select this item to display the dialing properties. CAUTION: If you are using the computer in Japan, the Telecommunica- tions Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below.

  • Page 94: Wireless Lan

    User's Manual Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Se- quence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard (Revision A, B or G) and Turbo Mode. Supported features It supports the following features: Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36,...

  • Page 95: Security

    TOSHIBA strongly recommends that you enable the WEP function. TOSHIBA is not liable for damage resulting from unauthorized access to a Wireless LAN including, but not limited to, illegal intrusion, eavesdropping and loss or destruction of data.

  • Page 96: Lan

    User's Manual The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTIONS: 1. Do not install or remove an optional memory module while Wake-up on LAN is enabled.

  • Page 97: Disconnecting Lan Cable

    2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 4-12 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.

  • Page 98: Cleaning The Computer

    User's Manual Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 99: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum...
  • Page 100 User's Manual 4-32...

  • Page 101: Chapter 5 The Keyboard

    The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 102: F1 ... F12 Function Keys

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 103 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard.

  • Page 104: Hot Keys

    User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon.
  • Page 105 Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation.

  • Page 106: Fn Sticky Key

    Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 107: Windows Special Keys

    Keypad overlay Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the start menu and the other has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.

  • Page 108: Temporarily Using Normal Keyboard (Overlay On)

    User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without...

  • Page 109: Temporarily Using Overlay (Overlay Off)

    Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay.
  • Page 110 User's Manual 5-10...

  • Page 111: Chapter 6 Power

    Power The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether a universal AC adaptor is connected, whether a battery...

  • Page 112: Power Indicators

    User's Manual Table 6-1 Power conditions continued Battery • Operates adaptor charge is • LED: Battery off above low connected battery trigger point Battery • Operates charge is • LED: Battery below low battery trigger point Battery Computer goes charge is into resume mode exhausted shuts down...

  • Page 113: Dc In Indicator

    No light Under any other conditions, the indicator does not light. NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off.

  • Page 114: Real Time Clock Battery

    CAUTION: The computer’s RTC battery is a nickel metal hydride (NiMH) battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.

  • Page 115: Care And Use Of The Battery Pack

    Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
  • Page 116 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture.
  • Page 117 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.

  • Page 118: Charging The Batteries

    Hibernation mode (so you don’t lose data) and automatically turns off. NOTE: The computer enters Hibernate mode only if Hibernation is enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 119: Monitoring Battery Capacity

    Battery charging notice The battery may not charge right away under the following conditions: The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10°...

  • Page 120: Maximizing Battery Operating Time

    How you configure the computer (for example, whether you enable battery- power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: • Processor speed •...

  • Page 121: Retaining Data With Power Off

    Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Standard battery pack High-capacity battery pack RTC battery Extending battery life To maximize the life of your battery pack: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.

  • Page 122: Replacing The Battery Pack

    User's Manual Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.

  • Page 123: Installing The Battery Pack

    ATTERY PACK Figure 6-1 Releasing the battery pack CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below.

  • Page 124: Toshiba Password Utility

    4. Secure the battery safety lock. ATTERY PACK Figure 6-2 Securing the battery pack TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. NOTE: Passwords set in TOSHIBA Password Utility are different from the Windows password.
  • Page 125 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items:...

  • Page 126: Supervisor Password

    This utility lets you do the following: Register, delete or change the supervisor password. Create or invalidate a supervisor token NOTE: This function in the TOSHIBA Password Utility lets you invali- date only supervisor tokens or all tokens, including user and supervisor tokens.

  • Page 127: Power-Up Modes

    To enter a password manually, follow these steps: 1. Turn on the power as described in Chapter 3, message will be displayed: Figure 6-3 BIOS password window 2. Follow the on-screen prompts to enter the password. NOTE: If you enter the password incorrectly three times in a row, the computer shuts off.

  • Page 128: Windows Utilities

    User's Manual Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Hibernation. See Chapter 5, The Keyboard, for details. Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel.

  • Page 129: Chapter 7 Hw Setup

    HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Parallel/ Printer, Display, Boot Priority, Keyboard, CPU and LAN . Accessing HW Setup To run HW Setup, click start, click Control Panel and select TOSHIBA HW Setup.

  • Page 130: Parallel/Printer

    User's Manual About Click About to display the HW Setup version. Parallel/Printer This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Sets the port type to Extended Capabilities Port (ECP).
  • Page 131 HW Setup. 4. Support of PC (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. 5. A PC (ATA) card takes the position of HDD in the Boot Priority Options list, if the card is set up as the boot device in BIOS setup.

  • Page 132: Keyboard

    User's Manual Network Boot Protocol This feature sets the protocol to remotely boot from the network when Wake-up on LAN is enabled. Sets PXE as the protocol. (Default) [PXE] Sets RPL as the protocol. [RPL] NOTE: The Wake-up on LAN function consumes power even when the system is off.

  • Page 133: Lan

    Wake-up on LAN This features lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enables Wake-up on LAN. Enabled Disables Wake-up on LAN. (Default) Disabled CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled.
  • Page 134 User's Manual...

  • Page 135: Chapter 8 Optional Devices

    Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC cards SD cards Memory expansion Power devices Battery packs...

  • Page 136: Pc Cards

    The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 32-bit cards, including CardBus PC cards, which provide superior performance for the greater demands of multimedia.

  • Page 137: Removing A Pc Card

    Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.

  • Page 138: Sd Cards

    User's Manual SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory.

  • Page 139: Removing An Sd Card

    Removing an SD card To remove an SD card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. 4.

  • Page 140: Memory Expansion

    RAM. This section describes how to install and remove a memory module. CAUTIONS: 1. Use only memory modules approved by TOSHIBA. 2. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module.

  • Page 141: Installing Memory Module

    Installing memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. 2.

  • Page 142: Removing Memory Module

    User's Manual 5. Fit the memory module’s connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Figure 8-6 Seating the memory module CAUTIONS: 1. Be careful not to drop the screw inside the computer. 2.

  • Page 143: Battery Packs

    5. Grasp the module by the sides and pull it out. CAUTIONS: 1. If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.

  • Page 144: Usb Fdd Kit

    User's Manual USB FDD kit The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer.

  • Page 145: Changing The Resolution

    NOTE: If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. c. Click the Settings tab and click the Advanced button. d.

  • Page 146: I.link (Ieee1394)

    Make a backup of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data.

  • Page 147: Connecting

    If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. Make sure data transfer has ended or turn off the computer, before you: • Connect/disconnect an i.LINK device to/from the computer. •...

  • Page 148: Security Lock

    User's Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.

  • Page 149: Chapter 9 Troubleshooting

    Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 150: Analyzing The Problem

    User's Manual Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.

  • Page 151: Hardware And System Checklist

    Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.

  • Page 152: Self Test

    If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.

  • Page 153: Overheating Power Down

    Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem Procedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on. flashes orange If the computer is still too warm, the DC IN indicator will continue blinking when you turn on...
  • Page 154 User's Manual Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicators and battery operation see Chapter 6, Power. Problem Procedure Battery doesn’t The battery may be discharged. Connect the power the computer universal AC adaptor to charge the battery.

  • Page 155: Password

    Battery doesn’t Check the power consumption settings in power the computer TOSHIBA Power Saver Utility. Consider using a as long as expected power saving mode. RTC Battery Problem Procedure The following message is displayed: 0250: RTC battery is low 0251: CMOS checksum is inconsistent The RTC battery 1.

  • Page 156: Keyboard

    User's Manual Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, Keyboard. Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F10 and try typing again. Output to screen Make sure the software you are using is not is garbled...

  • Page 157: Hard Disk Drive

    Problems above Refer to your software’s documentation to remain unresolved determine if the software is causing the or other problems difficulty. occur Contact your dealer if the problems continue. Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM is in the optical media drive.

  • Page 158: Cd-Rw/Dvd-Rom Drive

    User's Manual CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.

  • Page 159: Dvd-R/-Rw Drive

    Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...
  • Page 160 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...

  • Page 161: Dvd Multi Drive

    • Do not connect/ disconnect external devices or If problems persist, contact your dealer. DVD Multi drive For more information, refer to Chapter 4, Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed.
  • Page 162 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...

  • Page 163: Diskette Drive

    Diskette drive For more information, refer to Chapter 4, Problem Procedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive. You cannot access Try another diskette. If you can access the the external 3 1/2"...

  • Page 164: Pc Card

    User's Manual PC card Refer also to Chapter 8, Optional Problem Procedure PC card Reseat the PC card to make sure it is error occurs firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.

  • Page 165: Pointing Device

    Pointing device If you are using a USB mouse, also refer to the your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume Pad operation its normal shape and try again to move it.

  • Page 166: Usb Mouse

    User's Manual USB mouse Problem Procedure On-screen pointer does not respond to shaped as an hourglass, wait for it to resume mouse operation Make sure the mouse is properly connected to the USB port. Double-clicking Try changing the double-click speed setting in does not work the mouse control utility.

  • Page 167: Usb

    Refer also to your USB device’s documentation. Problem Procedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documenta- tion for information on checking the drivers.

  • Page 168: Sound System

    User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Annoying sound You may be experiencing feedback.

  • Page 169: Modem

    Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Modem Refer to Appendix C and D. Problem Procedure Communication Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem software can’t initialize modem Properties in the Control Panel.

  • Page 170: Lan

    User's Manual A CONNECT display Check the error control setting in your is quickly replaced by communications application. NO CARRIER You can also use the AT\N command. Refer to Appendix C, Character display In data transmission, make sure the parity bit becomes garbled and stop bit settings correspond with those during a...

  • Page 171: Wireless Lan

    Wireless LAN If the following procedures do not restore LAN access, consult your LAN adminis- trator. For more information on wireless communication, refer to Chapter 4, Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist, contact your LAN administra- tor or dealer.

  • Page 172: Printer

    User's Manual Printer Refer also to the Parallel printer the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn on. outlet. Make sure the outlet is supplying power Computer/printer do not communicate Printer error 9-24 sections in Chapter 8, Optional Devices, and to...

  • Page 173: I.link (Ieee1394)

    If problems persist, contact your dealer. TOSHIBA support If you require any additional help using your computer or if you are having prob- lems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 174: Where To Write

    User's Manual Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W.

  • Page 175: Specifications

    Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight 2.81 kilograms Size 360 (w) x 270 (d) x 25.4/35.9 (h) millimeters (not including parts that extend beyond the main body) Environmental Requirements Ambient Conditions temperature Operating 5°C (41°F) to 35°C (95°F) Non-operating -20°C (-4°F) to 65°C (149°F) Thermal Gradient...
  • Page 176 User's Manual Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: system Fax: Communication Data protocol ITU-T-Rec...

  • Page 177: Appendix B Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Wide Extended Graphics Array (WXGA) support for the internal LCD and external monitors.

  • Page 178: Video Modes

    User's Manual Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
  • Page 179 Table1 Video modes (VGA) continued Video Type Resolution mode 320 x 200 Grph Pels 640 x 200 Grph Pels 640 x 350 Grph Pels 640 x 350 Grph Pels 640 x 480 Grph Pels 640 x 480 Grph Pels 320 x 200 Grph Pels Character LCD...
  • Page 180 User's Manual Table 2 Video modes (WXGA) Resolution colors 640 x 480 256/256K 800 x 600 256/256K 1024 x 768 256/256K 1280 x 800 256/256K 1280 x 1024 256/256K (Virtual) 1600 x 1200 256/256K (Virtual) 1920 x 1440 256/256K (Virtual) 2048 x 1536 256/256K (Virtual)
  • Page 181 Table 2 Video modes (WXGA) continued Resolution colors 640 x 480 64K/64K 800 x 600 64K/64K 1024 x 768 64K/64K 1280 x 800 64K/64K 1280 x 1024 64K/64K (Virtual) 1600 x 1200 64K/64K (Virtual) 1920 x 1440 64K/64K (Virtual) 2048 x 1536 64K/64K (Virtual) NOTE: Some video modes do not support multimonitor display.
  • Page 182 User's Manual Table 2 Video modes (WXGA) continued Resolution colors 640 x 480 16M/16M 800 x 600 16M/16M 1024 x 768 16M/16M 1280 x 800 16M/16M 1280 x 1024 16M/16M (Virtual) 1600 x 1200 16M/16M (Virtual) 1920 x 1440 16M/16M (Virtual) 2048 x 1536 16M/16M...

  • Page 183: At Commands

    AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command.
  • Page 184 User's Manual Answer command This command instructs the modem to go off-hook and answer an incoming call. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
  • Page 185 Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the...
  • Page 186 User's Manual Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume. Low volume. (Same as L0) Medium volume (default). High volume. Result Codes: n=0,1,2,3 ERROR Otherwise Monitor speaker mode This command turns the speaker on or off. The speaker is off.
  • Page 187 Result Codes: n=0,1 ERROR Otherwise Return online to data mode Instructs the modem to exit online command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to online data mode. This command issues a rate renegotiation before returning to online data mode.
  • Page 188 User's Manual Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
  • Page 189 Enable Enable Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
  • Page 190 User's Manual &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: n=0,1 ERROR Otherwise &Dn DTR control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal.
  • Page 191 &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
  • Page 192 User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
  • Page 193 Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects.
  • Page 194 User's Manual Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed.
  • Page 195 S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
  • Page 196 User's Manual Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
  • Page 197 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII Command line editing character (user defined)
  • Page 198 User's Manual Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
  • Page 199 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14...
  • Page 200 User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC* CONNECT 4800 EC* CONNECT 9600 EC* CONNECT 14400 EC* CONNECT 19200 EC*...
  • Page 201 Result Code DELAYED* BLACKLISTED* BLACKLIST FULL* *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
  • Page 202 User's Manual...
  • Page 203 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 204 User's Manual Table E-1 Result codes for a V.90 connection Result code CONNECT 32000 EC* CONNECT 36000 EC* CONNECT 40000 EC* CONNECT 44000 EC* CONNECT 48000 EC* CONNECT 52000 EC* CONNECT 56000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 37333 EC*...
  • Page 205 *EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 206 User's Manual...

  • Page 207: Appendix F

    Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for informa- tion only.
  • Page 208 User's Manual Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4.

  • Page 209: Card Specifications

    Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications Form Factor Mini PCI TypeIII Compatibility Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance.
  • Page 210 Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
  • Page 211 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. When installing Wireless LAN Cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
  • Page 212 User's Manual Wireless Channels Sets (Turbo Mode) Channel ID Frequency Range 5150-5850 MHz *: Available Area: US (USA, CANADA) only 5210 5250 5290 5760 5800 Note US only US only US only US only US only...

  • Page 213: Ac Power Cord And Connectors

    AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size: Current rating:...

  • Page 214: Usa And Canada

    User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada UL approved CSA approved Australia AS approved United Kingdom BS approved Europe Approved by the appropriate agency...

  • Page 215: Parts Numbers

    Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, communication and graphics devices.
  • Page 216 User's Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice.
  • Page 217 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only...
  • Page 218 adaptor (Abbreviations continued) ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array adaptor: A device that provides an...

  • Page 219: Cache Memory

    asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. backup: A duplicate copy of files kept as a spare in case the original is destroyed.
  • Page 220 capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB.

  • Page 221: Dialog Box

    configuration: The specific compo- nents in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration. control keys: A key or sequence of keys you enter from the keyboard to initiate a particular function within a program.

  • Page 222: Disk Drive

    disk drive disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head.
  • Page 223 (FDD): An electro- mechanical device that reads and writes to floppy disks. See also diskette. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. hardware folder: An icon in Windows used to store documents or other folders.
  • Page 224 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 225 keyboard: An input device contain- ing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmit- ted code is, in turn, representative of the (ASCII) character marked on the key.
  • Page 226 motherboard motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
  • Page 227 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A...
  • Page 228 A Class A device is sufficient for office use. Class B provides a more stringent classifica- tion for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
  • Page 229 Touch Pad: A pointing device integrated into the TOSHIBA com- puter palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switch- ing transistors for gates and storage.
  • Page 230 Glossary-14...
  • Page 231 Index AC adaptor, See Universal AC adaptor ASCII characters 5-9 AT commands Appendix C Audio/Video control buttons 1-5, 2-1, location 2-1 Battery automatic hibernation 1-8 charging 6-8 extending life 6-11 indicator 2-9, 6-2 location 2-4 monitoring capacity 6-9 real time clock 1-3, 6-4 safety precautions 6-5 save mode 1-8 saving power 6-10...
  • Page 232 User's manual DVD Video Player 1-9 Environment 3-1 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory Fn + Ctrl (enhanced keyboard simula- tion) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4...
  • Page 233 Keyboard 1-4, 5-1 emulating enhanced keyboard 5-2 F1 … F12 function keys 5-2 Fn Sticky key 5-6 hot keys 5-4 problems 9-8 typewriter keys 5-1 wakeup 7-4 Windows special keys 5-7 Keypad overlay 1-8, 5-7 arrow mode 5-7 numeric mode 5-8 temporarily using normal keyboard (overlay on) 5-8 temporarily using overlay (overlay...
  • Page 234 PC card 9-16 power 9-4 printer 9-24 RTC battery 9-7 SD card 9-15 self test 9-4 sound system 9-20 support from TOSHIBA 9-25 system start-up 9-3 Touch Pad 9-17 TV output signal 9-23 USB 9-19 Wireless LAN 9-23 Processor 1-2, 7-4...
  • Page 235 Specifications Appendix A S-registers Appendix D Standby 1-7 automatic 1-8 setting 3-10 System indicators, See indicators TOSHIBA Controls 1-9 TOSHIBA Password Utility 1-10, See also Password TOSHIBA Power Saver 1-9 Touch Pad 1-4, 2-8 control buttons 2-8 location 2-7 problems 9-17...
  • Page 236 User's manual Index-6...

This manual is also suitable for:

Psm30c-0qq31Psm30c-0ruu9Psm30c-7101uPsm33c-00100ePsm33c-ysj00eSatellite m30 series ... Show all

Table of Contents