IMPORTANT – Please Read and Follow! • Make sure that incoming voltage is the Your safety and the safety of others is same as unit rating. An electric rating very important. plate specifying voltage, frequency, wattage, amperage, and phase is attached We have provided many important safety to the product.
Page 4
• The required use of a GFI is normally related to the location of a receptacle with respect to any signifi cant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Page 5
IMPORTANT – Please Read and Follow! It is your responsibility to: • comply with installation specifi cations and dimensions. • properly install unit. • remove any moldings or decorative panels that prevent the unit from being serviced. • make sure that you have these materials (not provided with your unit), which are necessary for proper installation: •...
Dimensions (Side-By-Side) 42” Side-By Side 3 – 1 9 / 3 2 ” ( 9 . 1 c m 48” Side-By Side 3 – 1 9 / 3 2 ” ( 9 . 1 c m 8 ” – 7 / ( 6 0 8 ”...
Page 7
Specifi cations (Side-By-Side) 42” Side-By-Side Description VCSB/CVCSB Overall width 42” (106.7 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth from rear To front edge of side trim: 23-3/4 (60.3 cm) To front of top grille: 26-1/4” (66.7cm) To front of handle endcap: 29-3/16”...
Dimensions (Flush Mount Trim and Custom Door Overlay) 42” Side-By Side with Flush Mount Trim 3 – 1 9 / 3 2 ” 48” Side-By Side ( 9 . 1 c m with Flush Mount Trim 3 – 1 9 / 3 2 ”...
Page 9
Specifi cations (Flush Mount Trim and Custom Door Overlay) 42” Side-By-Side Flush Mount Trim and Custom Door Overlay Description VCSB/CVCSB Flush Mount FDSB/CFDSB Overall width 42” (106.7 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth from rear To front edge of side trim: 25-1/2"...
Anti-Tip Dimensions 42” Side-By-Side Anti-Tip Location One 2”x 4” Mounting Board 3” (7.6 cm) x 3-1/2” (8.9 cm) 1 . 5 ” ( 3 . 8 c 7 9 – 3 / 8 ” ( 2 0 1 . 6 c m ) m i n t o b o t t o m...
Cabinet Information For installation in 24" (61.0 cm) deep cabinets, the door face protrudes 2-3/4” (7.0 cm) from the cabinet face. The handle protrudes an additional 2-15/16” (7.5 cm) into the room. Standard Mount Installation 1/4” (0.6 cm) 42” (106.7 cm) Finished 48”...
Custom Door Panel Installation Remove handle side cabinet screws and trim Remove all screws from handle side door trim. with a Phillips screwdriver. Remove two screws from top and bottom door trim. Remove handle side door trim. 2-1/16” 2-1/16” 1-11/16” 1-11/16”...
Page 20
Custom Door Panel Installation Slide custom wood panel to the hinge side, ensuring Reinstall handle side door trim “Z” bracket engages the door bracket. and door trim screws. Reinstall cabinet trim and screws.
48” Custom Panels Headline General Information Area Requirements A 115 volt, 60-Hz, 15 amp, fused, electrical Verify the following: supply is required. It is required that a separate • Unit can fi t into residence and can be circuit serving only this appliance be provided. moved around corners and through This appliance is equipped with a power supply doorways.
Page 22
Water Supply Requirements behind the unit. Use only 1/4” (6 mm) copper tubing for water • The installation of Viking Range units with a line. DO NOT install copper tubing reverse osmosis system is acceptable as in area where temperatures drop below 35º...
Headline General Information Area Requirements Tip Over Hazard • Most of the unit’s weight is at the top. Appliance is top heavy and tips easily when not Extra care is needed when moving the unit completely installed. Keep doors closed until to prevent tipping.
Headline Flush Mount Side Trim Installation (Sold Separately) Note: If the unit is to be installed fl ush with the Step 3 - Align the top of the fl ush mount cabinets, the fl ush mount side trim must be side trim with the top of the unit's machine installed fi rst.
Installation Headline Hinge Adjustment Front of unit Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Retighten four hinge screws. Anti-Tip Installation Wall 2 x 4 Refrigerator Replace unit top. Replace four side screws. Attach one 2 x 4 to wall stud (refer to dimensions page for exact location).
Page 26
Installation Headline Place unit within 3” (7.6 cm) of being fl ush with cabinets. Carefully move unit until semi fl ush with cabinet (depending Note: To avoid cabinet damage, place cardboard on unit). between cabinets and unit. When moving unit, DO NOT crimp, kink or crush water supply line.
Installation Headline Screw Wall 2 x 4 Refrigerator Lift unit off rollers to desired height and level unit using a Insert mounting screws into 2x4 attached to wall stud 5/16” head wrench. NOTE: DO NOT use an electric device. Overtightening can cause damage. Make sure evaporator pan is in correct location.
Headline Door Stop Adjustment 90˚ 110˚ 120˚ Open refrigerator door so door stop and shoulder Remove shoulder screw and place in 90º or screw are accessible. Note: Shoulder screw should be 120º position. in 110º door opening position.
Final Installation Headline Replace top air grille. Using an 8” (20.3 cm) magnetic nut driver, replace the two 1/4” (0.6 cm) screws. Replace the center grille louver. Open door. The display should fl ash. Press “ACTIVATE CONTROLS” pad and close door. Note: There is a 6 minute delay before the unit starts.
Headline Performance Checklist —Verify cabinet size. — Verify electrical supply and water supply (if applicable). — Install anti-tip device(s) and verify unit is secure. — Position unit in cutout, level at desired height and secure unit. —Plug-in unit and verify operation. —Connect water supply (if applicable).
Headline Verify Operations Control Panel Side-by-Side FREEZER REFRIGERATOR MAX FRZ MAX REF DOOR OPEN ACTIVATE FAST ALARM DISPLAY HIGHER LOWER CONTROLS TEMP TEMP COOL FAST COOL POWER SAB SHOW HIGH TEMP Press “ACTIVATE CONTROLS” pad. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A.
• Name of dealer from whom purchased Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to:...