Viking 5 Series Installation Manual
Side-by-side refrigerator/freezer
Hide thumbs
Also See for 5 Series:
Related Manuals for Viking 5 Series
Summary of Contents for Viking 5 Series
- Page 1 Installation GUIDE 5 SERIES Side-by-Side Refrigerator/Freezer VCSB5423 / VCSB5483 / FDSB5423 / FDSB5483 CVCSB5423 / CVCSB5483 / FDSB5423 / CFDSB5483...
-
Page 2: Table Of Contents
Table of Contents Warnings and Important Information _______________________________________________3 Tipping and Door Swing _________________________________________________________5 Dimensions & Specifi cations (Professional 42” & 48”) __________________________________ 8 Dimensions & Specifi cations (Professional 42” & 48” with fl ush mount trim) _________________________________________________________10 Cutout Dimensions (42”) ________________________________________________________12 Anti-Tip Dimensions (42”) _______________________________________________________13 Cutout Dimensions (48”) _______________________________________________________ 14 Anti-Tip Dimensions (48”) ______________________________________________________ 15... - Page 3 IMPORTANT – Please Read and Follow! • Make sure that incoming voltage is the Your safety and the safety of others is same as unit rating. An electric rating very important. plate specifying voltage, frequency, wattage, amperage, and phase is attached We have provided many important safety to the product.
- Page 4 • The required use of a GFI is normally related to the location of a receptacle with respect to any signifi cant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
- Page 5 Tipping Radius - Door Swing 42” (106.7 cm) 42" Door Swing 9-1/16” 11-3/8” (23.0 cm) (28.9 cm) 6-5/16” 7-7/8” (16.0 cm) (20.0 cm) 15-1/8” 19-3/16” 90° 90° (38.4 cm) (48.7 cm) 110° 110° 16-1/3” (41.5 cm) 120° 20-11/16” 120° 17 1/16” (52.5 cm) (43.3 cm) 21-11/16”...
- Page 6 Tipping Radius - Door Swing 48" Side Tip 131 1/8" (330.1 cm) 48" (121.9 cm) 82 3/4" (210.1 cm) 95 7/8" (243.5 cm) Back Tip 85 1/2" (217.2 cm) 86 1/8" (218.8 cm) 82 3/4" (210.1 cm) 24" (61.0 cm)
- Page 7 Headline Dimensions (Side-By-Side) 42” Side-By Side 3 – 1 9 / 3 2 ” ( 9 . 1 c m 48” Side-By Side 3 – 1 9 / 3 2 ” ( 9 . 1 c m 8 ” – 7 / ( 6 0 8 ”...
- Page 8 Headline Specifi cations (Side-By-Side) 42” Side-By-Side Description VCSB/CVCSB Overall width 42” (106.7 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth from rear To front edge of side trim: 23-3/4 (60.3 cm) To front of top grille: 26-1/4” (66.7cm) To front of handle endcap: 29-3/16”...
-
Page 9: Fl Ush Mount Trim)
Dimensions Headline (Flush Mount Trim and Custom Door Overlay) 42” Side-By Side with Flush Mount Trim 3 – 1 9 / 3 2 ” 48” Side-By Side ( 9 . 1 c m with Flush Mount Trim 3 – 1 9 / 3 2 ”... - Page 10 Headline Specifi cations (Flush Mount Trim and Custom Door Overlay) 42” Side-By-Side Flush Mount Trim and Custom Door Overlay Description VCSB/CVCSB Flush Mount FDSB/CFDSB Overall width 42” (106.7 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth from rear To front edge of side trim: 25-1/2"...
-
Page 11: Cutout Dimensions (42")
Headline Cutout Dimensions 42” Side-By-Side Electric Outlet Location 6 ” ( 1 5 . 2 c m ) 9 ” ( 2 2 . 9 c m ) 9 ” ( 2 2 . 9 c m ) 8 2 – 7 / 8 ”... -
Page 12: Anti-Tip Dimensions (42")
Headline Anti-Tip Dimensions 42” Side-By-Side Anti-Tip Location One 2”x 4” Mounting Board 3” (7.6 cm) x 3-1/2” (8.9 cm) 1 . 5 ” ( 3 . 8 c 7 9 – 3 / 8 ” ( 2 0 1 . 6 c m ) m i n t o b o t t o m... -
Page 13: Cutout Dimensions (48")
Headline Cutout Dimensions 48” Side-By-Side Electric Outlet Location 6 ” ( 1 5 . 2 c m ) 9 ” ( 2 2 . 9 c m ) 9 ” ( 2 2 . 9 c m ) 8 2 – 7 / 8 ”... -
Page 14: Anti-Tip Dimensions (48")
Headline Anti-Tip Dimensions 48” Side-By-Side Anti-Tip Location One 2”x 4” Mounting Board 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) ” 1 - 1 / 2 ( 3 . 8 c 7 9 – 3 / 8 ” ( 2 0 1 . -
Page 15: Cabinet Information
Headline Cabinet Information For installation in 24" (61.0 cm) deep cabinets, the door face protrudes 2-3/4” (7.0 cm) from the cabinet face. The handle protrudes an additional 2-15/16” (7.5 cm) into the room. Standard Mount Installation 1/4” (0.6 cm) 42” (106.7 cm) Finished 48”... -
Page 16: Cabinet Information (With Fl Ush Mount Trim)
Cabinet Information ( with Flush Mount Trim) Flush Mount Installation with Standard Cabinets 1/8” Offset in Finished Wall (0.3 cm) Finished 1-5/8” Wall (4.1 cm) 23-7/8” 24” 26-3/8” (60.6 cm) (61.0 cm) (67.0 cm) 24-5/8” 24-3/4” (62.5 cm) (62.9 cm) 26-1/4”... -
Page 17: Custom Side Panel Dimensions
Headline Custom Side Panel Dimensions 3/16” 3/4” (0.5 cm) (1.9 cm) Back filler End panel panel 6 ” 8 ” - 5 / ( 1 5 ( 6 2 5/32” (0.4 cm) 8 ” - 5 / ( 6 2 ( 2 1 - 7 / 0 . -
Page 18: Custom Side Panel Dimensions (With Fl Ush Mount Trim)
Headline Custom Side Panel Dimensions ( with Flush Mount Trim) Z-Bracket 1” 3/4” (2.5 cm) 1/4” (1.9 cm) (0.6 cm) End panel 8 ” - 7 / ( 6 0 8 ” - 7 / ( 6 0 ( 2 1 - 7 / 0 . -
Page 19: Custom Door Panel Dimensions
Headline Custom Door Panel Dimensions Maximum Panel WT 42" 48" Freezer 30lbs (13.6 kg) 30lbs (13.6 kg) Refrigerator 38lbs (17.2 kg) 48lbs (21.8 kg) 42” Side-By-Side ” 3 / 4 - 3 / ( 1 . 9 ( 4 6 ”... -
Page 20: Custom Door Panel Installation
Headline Custom Door Panel Installation Remove handle side cabinet screws and trim Remove all screws from handle side door trim. with a Phillips screwdriver. Remove two screws from top and bottom door trim. Remove handle side door trim. 2-1/16” 2-1/16” 1-11/16”... - Page 21 Headline Custom Door Panel Installation Slide custom wood panel to the hinge side, ensuring Reinstall handle side door trim “Z” bracket engages the door bracket. and door trim screws. Reinstall cabinet trim and screws.
-
Page 22: General Information
48” Custom Panels General Information Area Requirements A 115 volt, 60-Hz, 15 amp, fused, electrical Verify the following: supply is required. It is required that a separate • Unit can fi t into residence and can be circuit serving only this appliance be provided. moved around corners and through This appliance is equipped with a power supply doorways. - Page 23 Water Supply Requirements behind the unit. Use only 1/4” (6 mm) copper tubing for water • The installation of Viking Range units with a line. DO NOT install copper tubing reverse osmosis system is acceptable as in area where temperatures drop below 35º...
- Page 24 General Information Area Requirements Tip Over Hazard • Most of the unit’s weight is at the top. Appliance is top heavy and tips easily when not Extra care is needed when moving the unit completely installed. Keep doors closed until to prevent tipping.
-
Page 25: Flush Mount Side Trim Installation
Flush Mount Side Trim Installation (Sold Separately) Note: If the unit is to be installed fl ush with the Step 3 - Align the top of the fl ush mount cabinets, the fl ush mount side trim must be side trim with the top of the unit's machine installed fi rst. -
Page 26: Installation
Installation Hinge Adjustment Front of unit Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Retighten four hinge screws. Anti-Tip Installation Wall 2 x 4 Refrigerator Replace unit top. Replace four side screws. Attach one 2 x 4 to wall stud (refer to dimensions page for exact location). - Page 27 Installation Place unit within 3” (7.6 cm) of being fl ush with cabinets. Carefully move unit until semi fl ush with cabinet (depending Note: To avoid cabinet damage, place cardboard on unit). between cabinets and unit. When moving unit, DO NOT crimp, kink or crush water supply line. Pull supply tubing forward under unit.
-
Page 28: Kickplate Installation
Installation Screw Wall 2 x 4 Refrigerator Lift unit off rollers to desired height and level unit using a Insert mounting screws into 2x4 attached to wall stud 5/16” head wrench. NOTE: DO NOT use an electric device. Overtightening can cause damage. Make sure evaporator pan is in correct location. -
Page 29: Door Stop Adjustment
Door Stop Adjustment 90˚ 110˚ 120˚ Open refrigerator door so door stop and shoulder Remove shoulder screw and place in 90º or screw are accessible. Note: Shoulder screw should be 120º position. in 110º door opening position. -
Page 30: Final Installation
Final Installation Replace top air grille. Using an 8” (20.3 cm) magnetic nut driver, replace the two 1/4” (0.6 cm) screws. Replace the center grille louver. Open door. The display should fl ash. Press “ACTIVATE CONTROLS” pad and close door. Note: There is a 6 minute delay before the unit starts. -
Page 31: Performance Checklist
Performance Checklist —Verify cabinet size. — Verify electrical supply and water supply (if applicable). — Install anti-tip device(s) and verify unit is secure. — Position unit in cutout, level at desired height and secure unit. —Plug-in unit and verify operation. —Connect water supply (if applicable). -
Page 32: Control Panels
Verify Operations Control Panel Side-by-Side FREEZER REFRIGERATOR MAX FRZ MAX REF DOOR OPEN ACTIVATE FAST ALARM DISPLAY HIGHER LOWER CONTROLS TEMP TEMP COOL FAST COOL POWER SAB SHOW HIGH TEMP Press “ACTIVATE CONTROLS” pad. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A. -
Page 33: Service & Registration
• Name of dealer from whom purchased Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to:... - Page 36 Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit our web site at vikingrange.com F21445H EN (101519)
Need help?
Do you have a question about the 5 Series and is the answer not in the manual?
Questions and answers