Page 1
THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANUAL(S). Model Order No. Remarks DJM-750MK2 QRT1012 SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST Pioneer DJ Corporation 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 Japan 2017 Pioneer DJ Corporation...
Page 2
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. CAUTION Since the fuse may be in the neutral of the mains supply, disconnect the mains to de-energize the phase conductors. DJM-750MK2...
8.4 METHOD OF DVS CONNECTION CONFIRMATION....................55 8.5 ITEMS FOR WHICH USER SETTING ARE AVAILABLE ..................... 57 9. EXPLODED VIEWS AND PARTS LIST..........................58 9.1 PACKING SECTION ..............................58 9.2 EXTERIOR SECTION ..............................60 9.3 CHASSIS SECTION ..............................62 9.4 CONTROL PANEL SECTION ............................64 DJM-750MK2...
Page 4
11.2 PNLA ASSY................................39 11.3 AINB ASSY................................. 41 11.4 USBA, MICB, HPJK, HPJM, OLED and MTRM ASSYS..................... 43 11.5 CHFD, BFXB, PWSB, HPVR and CRFD ASSYS ....................... 45 11.6 SW POWER SUPPLY..............................47 12. PCB PARTS LIST ................................48 DJM-750MK2...
C4638 and C4639 in the MAIN ASSY are locked with bond to prevent solder cracks caused by fall or vibration. When any of them is replaced for repair, it must be locked with bond after the replacement. Silicon Bond: GYA 1011 DJM-750MK2...
Page 6
• Resister is all 10kΩ(3W) following method. • Both of LED is LTL17KRH5D • Step1: After the power is turned off,wait 2 minutes. • Step2: Connect the Register Jig and leave the unit as it is, for 10 seconds. DJM-750MK2...
MID .............. –26 dB to +6 dB (1 kHz) LOW ............–26 dB to +6 dB (20 Hz) Microphone equalizer characteristic HI ............. –12 dB to +12 dB (10 kHz) LOW ............–12 dB to +12 dB (100 Hz) DJM-750MK2...
NUMBER ”. License-key card for Service GGP1522 For activation of rekordbox dj GGP1523 For activation of rekordbox DVS Lubricants List Name Lubricants No. Remarks Sillcon Bond GYA1011 Used to do bond locking of C4638 and C4639 in the MAIN ASSY. DJM-750MK2...
Page 15
V+12A_CONT [HIGH] V+12A_CONT V+15D_OLED_CONT [HIGH] V+15D_OLED_CONT [V+15A] ON [V+15OLED] ON [V+7R5HP] ON OLED_xRST [HIGH] OLED_RST VR, KDY Reading Reset canceled SHB_RST [HIGH] 1stBOOT Initialization Start (Normal mode) B-PNL_INT [HIGH] Handshake request Handshake response & Key notice Continued on next page DJM-750MK2...
Page 16
Handshake response (7777) Initialization Finish (Normal mode) Starting Normal mode MUTE cancel at 6 seconds after boot complete MUTE OFF command CPU_MUTE OFF [LOW] [CPU_MUTE] OFF 1 second after mute cancel USB A start command V5USB_EN[HIGH] HSSW ON DJM-750MK2...
Page 17
: CENTER MASTER LEVEL : CENTER CROSS FADER CURVE : CENTER BOOTH MONITOR : CENTER SEND/RETURN : 1/4" JACK PHONES VOLUME : CENTER RETURN TYPE : INSERT HP MONO/STEREO : STEREO SEND/RETURN LEVEL : CENTER HP MIXING : CENTER DJM-750MK2...
IC7002. IC7002 1pin Check condition of the solder/replace parts. PANEL_UCOM PNLA ASSY If it does not improve in the above. There is a possibility of failure of the PANEL_UCOM failure (IC7001). Check condition of the solder/replace parts. DJM-750MK2...
IC2001 193pin communication failure USBB_UCOM to MAIN ASSY - USBB_UCOM(IC2001) to DSP(IC3001) HPI DSP communication communication line may have abnormality. (HPI) failure - Check condition of the solder/replace parts. - Still if symptoms do not improve, replace the PC board. DJM-750MK2...
Check the audio signals (other than Replace wires. CN1004 31pin sticking to LOW or HIGH) via relevant - In the case that audio signal exists signal route. =>There is a possibility of failure of the DSP(IC3001). waveform A13 Replace MAIN ASSY. DJM-750MK2...
. via relevant signal route. Check condition of the solder/replace parts. - In the case that audio signal exists. =>There is a possibility of failure of JACK and peripheral circuit . waveform M49 Check condition of the solder/replace parts. DJM-750MK2...
PC,LINE,PHONO - Confirm that select switch is set to PC. Set correctly. Instructions select switch - Install the latest driver. - Confirm that DJM-750MK2 utility of PC CH level meter is set correctly. Power supply MAIN ASSY [Power supply] In the case of abnormality...
- [CROSS FADER signal] [7-1] same as In the case that signal is not outputted, wire may have disconnection. Replace parts. -If it does not improve in the above, resistances or PANEL_UCOM(IC7001) may have solder fault. Repair or replace parts. DJM-750MK2...
Parts failure MAIN ASSY [D±USB] [D±USB] IC2501 93/94pin Confirm that wave form is generated In the case of abnormality in the condition SEND/RETURN is ON. =>There is a possibility of failure of the MAIN ASSY . Replace MAIN ASSY. DJM-750MK2...
While the power supply is turned OFF, check the monitored voltage does not short out with GND. While monitoring each monitored voltage, turn ON the power supply in this mode and check no error is generated. * A single power ON should be within 10 seconds. DJM-750MK2...
"Start" -> "Control panel" -> "System" -> "Device Manager" Added and displayed device - Universal Serial Bus controllers USB Composite Device - Sound, video, and game controllers DJM-750MK2 DJM-750MK2 Opening the device manager on the PC makes the connection work easier to check. [2. USB A connector] Confirm that USB communication is normal between the USB A terminals of this unit and the external devices.
Please power supply is turned ON while pressing (1) to (3) button at the same time. Holding down (1) to (3) button until display becomes the version confirmation mode . Test mode Exit Method Please power supply is turned OFF by press the POWER button. DJM-750MK2...
Page 28
Level meter LED confirmation mode [TAP] Test Mode 10 Volume A/D value confirmation mode [TAP] Test Mode 11 Fader A/D value confirmation mode [TAP] Test Mode 12 Device confirmation mode [TAP] Test Mode 13 OLED Iuminance confirmation mode [TAP] DJM-750MK2...
Page 29
Software name Displaying SYSTEM SYSTEM SH-B SH-A SH-BOOT BOOT PANEL PANEL PANEL-BOOT PANEL-B DSP Program DSP P DSP Data DSP D [BEAT DOWN] [BEAT UP] [BEAT DOWN] [BEAT UP] Firmware version of the SYSTEM is indicating that is 1.00. DJM-750MK2...
Page 30
If three time retries fail to acquire A/D values, acquisition error is determined. • A/D values that are set in this mode become effective immediately after saving. • Should an error occur, setting must be started again without changing the mode. DJM-750MK2...
Page 31
Outline LED and display will be all lighting. Display mode title ALL SET * This is displayed for about 1 second at the start of mode. Operation [TAP] : Mode change (to next mode) Lighting points during all lighting DJM-750MK2...
Page 32
UTILITY WAKE UP LED UTILITY FX FREQUENCY LOW FX FREQUENCY LOW LED FREQ L FX FREQUENCY MID FX FREQUENCY MID LED FREQ M FX FREQUENCY HI FX FREQUENCY HI LED FREQ H EFFECT ON/OFF EFFECT ON/OFF LED EFX ON DJM-750MK2...
Page 33
Mater Level Meter Rch LED * SW left is assumed 1 and right is assumed 11. TIME knob Operation range Initial value : 10 12dB Maximum value : 100 15dB Minimum value : -100 Minimum value Initial value Maximum value Counterclockwise Clockwise DJM-750MK2...
Page 34
Correlation diagram of the operation switch and lighting LED DJM-750MK2...
Page 35
"HI" : Full Illuminate CH4 COLOR CH4 Level Meter LED "LOW" : Lights off "HI" : Full Illuminate SND/RTN LEVEL Master Level Meter Lch LED "MIN" : Lights off "MAX" : Full Illuminate * Refer to the next page for grouping details DJM-750MK2...
Page 36
Grouping details : Group 1 : Group 4 : Group 2 : Group 5 : Group 3 DJM-750MK2...
Page 37
Operation button Lighting meter CH1 CUE CH1 Level Meter CH2 CUE CH2 Level Meter CH3 CUE CH3 Level Meter CH4 CUE CH4 Level Meter MASTER CUE Master Level Meter Lch LED FREQUENCY LOW Master Level Meter Rch LED/CLIP LED DJM-750MK2...
Page 38
NG display LED PNL_MODE CH1 Level Meter -24dB LED A-PNL_MOSI CH1 Level Meter -18dB LED A-PNL_MISO CH1 Level Meter -12dB LED A-PNL_CLK CH1 Level Meter -9dB LED A-PNL_CTRL CH1 Level Meter -6dB LED A-PNL_INT CH1 Level Meter -3dB LED DJM-750MK2...
IC3001 MAIN ASSY DSP SDRAM RAM for DSP (Work) A3V28S40JTP-60 IC3003 MAIN ASSY PANEL UCOM Main, LED, OLED, KEY and VR control DYW**** *1 IC7001 PNLA ASSY *1 : [****] of DYW**** changes each time the firmware is updated. DJM-750MK2...
Slide the Panel (DNK6689) to the right, and then remove it toward the near side. Remove the two screws (BBZ30P060FTC) and two Washers (WB30FTC). Note on assembling ∗2: Refer to the “[3-3] Attach the Control Panel Section to the Chassis”. DJM-750MK2...
Page 41
Saddle (Pls). Shielded CONN-CABLE Remove the four screws (BBZ30P060FTC) and then remove the Shield Plate (DNF2023). Shield Plate Note on assembling ∗6: Attach the screws in the order as shown by orange numbers. Locking Mini Clamp Edge Saddle (Pls) Diagnosis DJM-750MK2...
Page 42
(DEC2920). Remove the six screws. (PPZ30P080FTB) Remove the five screws. (BPZ30P080FTB) Remove the Screw (M3x5). (DBA1340) Note: When MAIN ASSY is not removed, • Rear view screws, nuts and washers of blue numbers need not to be removed. DJM-750MK2...
Page 43
(Refer to the “[3-2] Shield Plate (DNF2023), Stay (DNF2024)” ) Shield Plate (DNF2022) Remove the four screws (BBZ30P060FTC), and then remove the Shield Plate (DNF2022). Note on assembling Front ∗12: Attach the screws in the order as shown by blue numbers. DJM-750MK2...
Page 44
∗19: Attach the screws in the order as shown by blue numbers. PWSB ASSY Release the tip of the PCB Holder (PNW1706), and then remove the PWSB ASSY while drawing the Power Knob from the Power Knob Guard. Power Knob Remove the Power Knob. DJM-750MK2...
Page 45
Remove the four Knobs. Remove the five Slider Knobs. Note: Each Slider Knob has a lock mechanism. (Refer to the next page) Remove the seven screws. (DBA1451) Note on assembling ∗23: Attach the screws in the order as shown by blue numbers. DJM-750MK2...
Page 46
Control Panel is damaged, replace it with new ones. CN7601 ∗27 Fader Packing Control Panel (Back surface) CHFD ASSY FFC (DDD1808) PNLA ASSY Disconnect the connector, and remove the FFC (DDD1808) by drawing it out from the slit of the CHFD ASSY. DJM-750MK2...
Page 47
Remove the Stay (DNF2026) from the BFXB CN7701 ASSY. Remove the Button (DAC3141) and SW FFC (DDD1809) Packing (Ef). SW Packing (Ef) Button FFC (DDD1807) Disconnect the connector. Remove the Cap /MIC from the HPVR ASSY. HPVR ASSY CN8101 Cap /MIC DJM-750MK2...
Page 48
Remove the four Flange Nut M9s. Holder (DNK6692) Note on assembling PNLA ASSY ∗31: Make sure not to invert CN7004 OLED ASSY the mounting locations for the Button (DAC3249 Holder /LED and DAC3251). CN7008 CN7006 CN7012 CN7003 ∗31 Button (DAC3249) CN7001 Button (DAC3251) DJM-750MK2...
Page 49
7 6 5 ASSY, MICB ASSY must be attached in the Front order as shown by orange numbers. AINB ASSY Stay (DNF2024) Note: Before the attachment of the orange screws , attach the screws on the Rear Panel side. DJM-750MK2...
Page 50
Barrier (DEC3745) Bend at the 2 mm distance into the slit of Barrier from the reinforcement board. (DEC3735). FFC (DDD1806) Connect the FFC to the MAIN ASSY’s MAIN ASSY Connector with the ends which have longer reinforcement board. CN1003 DJM-750MK2...
Page 51
CN6601 CN8901 CN4601 (blue) Connector ASSY MAIN ASSY CN4602 Holder (PF03PP-B12) Shielded CONN-CABLE Shielded CONN-CABLE Front Front Edge Saddle (Pls) [3-5] Edge Saddle (Pls) It has a direction with front and back sides. Shield Plate hook facing upward (DNF2023) DJM-750MK2...
Page 52
C4638 and C4639 in the MAIN ASSY are locked with bond to prevent solder cracks caused by fall or vibration. When any of them is replaced for repair, it must be locked with bond after the replacement. Silicon Bond Silicon Bond used: GYA1011 DJM-750MK2...
(Refer to 6.1 TEST MODE [2. Cross fader setting mode "CFDR SET"]) • Cross Fader ASSY • Acquire and save the maximum and minimum A/D value of [Cross Fader]. (Refer to 6.1 TEST MODE [2. Cross fader setting mode "CFDR SET"]) DJM-750MK2...
OFF and pull out the USB memory for update. Then, update is finished. If update is not started, retry from the firmware down load. If you still cannot update, it is considered the cause of USB memory. Please try another USB memory. DJM-750MK2...
PC. Connect the USB B terminal of unit and PC using the 750MK2 USB cable. Keep pressing the keys [NOISE] + [FILTER] + [CH1 CUE] and power supply is turned ON of DJM-750MK2. DJM-750MK2...
Please refer to following details setup in the setting items. Setting items Setup material items Enables DVS function Connects CDJs/DECK1 to MIXER CH1 No setting because it is not connecting using a turn table Settings, play rekordbox dvs specific control signal at the CDJ. DJM-750MK2...
Page 57
[Environment set] of the rekordbox (PERFORMANCE mode) -> Conduct the following settings using [DVS] . [1] DVS function enable/disable [2] Rooting set [3] Control signal set 4.1 DVS function enable/disable DVS function enable Checkmark the [DVS function enable] to switch each DECK to DVS mode. DJM-750MK2...
ADVANCED NORMAL –24 dB –18 dB –12 dB –6 dB MIDI OLED BRIGHTNESS BUTTON TYPE 9 10 11 12 13 14 15 16 TOGGLE TRIGGER PC UTILITY AUTO STANDBY Factory Reset Do not perform it before writing in user setting. DJM-750MK2...
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION DJM-750MK2...
Page 60
LSYXJ, UXJCB and XJCN are constructed the same except for the following: Mark Symbol and Description LSYXJ UXJCB XJCN Power Cord ADG1244 DDG1108 DDG1114 Leaflet DRH1431 DRH1431 DRH1432 Operating Instructions (Quick Start Guide) DRH1433 DRH1434 DRH1436 Warranty DRY1270 Not used Not used Packing Case DHG3572 DHG3573 DHG3575 DJM-750MK2...
9.2 EXTERIOR SECTION ∗ Accessory of VR ∗ ∗ Refer to “9.4 CONTROL PANEL SECTION” ∗ ∗ ∗ ∗ PNLA ASSY CN7008 PNLA ASSY CN7006 MAIN ASSY CN2502 Refer to “9.3 CHASSIS SECTION” DJM-750MK2...
Page 62
NSP 34 Label See contrast table (2) (2) CONTRAST TABLE LSYXJ, UXJCB and XJCN are constructed the same except for the following: Mark Symbol and Description LSYXJ UXJCB XJCN Name Label DAL1349 DAL1349 DAL1351 Label Not used DRW1975 Not used DJM-750MK2...
When any of them is replaced for repair, it must be locked with bond after the replacement. Silicon Bond used: GYA1011 C4638 C4639 USBA ASSY CN1601 Silicon Bond ∗ Glue Silicon Bond : GYA1011 Front DJM-750MK2...
Page 68
CONNECT BLOCK 1/11 MAIN ASSY (DWX3997) The check point for service. (Legend silk indication on the PCB.) Regulator 12V=>5.0V(EVER) POWER DOWN DETECTION CIRCUIT NOTES is STBY V+12E RS1/16S****J V+12SW V+12SW_OPA V+12A V+12E V+5E RS1/10S****J V+12SW V+12E ACOFF_DET RS1/16S****D CN1001 RS1/10S****D DKN1666-A RS1/16S****F V+12SW_OPA...
Page 69
2/11 MAIN ASSY (DWX3997) POWER(DIGITAL) BLOCK The check point for service. (Legend silk indication on the PCB.) VOLTAGE DETECTION CIRCUIT V+12SW DC/DC Converter 12V=>3.3V(D) V+3R3D V+3R3D V+3R3OLED V+3R3D V3R3D_CONT L1204 10:7G;1D;14:5G 1/11, 3/11 CTH1561-A V+1R25D V+5A V+3R3D V+5A V+5A V+3R3D V+15A V+5D FAULT_DET...
Page 70
3/11 POWER(AUDIO) BLOCK MAIN ASSY (DWX3997) The check point for service. (Legend silk indication on the PCB.) DC/DC Converter 12V=> 7.5V(HP) V+12SW_OPA V+2R5REF_HP for DAC,ADC POWER IC1403 R1425 BD9851EFV Regulator 9V=>5V(A) ADC/DAC(AVDD) Regulator 12V=>9V(A) SEL1 R1409 R1410 R1423 C1433 C1443 R1432 R1434 D1416...
Page 71
USBB UCOM 4/11 MAIN ASSY (DWX3997) V+3R3D The check point for service. (Legend silk indication on the PCB.) V+3R3D CN2001 IC2005 TC7SZU04FUS2 IC2007 V+3R3D V+3R3D 5/11 UB_JTAG_ASEMD GNDD IN_A SH_ASEMD R2129 USBA_CLK(48MHz) SH_TCK OUT_Y OUTY 25:12D UB_PNL_SPI SH_TRST 10:11E GNDD R2122 TC7SZ08FUS2 R2130...
Page 72
5/11 MAIN ASSY (DWX3997) USBA UCOM V+3R3D CN2501 The check point for service. V+3R3D (Legend silk indication on the PCB.) UA_PNL_SPI V+3R3D 10:11E U A _ J T A G _ A S E M D SH_ASEMD 1/11 SH_TCK IC Distinction SH_TRST (LOW:UA HI:UB) JTAG...
Page 73
DSP (1/2) 6/11 MAIN ASSY (DWX3997) The check point for service. (Legend silk indication on the PCB.) IC3001 SDRAM 128M V+3R3D D810K013DZKB400 V+3R3D B 1 6 D V D D 1 V s s 1 IC3001 D V D D 2 V s s 2 D810K013DZKB400 D V D D 3...
Page 74
7/11 MAIN ASSY (DWX3997) DSP (2/2) V+3R3D_CLK V+3R3D_CLK The check point for service. C 3 5 1 6 C 3 5 1 2 (Legend silk indication on the PCB.) C 3 5 1 8 C 3 5 1 4 V+3R3D_CLK 0 .
Page 75
8/11 MAIN ASSY (DWX3997) Multi-DAC Chip Address:01 The check point for service. (Legend silk indication on the PCB.) V+5A_REF V+3R3A R 4 0 0 5 1.8V GNDA x R S T _ 4 4 5 8 35:12G BOOTH_R- 44:1G 10/11 M C L K _ 4 4 5 8 BOOTH_R+ 35:7C...
Page 76
9/11 MAIN ASSY (DWX3997) MASTER1/MASTER2 V+15A_O C 4 2 1 9 C 4 2 1 3 DNF1789-A CANON SHIELD MASTER1 L V+15A_O 0 . 1 u / 2 5 R 4 2 6 1 GNDA_F GNDA JA4201 CANON SHIELD 1 0 k C 4 2 3 5 DKB1093-A 0 .
Page 77
10/11 BOOTH MAIN ASSY (DWX3997) V+15A_O C 4 4 1 3 V+15A_O V+15A_O 0 . 1 u / 2 5 BOOTH Lch GNDA C 4 4 2 1 C 4 4 3 3 C 4 4 3 4 0 . 1 u / 2 5 1 0 0 u / 1 6 1 0 0 u / 1 6 JA4401...
Page 78
11/11 MAIN ASSY (DWX3997) SEND BLOCK DNF1875-A PHONE SHIELD V+15A_O C 4 6 1 5 SEND_L (SEN OUT) R 4 6 0 1 R 4 6 1 7 0 . 1 u / 2 5 S E N D _ L - JA4601 40:8D 6 .
Page 79
PNLA ASSY (DWX3996) CN8101 CN7601 ANA_P_CON discharge V K N 1 2 3 7 - A CN7701 V K N 1 2 4 8 - A High V+15OLED V+15OLED1 V+3R3D_REF_L Q 7 0 6 9 R 7 2 4 6 L S A R 5 2 3 U B V K N 1 2 5 0 - A V+3R3D_REF_L...
Page 81
PNLA ASSY (DWX3996) 1/3, 2/3 IN3 SELECT IN1 SELECT VR_SEL_C VR_SEL_B VR_SEL_A AD_0 VOLUME SELECT V+3R3D_REF_L C 7 0 6 7 0 . 1 u / 1 6 CH1 TRIM CH2 TRIM CH4 TRIM V C C CH3 TRIM MAS_LEVEL K E Y _ S E G 0 _ P N L V+3R3D_REF_L V+3R3D_REF_L...
Page 82
BOARD IF AINB ASSY (DWX3999) V+3R3D_CLK IC5002 TC7SZ08FUS2 24.576MHz MCLK For SW OPAMP R 5 0 2 8 I N B 60:3D R 5 0 1 7 M C L K _ C H 1 - 4 V-15A_IN V+15A_IN I N A V-15A V+15A GNDD...
Page 83
CH1_INPUT AINB ASSY (DWX3999) V+15A_IN C 5 1 2 5 V+15A_IN A C E 7 1 2 8 - A C 5 1 3 8 0.33u/50 0 . 1 u / 2 5 C 5 1 1 9 P1OUT_L GNDA_PH1 I C 5 1 0 4 GNDA_PH1 I C 5 1 0 1...
Page 84
CH2_INPUT AINB ASSY (DWX3999) V+15A_IN C 5 3 2 5 V+15A_IN A C E 7 1 2 8 - A C 5 3 3 8 0.33u/50 0 . 1 u / 2 5 C 5 3 1 9 P2OUT_L GNDA_PH2 GNDA_PH2 I C 5 3 0 4 I C 5 3 0 1...
Page 85
CH3_INPUT V+15A_IN AINB ASSY (DWX3999) C 5 5 2 5 V+15A_IN A C E 7 1 2 8 - A C 5 5 3 8 0.33u/50 0 . 1 u / 2 5 PHONO C 5 5 1 9 GNDA_PH3 P3OUT_L GNDA_PH3 I C 5 5 0 4...
Page 86
CH4_INPUT V+15A_IN AINB ASSY (DWX3999) C 5 7 2 5 V+15A_IN A C E 7 1 2 8 - A C 5 7 3 8 0.33u/50 0 . 1 u / 2 5 C 5 7 1 9 PHONO GNDA_PH4 P4OUT_L I C 5 7 0 4 GNDA_PH4...
Page 87
RETURN/MIC ADC AINB ASSY (DWX3999) V+15A_IN C 5 9 0 8 C 5 9 0 5 4 7 u / 2 5 4 7 u / 2 5 GNDA_RTN GNDA_RTN V-15A_IN V+15A_IN V+15A_IN V+5A RETURN C 5 9 2 7 C 5 9 0 6 RTN_L 0 .
Page 88
CH1- CH4 ADC AINB ASSY (DWX3999) Chip Address:00 (IN) C H 3 _ L + 55:9E (IN) C H 3 _ L - 55:9E C H 2 _ R + 53:9H C H 2 _ R - V+5A 53:9G R 6 0 1 1 R 6 0 1 9 (IN) C H 2 _ L -...
Page 89
USBA ASSY (DWX3998) MTRM ASSY (DWX4005) USBA MIC TRIM CN7901 MIC LEVEL CN1601 A K M 1 2 8 1 - A MIC_TRIM_IN USB CONNECTOR (MIC I) GNDD_USBC (A-TYPE) GNDD_USBC Rating (MIC I) V+5R2D_VBUS 30V/ 2.5A V+5R2D_VBUS C 1 6 0 2 10u/10 5/11 V+5R2D_VBUS...
Page 90
HPJK HPJK ASSY (DWX4001) HPJM HPJM ASSY (DWX4002) C 6 7 0 1 C 6 6 0 1 0.01u/50 A C E 7 1 1 3 - A 0.01u/50 A C E 7 1 1 3 - A C 6 7 0 2 C 6 6 0 2 0.01u/50 A C E 7 1 1 3 - A...
Page 91
OLED ASSY (DWX4010) CHFD ASSY (DWX4003) OLED CHFD CH1 FADER V+3R3D_REF_L CH1_FADER V R 7 6 0 4 D C V 1 0 2 0 - A GNDD_REF_L2 V+3R3D_REF_L CN7601 CH1_A/B CH3_A/B CH_CURVE1/3 V K N 1 2 4 8 - A CH2 FADER S7601 S7616...
Page 93
SW POWER SUPPLY SW POWER SUPPLY SW POWER SUPPLY (DWR1548) AC POWER CORD 1/11 CN1001 CRFD CRFD ASSY (DWX3258) IC4001 EM-3242 V+3R3REF CN4001 A K M 1 2 7 4 - A T S T B T E S T A V S S V D D V+3R3REF...
Page 94
The indicated voltage values of the oscilloscope in this section are reference values and may vary, depending on the settings of the oscilloscopes and probes. Numbers surrounded by red square indicate denote numbers for the measurement points in the Schematic diagrams and PCB diagrams. DJM-750MK2...
Page 100
11. PCB CONNECTION DIAGRAM SIDE A CN7006 CN7008 SIDE A MAIN ASSY CN1013 CN1002 R4659 M35 M34 CN1005 CN1004 CN5002 CN5001 CN2502 CN1006 (DNP2866-A) CN1601 CN8901...
Page 101
SIDE B SIDE B MAIN ASSY CN2502 CN1006 CN1005 CN1004 C4218 R4248 R4238 R4247 C1065 C1066 R4237 C1465 R4246 IC1407 R4236 D1424 0 1 2 3 0 1 2 3 4 5 6 7 8 9 D1420 D1422 R4245 D1421 C1466 C1468 R4235...
Page 102
SIDE A SIDE A PNLA ASSY S7021 1/4 JACK RTN_IN_SELECT S7003 S7015 S7016 VR7011 S7002 INPUT SELECT INPUT SELECT INPUT SELECT MASTER LEVEL INPUT SELECT S7022 CH1 TRIM CH2 TRIM CH3 TRIM CH4 TRIM VR7001 VR7006 VR7013 VR7020 INSERT RETURN TYPE D7061 D7039 D7050...
Page 103
SIDE B SIDE B PNLA ASSY CN7008 CN7006 CN7012 CN7003 CN7001 (DNP2869-A)
Page 105
SIDE B SIDE B AINB ASSY CN5001 CN5002 (DNP2867-A)
Page 106
SIDE A SIDE A HPJK ASSY OLED ASSY USBA ASSY C6604 CONTACT SIDE HPJK DWX4001 DWX4010- OLED [[ G ]] [[ G ]] JA6601 C6603 B30C5A3/C7 VA6601 A30C5/C7 WHITE MANUAL CN6601 SOLDER 2.USBC_DP etc.GNDF_USBC 3.USBC_DM DWX3998- 6-8.V+5R2D_VBUS USBA CN1601 C1806 CN1802 CN1801 VA6603...
Page 107
SIDE B SIDE B MICB ASSY CN6502 CN6501 MTRM ASSY CN7901 CN7901 (DNP2867-A) MTRM DWX4005- HPJM ASSY J7901 GND_MIC [[ G ]] CN6701 (DNP2868-A) (DNP2867-A) OLED ASSY USBA ASSY HPJK ASSY CN1601 CN1801 CN6601 (DNP2866-A) (DNP2866-A) (DNP2867-A) D E F G H K D E F G H K...
Page 108
SIDE A SIDE A CRFD ASSY CHFD ASSY CRFD ASSY because of only ASSY replacement, PCB CONNECTION DIAGRAM is not mentioned. CN7602 CN7602 PWSB ASSY CRF_CURVE1/3 S7617 J7626 CH4_A/B CH3_A/B CH2_A/B CH1_A/B J7627 S7614 S7613 S7612 S7601 THRU THRU THRU THRU J7609 CH_CURVE1/3...
Page 122
Mark No. Description Part No. SW POWER SUPPLY SW POWER SUPPLY because of only PCB replacement, parts are not serviced. CRFD ASSY CRFD ASSY because of only ASSY replacement, parts are not serviced. DJM-750MK2...
Need help?
Do you have a question about the DJM-750MK2 and is the answer not in the manual?
Questions and answers