Subscribe to Our Youtube Channel
Related Manuals for Matsusada Precision EQ Series
Summary of Contents for Matsusada Precision EQ Series
- Page 1 Instruction Manual EQ SERIES MODEL *186.9.002* Rev. 0.4 B/N 186.9.002 F-RA-001-3R1...
- Page 2 SAFETY This power supply unit generates high voltage and energy. Electric shock may lead to death or serious injury. Be sure to follow the instructions below and handle the unit with caution. 1. BE SURE TO GROUND!! Be sure to ground the power supply unit before use. 2.
- Page 3 Symbols Various symbols are used in this instruction manual and on the product for ensuring safety. What will be caused by ignoring the instructions given with the symbols or by improper handling are classified as shown below. Read carefully and understand the descriptions before proceeding to the main body of this manual.
- Page 4 Caution ！ Do not install the unit upside down or Do not use the unit in a place subject to on a wrong side. high temperature or in an enclosed, Insufficient heat release may cause limited area. deterioration of parts, which may It not only hampers the unit from generate smoke or set fire.
- Page 5 First-aid procedures to be implemented in case of electrical shock RESCUE 1. Free victim from contact with live conductor quickly. Avoid contact with neither live conductor nor victim’s body. 2. Shut off high voltage at once and ground the circuit. If high voltage cannot be turned off quickly, ground the circuit to discharge, or cut high voltage line by an ax with dry wooden handle.
- Page 6 Artificial respiration PLACE VICTIM 2.Clear throat Place victim in face-upward position horizontally. CLEAR THROAT Turn head to one side quickly wipe out any fluid, mucus, or foreign body from mouth and throat with fingers. 3.Open air passage OPEN AIR PASSAGE Tilt head back and extend neck to open air passage.
- Page 7 WARRANTY 1. WARRANTY POLICY Matsusada Precision Inc. ("Matsusada") warrants that the products supplied by it will be free from defects in materials and workmanship for a period of twelve (12) months from the date of original shipment to buyer. This warranty shall not apply to any product which has been repaired, modified...
-
Page 8: Table Of Contents
CONTENTS Ｐａｇｅ Safety ⅰ For Safe Use ⅱ，ⅲ Rescue (First aid) ⅳ Artificial respiration ⅴ WARRANTY ⅵ CONTENTS ⅶ １． Introduction 1－1 Introduction 1－2 Unpacking the power supply 1－3 Environmental Requirements 1－4 Points to be careful about in handling 1－5 Troubleshooting Exterior View Diagram ２．... -
Page 9: 1－2 Unpacking The Power Supply
1 Introduction 1 Introduction 1-1 Introduction Thank you very much for your purchase of our product, HIGH VOLTAGE POWER SUPPLY. We have done our best for the quality control of our products. Please handle this unit properly according to this instruction manual so that you can use the full performance of this unit safely for long. -
Page 10: 1－4 Points To Be Careful About In Handling
1 Introduction 1-4 Points to be careful about in handling ・ For your safety connect the ground terminal of the chassis to EARTH securely ・ Use thicker (5SQ or thicker) and short wire for chassis grounding or load grounding, and ground at one point of the ground. -
Page 11: ２． Exterior View Diagram
2 Exterior view diagram 2 Exterior view diagram ２－１ Front Panel ① OUTPUT ON display (LED) ⑥ （LED light on for enable the output） ① ② OUTPUT ON/OFF Switch ⑦ ② ③ Abnormal LED （LED light on at O.V.P. or either of O.C.P. ） ④... -
Page 12: ３． Instructions For Operation 3－1 Operation
3 Instructions for operation 3 Instructions for operation 3-1 Operation 1) Make sure that the connection is done correctly (Refer to Page 2. [How to GROUND]), and operate it. For your safety connect the ground terminal of power supply to the earth. 2) Connect the enclosed AC input cord to the outlet. -
Page 13: ４． Standard Functions
Standard Functions 4 Standard Functions 4-1 Remote connector (D-sub 25pin) pin assign D-sub connector D-sub connector M2-6 fixing screw M2-6 fixing screw PIN No. SIGNAL FUNCTION Remote Voltage Program In 0～10 V / 0～100 % rated output Output current monitor 0～10 V / 0～100 % rated output Remote switch ON/OFF Short to 11pin＝Output ON、Open ＝OFF... -
Page 14: Remote Switch On/Off
Standard Functions 4 Standard Functions c. Remote Switch ON/OFF The output can be turned on and off with remote switch. ⑤ ⑪ REMOTE SWITCH ACTION Remote switch Short …… Output ON action with switch Switch Open …… Output OFF Remote switch In place of switch, an open collector ※1 with open collector... -
Page 15: Optional Function
5 Optional Function 5 Optional Function 5-1 Optional function Cut off function (LCt) Cut off the output at approximately 105% of rated output current. Turn off the POWER switch and back it on to reset the cut-off status.
Need help?
Do you have a question about the EQ Series and is the answer not in the manual?
Questions and answers