Due to the characteristics and physical principles inside flash memory, memory cards have a finite lifetime dictated by the number of write operations. Therefore, take care of the regular write operations to prevent an early flash damage. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...
Moreover, sometimes it is impossible or even dangerous. For such cases IMAGO has developed the VisionDevice – Industrial DashCam 1 000(VD-IDC). The Industrial DashCam 1 000 is a surveillance and remote monitoring camera for industrial environments in a match box form factor.
Environment: Parameter Value Unit Weight, including cable Operating temperature °C Operating humidity, relative, non-condensing Storage temperature -10 … +70 °C Storage humidity, relative, non-condensing 5 … 95 IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...
The input signals use a Schmitt trigger circuit with the power supply GND as voltage reference. The digital output circuit uses open-emitter configuration. All outputs are internally supplied by the 24V power input. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Figure 2, or on the right side. Indicator bar is always located on the bottom of the page and contains most used information about Industrial DashCam. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Page 13
Page 13 / 31 Figure 2: Welcome page. Navigation panel on the left (marked with dashed blue line); Indicator bar on the bottom (marked with red dashed line). IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
6.3.1 Indicator bar Indicator bar contains several indicators, see Figure 3. There are indicators for the following information: 1. IMAGO Technologies Copyright note 2. Name of the system (can be changed on the Configuration page). 3. “Saving in progress” indicator.
Once the button is clicked all the messages are marked as read and remain in the Event Log, see Figure 5. Figure 5: Left, Event Log button indicating one error. Right, Example of the Event log with an error IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Setting a long exposure time might lead to decrease of the acquisition framerate, therefore please consider opening the aperture or bringing more light into the scene. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Page 17
0 to send out the exposure signal so an external LED can be triggered. When setting the mode to “Both”, internal LEDs as well as the digital output 0 are set up to be used (Internal still S-Mount only). IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
The settings are applied only after pressing the “Use” button, some settings might require restart of the application or even reboot of the whole system. Figure 9: Configuration page and three tabs, the “General” is selected IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Note: The synchronization of the time will only last until the camera is rebooted or shut down the next time. After this, the user is required to synchronize the time manually again. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
“Use” button. The largest possible area of interest can be set by pressing “Maximize” button and confirming the choice with the “Use” button. Figure 11: Area of Interest dialog. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
When none is at the trigger point mixed mode is used. A speech bubble that is indicating the time offset appears when clicking on the slider. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
The Min Events field is set in percentage relative to the triggering area size. Typical range values are: Bias 30 - 150 Min Events 5 – 50% IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...
Page 24
6 Web Based Graphical User Interface (WebGUI) Page 24 / 31 Figure 13: Triggering tab of configuration page IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...
“Select All” check box. Note when downloading multiple files, you still need to click the dialog for each one. Figure 14: Video selection dialog. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
Welcome-page will be shown. Finally, the video can be downloaded on this site by pressing the green download-button. Figure 15: Web-based video player IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
To know if the video is still loading, a green progress bar is displayed at the bottom of the page. Pop-up messages will notify about start and end of loading process. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
1. Version the software and the VIB-library 2. Serial number of the Industrial DashCam 3. Sensor type and resolution 4. Temperature 5. Free space on the SD-card. Figure 17: About page IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...
“Reboot System” button in the menu reboots the operation system as well as the Industrial DashCam soft- ware. This option must be used for when changing the IP-address of the Industrial DashCam. IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com;...
7 Support Page 30 / 31 7 Support Finally, if you have any open questions, the IMAGO support team is happy to assist you in any cases. For direct contact to the support, please use our ticket system: https://imago.freshdesk.com Also, visit our IMAGO Download Portal: https://www.imago-technologies.com/support...
8 History Page 31 / 31 History Revision Date Changes Aug-04-2023 First release Based on IDC manual V 1.3 IMAGO Technologies GmbH Strassheimer Str. 45; 61169 Friedberg; Germany; Tel. +49(0)6031-6842611 info@imago-technologies.com; www.imago-technologies.com...