Page 1
IN230600537V01_DE A71-034V01 Yoga-Trampolin *Bitte überprüfen Sie, ob die Beine des Trampolins fest installiert sind. WICHTIG, FÜR DIE SPÄTERE VERWENDUNG AUFBEWAHREN: SORGFÄLTIG DURCHLESEN VERWENDUNGSANLEITUNG...
Page 2
Katalog Warnung: Dieses Produkt ist nicht für Kinder unter 6 Jahren geeignet. Um Unfälle zu vermeiden, ist stets die Aufsicht eines Erwachsenen erforderlich. Bitte lesen Sie vor der Aufstellung alle Anweisungen sorgfältig durch - Bewahren Sie diese Anleitung zum späteren Nachschlagen auf. Wichtige Hinweise Diagramm zur Produktanalyse Stückliste...
Page 3
Wichtige hinweise 1. Dieses Produkt ist für Kinder ab 7 Jahren empfohlen. Die maximale Belastung beträgt 100 kg. 2. Die Stützen des Trampolins werden bei der Aufstellung gut befestigt. Verge- wissern Sie sich, dass die Stützen während des Vorgangs nicht gewaltsam verformt werden.
Page 4
Wichtige hinweise 13. Lesen und verstehen Sie vor der Verwendung alle Informationen - bewahren Sie sie zum späteren Nachschlagen auf. 14. Vergewissern Sie sich vor der Verwendung, dass das Trampolin korrekt auf- gestellt ist, und befolgen Sie alle Anweisungen in dieser Anleitung. 15.
Page 7
Montageschritte Abb. 1 Abb. 2 Abb. 3 Abb. 4 Abb. 5 Schritt 1: Legen Sie das Trampolin in der zusammengeklappten Position auf den Boden (Abb. 1), ziehen Sie an der linken und rechten Seite, so dass das Trampolin einen Halbkreis bildet. Vergewissern Sie sich, dass sich der Klappbügel nahe am Boden befindet (Abb.
Page 8
Montageschritte Abb. 6 Abb. 7 Abb. 8 Schritt 5: Ziehen Sie den Silent-Foot-Stecker oder den Saugnapf heraus, montieren Sie die Stützen-Verbindungsstange jeweils auf die beiden Stützen (Abb. 6) und sichern Sie sie anhand den Dreiecksschrauben. Halten Sie beim Verschrauben das Fußrohr fest und nicht die Stützstange.
Page 9
Montageschritte Abb. 9 Abb. 10 Schritt 8: Schieben Sie die Sensorhalterung über das Fußende des Bettes. Wenn der Sensor das Trampolin berührt (Abb 9), sollte er horizontal mit dem Sprungtuch in Kontakt sein. Ziehen Sie die dreieckigen Schrauben an der Sensorhalterung fest (Abb 9). Setzen Sie den Computer in die Sensorhalterung ein.
Page 10
IN230600537V01_DE A71-034V01 Yoga Trampoline *Please check the legs of the trampoline are firmly installed. IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY UESR’S MANUAL -10-...
Page 11
Catalog Warning: This product is not suitable for children under 6 years old. To prevent accidents, please use it under the supervision of adults at all times! Please read the manual carefully before installing the product and keep the manual properly.
Page 12
Important notes 1. This product is recommended for ages over 7 years. The maximum load is 100kg. 2. The bed legs of the trampoline are firmly installed during assembly. Ensure the bed legs are not deformed due to force during the assembly process. 3.
Page 13
Important notes 13. Read and understand all information before use – keep for future reference. 14. Before use, ensure the trampoline is assembled correctly, following all instructions in this manual. 15. Only to be used by one person at a time. 16.
Page 14
Product analysis diagram Armrest corss Right armrest bracket Trampoline Pentagonal screw Bracket link Triangle screw Safety bolt Leg tube -14-...
Page 15
Part list 1.Trampoline x1 2.Protective case x1 3.Armrest bracket x2 4.Bracket link x2 5.Armrest corss x1 6.Leg tube x6 Mute foot plug x6 Pentagonal screw x2 Long pentagonal screw x2 Safety bolt x2 -15-...
Page 16
Installation steps Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Step 1: Place the trampoline on the floor in its folded position (Fig. 1), pull the left and right sides, so the trampoline is in a semi circle. Ensure the folding clamp stick is close to the ground (Fig.
Page 17
Installation steps Fig. 6 Fig. 7 Fig. 8 Step 5: Pull out the silent foot plug or suction cup, put the support connecting rod on the two feet respectively (Fig. 6), then lock with triangle screws. When screwing the foot tube, hold it and not the support rod. Step 6: After connecting the handrail bracket with the cross bar, tighten with triangle screws (Fig.
Page 18
Installation steps Fig. 9 Fig. 10 Step 8: Slide the sensor bracket over the foot of the bed. When the sensor touches the trampoline (Figure 9), it should be in horizontal contact with the jumping cloth. Tighten the triangular screws on the sensor bracket (Figure 9). Insert the computer into the sensor holder.
Need help?
Do you have a question about the A71-034V01 and is the answer not in the manual?
Questions and answers