Table of Contents
Advertisement
READ AND UNDERSTAND
ALL
INSTRUCTIONS
1
.
KNOW YOUR POWER TOOL.
Safe
operation
of
this
power
tool requires that you read and
understand
this operator's manual and
all labels affixed to
the
tool. Learn its applications and limitations as
well
as
the potential
hazards.
A
WARNING
When using electric tools, basic safety
precautions
should always be followed
to
reduce
the risk
of fire,
electric shock, and personal injury. use common
sense. Some of these basic safety precautions
include the following:
SAFETY PRECAUTIONS
2.
KEEP
GUARDS
lN
PLACE and in good working
order.
3.
REMOVE ADJUSTING KEYS
AND WRENCHES.
Get in the habit of checking to see that hex
keys
and adjusting wrenches are removed from the tool
before turning it
on.
4.
KEEP THE WORK
AREA CLEAN. Cluttered work
areas and work benches invite accidents.
5.
DO
NOTUSE
lN DANGEROUS
EM/IRONMENTS.
Do
not use power tools neargasoline
or
otherflammable
liquids, in
damp or wet locations, or expose them
to
raiin.
Keep
the
work area well
lighted.
6.
KEEP CHILDREN AWAY FROM POWER TOOLS.
All visitors should
be
kept
at a
safe distance from the
work
area.
7.
MAKE
THE
WORKSHOP
CHILDPROOF wih
padlocks
and master switches or
by
removing starter
keys.
8.
DO NOT FORCE THE
TOOL.
lt
will
do the
job better
and
safer at the rate for which
it
was designed'
9.
USE.THE RIGHT TOOL. Do not force the tool or
attachment
to do
a
job
for
which
it
was
not
designed.
10.
USE
PROPER EXTENSION CORD. Make
sureyour
extension cord is in good condition. When using
an
extension cord,
be
sure to use one heavy enough
to
carry the current your product will draw.
A
wire gage
13.
'14.
15.
16.
17.
11.
12.
18.
19.
23.
24.
size (A.W.G.) of at least 16 is recommended for
an extension cord 100' or less in length. A
cord
exceeding 100' is not recommended.
WEAR PROPER APPAREL. Do not wear
loose
clothing, gloves, neckties,
rings, bracelets,
orother
jewelry
that
could
get
caught
in
moving parts' Non-
slip footwear
is
recommended.
Wear protective
covering over long
hair.
ALWAYS
WEAR
SAFEW
GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact
resistant lenses; they are
not safety
glasses.
PROTECT YOUR LUNGS. Wear
a face or dust
mask
if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear ear muffs or
plugs
during periods of
extended
use.
SECURE
THE
WORK.
Use clamps or
a
vise to hold
the work when practical. lt's safer than using your
hand and frees both hands to operate the
tool.
DO NOT
OVERREACH. Keep properfooting and
balance at
alltimes.
MAINTAIN THE
TOOLWITH CARE. Keep blades
sharp and clean
for the
best
and
safest
performance. Follow instructions
for
lubricating
and changing accessories.
DISCONNECT POWER TOOLS
BEFORE
SERVICING or before changing accessories such
as blades, bits and cutters.
REDUCE THE RISK
OF
UNINTENTIONAL
STARTING. Make sure switch
is in the
OFF
position before plugging in the tool.
USE
ONLY
THE
MANUFACTURER'S
RECOMMENDED ACCESSORIES. Consult this
operator's manual
for
recommended accessories.
Using
improperaccessories may
cause
riskof
injury.
NEVER STAND ON
TOOL. Serious injury
could
occur
if
the tool is tipped
or if the
blade
is
unintentionally contacted.
PERIODICALLY CHECK FOR WORN
OR
DAMAGED
PARTS. Check
for
alignment
of
moving
parts, binding
of moving parts,
breakage
of
parts,
loose mounting brackets, and any other conditions
that may afiect operation. A guard
or any
other part
that is damaged should be properly repaired or
replaced. Before the tool is used again, make sure
that the repaired or replaced part is
operating
properly and performing its intended function.
NEVER LEAVE TOOL RUNNING UNATTENDED.
Turn the power off. Do
not
leave tool until
it
comes
to a complete
stoP.
DO NOT ABUSE CORD. Never yank the cord to
disconnect
it
fom
the receptacle. Keep the cord
from
heat, oil, and sharp edges.
'
KEEP BITS CLEAN AND SHARP' Sharp bits
minimize stalling. Dirty and
dull bits
may
cause
misalignment
of
the material and possible operator
injury.
20.
21.
22.
A
WARNING
Do not connect your drill press to
a
power source
untilyou
have assembled and adjusted the drill press
as
described
in
this
manual and have read
and
understood all precautions and operating instructions
in
the manual and printed on the tool.
25.
Advertisement
Table of Contents
