Related Manuals for Elo TouchSystems WALLABY PRO
Summary of Contents for Elo TouchSystems WALLABY PRO
- Page 1 ASSEMBLY INSTRUCTIONS, WALLABY PRO COUNTERTOP STAND © Copyright 2023 Elo Touch Solutions, Inc. UM600620 Revision B...
- Page 2 Warning: Elo recommends using hand tools to assemble the Wallaby Pro. The use of power tools may result in damage to the product. Recommended Assembly Torque Thread Torque 6 in-lb (0.7 N-m) 12 in-lb (1.4 N-m) 26 in-lb (3.0 N-m) 46 in-lb (5.2 N-m) ©...
- Page 3 Contents for Kits: E989127 / E534273, Wallaby Pro Self-Service Countertop Stand Printer Door (ADA) Bag VESA Spacer and Screws Bag Qty. 1 VESA Spacer Qty. 1 Printer Door (ADA) Screw, M3x6, Pan Screw, M4x6, Pan Head, AudioNav Qty. Qty.4 Head, Cross...
- Page 4 Contents for Kits: E990079 / E534663, Wall Mount Kit for Wallaby Pro Countertop Stand Cables (E990079 only) Qty.1 Cable, 0.5m C13 to NA Qty.1 Cable, 0.5m C13 to EU Qty.1 Cable, 0.5m C13 to UK Wallmount Bracket Qty. 1 © Copyright 2023 Elo Touch Solutions, Inc.
- Page 5 Backer Board Install (Optional) Note: For wallmount installs, skip to step 57. Place stand in final install location. Level base plate by Install backer board (P/N E990854) to stand by removing eight screws adjusting feet (turning it counter-clockwise lowers the on back cover (discard screws and back cover) and installing backer foot, turning it clockwise raises the foot).
- Page 6 Android I-Series Note Display Orientation Unscrew display door captive thumbscrews. Open door and engage prop in hole. Next mount the display. Remove cable cover doors from display. Attach VESA Spacer to back of display using 14mm screws from “VESA For Android I-Series displays, proceed to step 4. Spacer and Screws”...
- Page 7 Windows I-Series 2.0 Display Cable Cover Note Display Orientation For Windows I-Series 2.0 displays, it is necessary to install the power Attach VESA Spacer to back of display using 22mm adapter to the display before attaching the VESA adapter. screws from “VESA Spacer and Screws” bag. Note display orientation and use correct mounting holes for Remove the display cable cover.
- Page 8 I-Series 3.0 with Intel® 2402L/2403LM/2702L/2703LM Monitors Note Note Display Display Orientation Orientation Attach VESA Spacer to back of display using 18mm Remove cable cover doors from display. Attach VESA screws from “VESA Spacer and Screws” bag. Note Spacer to back of display using 18mm screws from “VESA display orientation and use correct mounting holes (“All Spacer and Screws”...
- Page 9 2470L/2770L Monitors Note Display Orientation Remove mylar screw covers & four screws from back of Loosely install two pan head screws from display. Attach VESA Spacer to back of display using “VESA Spacer and Screws” bag in upper 14mm screws from “VESA Spacer and Screws” bag. Note threaded holes of VESA Spacer.
- Page 10 Upper mounting holes (24”/27” displays) Lower mounting holes (22” displays) Assemble display to display door. Use upper set of keyholes for 24” or 27” For 2470L/2770L monitors, skip to the next step. displays. Use lower set of keyholes for 22” displays. Install two additional pan For displays with separate power supply, install power head screws from “VESA Spacer and Screws”...
- Page 11 For 2470L/2770L monitors, an IEC C13-to-AC adapter For E534273 stand model, power strip is not included. is required to connect to the power strip. For North Mount power strip to bracket using included large cable America, StarTech P/N PAC100 is recommended. ties.
- Page 12 If using monitor, connect HDMI cable to monitor and route into stand as shown, for connection to compute module later. Connect If using I-Series, route USB-A cable from USB hub to I- USB-A to USB-B cable to monitor and to USB hub. Use cable ties to Series.
- Page 13 Disengage printer door latch by sliding upward. Pull Remove middle cover by loosening two screws, then printer door open. rotating cover out and pulling down. © Copyright 2023 Elo Touch Solutions, Inc.
- Page 14 For E534273 model, power cable is not included. Purchase a 1.8m to 5m (depending on length needed) C13-style power cable for your region. For E989127 model, choose correct 4.5-5.0m power cable (NA/EU/UK) from the included cables. If routing power from remote wall outlet, route power cable from wall outlet through base, and access hole in rear of printer bay, and...
- Page 15 Storm AudioNav or Assist Button Kit Installation I-Series Monitor (if not installing either, skip to step 26) Remove door cover screw shown. Slide printer door cover out and down to remove. For Assist Button Kit, skip to step 30. Install AudioNav Printer Door by guiding tabs into If routing LAN cable from wall source, route cable through base,...
- Page 16 Note: This stand supports AudioNav 6-key keypads (not included). MiniUSB cable required (StarTech USB2HABM6LA suggested). Install Assist Button Kit (Elo P/N E284334) by guiding tabs into holes in door, then sliding inwards. Reinstall screw as shown. Connect USB cable to AudioNav. For AudioNav –ALT or –ALTP part numbers, install the AudioNav device using screws from “AudioNav Screws (Long)”...
- Page 17 Route USB cable under lower bracket, up to USB hub. Tie off cable using cables ties, where indicated by blue arrows. © Copyright 2023 Elo Touch Solutions, Inc.
- Page 18 Printer Installation (If not installing printer, skip to step 40) Bracket 1 Bracket 4 Bracket 2 Bracket 3 Each printer requires a different bracket configuration. Brackets 1 and 2 are shipped installed in the printer cage. Brackets 3 and 4 can be found in the “Printer Hardware”...
- Page 19 Epson M30/Epson EU-M30 Installation Remove rear cable cover from printer. Slide printer into cage. For M30ii or M30iii, or EU-M30, fasten printer using two T2.5x8 screws No changes are required to the printer cage. from “Printer Hardware” bag. Skip to step 38. For earlier M30 models, fasten printer using two T3x6 screws from “Printer Hardware”...
- Page 20 Star mC-Print3 Installation Bracket 1 Bracket 4 Remove rear cable cover from printer. Slide printer into Remove Bracket 1 from cage by removing four screws, cage. and replace with Bracket 4 from “Printer Hardware” bag, Fasten printer using two T3x6 screws from “Printer using the same four screws.
- Page 21 Star TSP100/Star TSP654 Installation Bracket 1 Bracket 3 Bracket 2 Remove Brackets 1 and 2 from cage by removing eight Assemble printer to cage and install two T3x12mm screws screws. Assemble Bracket 3 (from “Printer Hardware” from “Printer Hardware” bag into screw holes marked “1”. bag), using screw position “A”...
- Page 22 Bixolon SRP-350/ Bixolon SRP-350/Epson TM-T88 Installation Bracket 1 Bracket 3 Bracket 2 Remove Brackets 1 and 2 from cage by removing eight screws. Assemble Bracket 3 (from “Printer Hardware” Assemble printer to cage and install four T3x6mm screws bag), using screw position “B” and four of the screws. from “Printer Hardware”...
- Page 23 Epson L90 Installation Epson TM-T88 Bracket 2 Assemble printer to cage and install four T3x6mm screws Remove Bracket 2 from cage by removing four screws. from “Printer Hardware” bag, using screw holes marked “2”. Skip to step 38. © Copyright 2023 Elo Touch Solutions, Inc.
- Page 24 Epson L90 Installation If printer includes a DC power supply, remove AC cable from power supply, and install power supply in middle bay as shown. Secure power supply with velcro strap. Use the included 0.3m power cable (either C5 or C13, depending on the printer power supply) to connect the power supply to the power strip.
- Page 25 Depending on printer type, route USB cable from printer Reinstall printer cage by inserting tabs in cage into slots in to USB hub, or route LAN cable to printer from bracket, and tilting cage into position, ensuring that wall/ceiling. Depending on power cable, route DC power cables are not pinched.
- Page 26 Printer Paper Chute/Filler Configuration Bracket Hook Configure printer paper chute/filler by removing two screws, replacing (per instructions below), and reinstalling screws. Chute 1 is pre-installed from the factory. Other chutes/filler are included in “Printer Hardware” bag. Reinstall middle cover. First slide hooks on left and right sides of Epson TM-T88, M30, EU-m30, L90: No change needed.
- Page 27 (Optional, if not installing skip to step 50) Note: Only one of the above options can be installed at a time. For Wallaby Pro EMV Cradle (P/Ns E990468, E996512, E990654, E990282) installation, remove side cover plate by removing two Remove backpack bracket by removing three screws.
- Page 28 NUC mounting holes Fasten Android Backpack to bracket using four screws from “Android Backpack Screws” bag. Remove AC power cable from Android For NUC, attach using two M3x8 screws (not included), at Backpack/NUC/Android Expansion Module power supply. circled locations. Install power supply in left bay. Use the included 0.3m C5 or C13 power cable to connect the power supply to the For Android Expansion Module, attach using screws power strip.
- Page 29 Android Backpack only: For Wi-Fi signal improvement, remove 2 Make the following connections for Android Backpack: rubber plugs circled. -DC cable from power supply Install male threaded end of one SMA extension cable into each -USB-A cable from USB hub hole and tighten nut to secure cable to stand.
- Page 30 Wallaby EMV Cradle Installation (Optional, if not installing skip to step 56) Note: Wallaby EMV Cradle kit P/Ns listed below are not compatible with ECMG4. 22” 24” 27” 22” 24” 27” For Wallaby EMV Cradle kits (P/Ns E352169, E458797, E458992, Reinstall backpack bracket by sliding left side of bracket E920661), add two screws to backpack bracket from EMV kit bag onto pins and tilting into position.
- Page 31 ECMG4 Installation (Optional) Assemble EMV Arm to backpack bracket. Add two screws from EMV kit bag “P” at rightmost position, and tighten Discard backpack bracket. Attach ECMG4 Bracket by two left screws to secure EMV Arm to backpack bracket. partially unscrewing two screws shown, sliding bracket Complete EMV assembly starting at step 5 of EMV Cradle into position, then tightening screws.
- Page 32 ECMG4 Installation (Optional) For Wi-Fi signal improvement, remove 2 rubber plugs circled. Connect ECMG4 power cable and LAN cable to ECMG4. Install male threaded end of one SMA extension cable into each hole and tighten nut to secure cable to stand. Slide ECMG4 down, behind ECMG4 bracket.
- Page 33 Push up on prop to disengage. Make the following connections to ECMG4: Close display door and tighten thumbscrews. -USB-A cable from USB hub Lock display door using key if access control is required. -HDMI cable from display. Assembly is complete. ©...
- Page 34 Centerline Wall Mount (Optional, requires kit P/N E990079 or E534663) Blocking Electrical box (optional) Blocking Blocking Remove eight screws to remove back cover. Discard screws and back cover. Prepare wall for mounting (see dimensional drawing MS603018 for details). Install blocking and optional electrical Remove four screws to remove base plate.
- Page 35 Centerline Mounting screws to attach bracket to wall (not included) should If routing power/LAN from external wall socket, route cables through be at least M4 (#6) or larger (pan head type). Install top two hole in bottom of stand. Unsnap grommet from wall bracket, and slide screws symmetric to centerline, leaving a 1/8”...
- Page 36 Learn more about Elo at EloTouch.com. Americas Europe (EMEA) Asia Pacific Tel +1 408 597 8000 Tel +32 16 930 136 Tel +86 (21) 3329 1385 EloSales.NA@elotouch.com EMEA.sales@elotouch.com EloAsia@elotouch.com The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose.