Page 4
i-on40 & i-onEX Range Viewing the Log ............56 Testing the System ............ 58 Sirens & Sounders............58 Keypad ................61 Walk test ................ 62 Outputs ................64 Remotes and Two-way Keyfobs ......... 65 Radio Hold Up Alarms ............67 Proximity Tags ..............
Page 5
i-on40 & i-onEX Range Compliance Statement The i-on50EX and i-on160EX: Are suitable for use in systems designed to comply with PD6662:2010 at Grade 2, Grade 3 and environmental class II. Are suitable for use in systems designed to comply with the requirements of EN50131-3 at Grade 2, Grade3 and environmental class II.
Page 6
i-on40 & i-onEX Range This page is intentionally blank. Page vi...
i-on40 & i-onEX Range 1. Introduction At the heart of the i-on range systems are the control units, their expanders and keypads. The control unit contains the main processing unit, the power supply and stand-by battery. The stand-by battery can keep the alarm system going for several hours if the mains supply fails.
Page 8
1. Introduction i-on40 & i-onEX Range 1. Two-button Hold Up Alarm with tilt switch. 2. Two button Hold Up Alarm. 3. Four button remote control. 4. Two-way remote control. 5. Keypad (i-kp01). 6. Keypad (KEY-K01, KEY-KP01 or KEY- KPZ01) 7. Wireless arming station. 8.
i-on40 & i-onEX Range 1. Introduction This guide covers four types of i-on control unit: the i-on30EX, i-on40, i- on50EX and the i-on160EX. A complete system using one of these control units comprises: Control unit i-on30EX i-on40 i-on50EX i-on160EX Fixed detectors External Siren/Strobe Users Portable 4-button remote...
1. Introduction i-on40 & i-onEX Range detectors that monitors a different area. The highest security level is called Full Set, and includes all the detectors. There are three other security levels called Part Set B, C and D. For example, in a small shop Full Set might monitor the whole premises, while Part Set B might monitor just the store room.
i-on40 & i-onEX Range 1. Introduction The Installer may also be able to call into your control unit and program it remotely. Depending on how your Installer has programmed the system you may receive a phone call from them requesting you to give them access to your alarm system.
1. Introduction i-on40 & i-onEX Range Controls and Displays Figure 2 shows the controls and displays available on the two styles of keypad. i-KP01 KEY-K01 KEY-KP01 KEY-KPZ01 1. LCD display . 2. Programming keys. Also used to gain access to programming menus and acknowledge alerts.
i-on40 & i-onEX Range 1. Introduction Controls: Full Sets the system. (All detectors in use.) In a partitioned system this key’s function can be programmed by the installer. B, C Part Set the system. (Some of the detectors in use.) In a and D partitioned system their function can be programmed by the installer.
Page 14
1. Introduction i-on40 & i-onEX Range (The top line of the display may show the installer’s name instead of “i-on160”.) To draw your attention to special events the navigation key glows red. On an i-kp01 there are four LEDs to the right of the programming keys.
i-on40 & i-onEX Range 1. Introduction The reason for this is that an installer may connect several detectors together to guard one “zone” (an area of a building for example). The control unit cannot tell that this has happened, so it is easier for the keypad to report an alarm from a “zone”.
1. Introduction i-on40 & i-onEX Range Guard A guard can only unset the system when it is in alarm, reset it, and then set the system again. A guard cannot change their own access code or add/remove another user. In a partitioned system the guard can be allocated to one or more partitions, which are the only parts of the system that they can set and unset.
Eaton’s Security Business recommends that you change the default access code as soon as possible (see page 40). Codes 0000 (or 000000) to 9999 (or 999999) are available but Eaton’s Security Business recommends that you avoid easily memorised codes such a 0000, 999999 or 654321.
1. Introduction i-on40 & i-onEX Range 90s. Note that the system will log the fact that someone has locked the keypads in this way by recording “Excess keys tamper”. If your alarm system is connected to an alarm receiving centre then the control unit will send a signal to the centre as a result of the tamper alarm.
i-on40 & i-onEX Range 1. Introduction Figure 4 shows you where they are. Unset Set LED Unset LED Query LED Part set LED Query Part Set (programmable) Figure 4. Two-Way Key Fob Buttons Operating the buttons To ensure that the fob does not accidentally operate while it is in your pocket, the buttons are deliberately slow to respond to pressure.
Page 20
1. Introduction i-on40 & i-onEX Range Lock Figure 5. HUA Buttons HUA With A Two-Way Key Fob It is possible to start a Hold Up Alarm from a two-way key fob. However, the Installer must enable this within the control unit. (Note that doing so will mean that the system no longer complies with BS8243 or DD243.) Once the Installer has enabled this feature, a Master User must also turn this facility on, see page 101.
i-on40 & i-onEX Range 2. Alarms The table below shows the different kinds of alarms possible. Type of Signal Started by: Alarm Intruder Loud warbling tone Normal alarm or entry route zone from siren. activated when system is set. 24 hour zone activated at any time. Fire Pulsing tone from Fire zone activated at any time.
2 Alarms i-on40 & i-onEX Range Silencing an Alarm In an alarm the sirens run for a limited time set by the installer (a maximum 15 minutes for intruder, Hold Up, and tamper alarms). If you return to the system while the sirens are running you can silence the siren as follows: Make sure it is safe to enter the premises:...
i-on40 & i-onEX Range 2. Alarms Press or and key in your user code to see the name of the zone (if the installer has programmed one), for example: Press to restore the display to ...
2 Alarms i-on40 & i-onEX Range Press to clear the message and the display returns to normal. The LEDs around the navigation keys remain red. Call your alarm company and tell them that an alarm has occurred. When you talk to the alarm company, they will ask about the circumstances of the alarm, and also for the code you recorded from the display.
i-on40 & i-onEX Range 2. Alarms Function ‘5’ End this call (and let the control unit contact the other nominated persons for this alarm) Play ‘Home’ and ‘alarm’ message again ‘3’ ‘9’ Clear down (and do not call any of the other nominated persons for this alarm).
2 Alarms i-on40 & i-onEX Range OR: Press . The rim of the navigation pad will stay red and the system will show the text of the alert the next time you key in an access code. (The keypad will stop beeping.) Note: 1.
i-on40 & i-onEX Range 3. Setting and Unsetting There are two main ways of setting and unsetting your alarm system: either from a keypad or from a remote control. This chapter is split into two halves, dealing with each of those methods in turn. In case you are not familiar with some of the terms used in this book: “Full Set”...
3. Setting and Unsetting i-on40 & i-onEX Range Setting 1. Starting to Set Do this: The display shows: Make sure the system is idle. Secure all the windows and doors. (The top line may show the installer’s name.) ...
Page 29
i-on40 & i-onEX Range 3. Setting and Unsetting The bottom line of the display shows each item from the rest of the menu in turn. Press . Go to: 3. Finishing Setting on page 24. Partitioned Systems Do this: The display shows: ↕...
Page 30
3. Setting and Unsetting i-on40 & i-onEX Range Partitions to which you have access. Note that the installer may have given the Partition a name, for example “Stores”. this will appear on the display instead of the partition number. ↕ ...
Page 31
i-on40 & i-onEX Range 3. Setting and Unsetting Timed Exit: The keypad sounds the exit tone (a continuous tone). The top line of the display shows the part of the system being set, the bottom line shows the remaining exit time (in seconds).
Page 32
3. Setting and Unsetting i-on40 & i-onEX Range Final Door Set: The keypad sounds the exit tone (an interrupted tone if the final exit door is open, a continuous tone if the exit door is closed). The top line of the display shows the part of the system being set, the bottom line shows “Final Door...
i-on40 & i-onEX Range 3. Setting and Unsetting (The keypad may show the name of the installer instead.) In a part set system, one of four LEDs glows to show which part of the system is set. Note: The installer may have disabled the LEDs to ensure that the alarm system meets the appropriate standards.
3. Setting and Unsetting i-on40 & i-onEX Range If you try to set when one or more detectors are still active then the bottom line of the display tells you which zone is active, for example the back door - see Figure 6. SETTING:PARTITION 1 Z041 A Back door Figure 6.
i-on40 & i-onEX Range 3. Setting and Unsetting Override by: Message Meaning Grade 2 Grade 3 A Hold Up Alarm device is Installer Installer still active. (If a user has forgotten to reset the device an installer is not required.) ...
Page 36
3. Setting and Unsetting i-on40 & i-onEX Range Start the Entry Procedure Do this: The display shows: Enter by the designated entry door or route. (This usually the last through which you leave the premises.) Go directly to the keypad. The system starts the entry timer.
i-on40 & i-onEX Range 3. Setting and Unsetting Using Radio Keypads and Remote Controls. Using a Radio Keypad Setting Secure all your windows and doors. Make sure the system is in standby, and that you can hear the warning tones from the sounders. Key in a valid access code (or present your proximity tag).
3. Setting and Unsetting i-on40 & i-onEX Range “ Proximity tag sensor Transmit” LED Figure 7. Radio Keypad Note: The radio keypad does not show the status of the alarm system at all. The left hand “Transmit” LED glows only to show that the keypad is sending a command to the control unit.
i-on40 & i-onEX Range 3. Setting and Unsetting Complete setting using the method programmed by the Installer (see “3. Finishing Setting” on page 24). Unsetting Enter by the designated entry door. Press on your remote control. The system unsets. At this point the system displays the standby screen. Note: Your administrator may have programmed the control unit so that you cannot unset the alarm system using a remote control.
Page 40
3. Setting and Unsetting i-on40 & i-onEX Range Note: If the Installer has programmed the system to complete setting by Lock Set (see page 26) then you must go to the designated lock and lock it in order to complete the setting process. The setting LED glows green for three seconds.
Page 41
i-on40 & i-onEX Range 3. Setting and Unsetting Querying the State of the System Press and The query LED flashes red three times. hold: The control unit sends a message to the fob giving the current state of the system. If the system is: Full Set, you see a green Set LED: Part Set, you see a green Part Set LED:...
i-on40 & i-onEX Range 4. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what type of user you are: Master User, Admin User or Normal User. A Master User has access to all the options of the Menu.
i-on40 & i-onEX Range 4. Administration Editing Text For many of the items that you can program, the control unit lets you assign a 12 character name. To key in text for the name press each number key one or more times to obtain the letter you want (the letters of the alphabet appear on the keys in the same arrangement as on many mobile phones, see Figure 9.) Press # to change between capitals and lower case letters.
Page 44
4. Administration i-on40 & i-onEX Range Press Key in your access code (or present a tag). Press . The bottom line of the display shows the first of a list of zones that you may omit. (Either as a zone number or as a name, if the Installer has programmed one for the zone.)
i-on40 & i-onEX Range 4. Administration The control unit allows you to omit a zone for one setting/unsetting cycle. You will have to omit the zone again for the next setting/unsetting cycle. Users The i-on160EX control unit can recognise up to 500 individual users. The i- on50EX can recognise up to 100 users, while the i-on30EX and i-on40 can recognise up to 50 users.
4. Administration i-on40 & i-onEX Range Editing Existing Users This menu lets you change the details for an existing user. Note that you cannot edit a user when the partition they belong to is set. Name Use this option to give the user a name up to 12 characters long. ...
Page 47
i-on40 & i-onEX Range 4. Administration Press . The bottom line shows: 10. Press . The display shows the current name given to the user, and places a cursor at the beginning of the name. ...
Page 48
4. Administration i-on40 & i-onEX Range the first in a list of the users already programmed into the control unit. In the example shown the name is “User 001”. Press or to display the user you wish to edit. (Alternatively, if you already know their user number, you can key that in and the display will show that...
Page 49
i-on40 & i-onEX Range 4. Administration Press Key in your access code (or present a tag). Press . Press . Press . Press . The bottom line of the display shows the first in a list of the users already programmed.
Page 50
4. Administration i-on40 & i-onEX Range 13. Press to change a “Yes” to a “No” or back again. See page 4 for a description of partitions. See Note below for a quick way of assigning users to partitions.
Page 51
i-on40 & i-onEX Range 4. Administration Press . If you are a Master or Admin User: (otherwise go to step 6) Press . Press . Press . Press or . until the bottom ...
Page 52
4. Administration i-on40 & i-onEX Range confirmation tone. The keypad display shows: If a user forgets their code then a Master or Admin user must delete that user from the system (see page 55), and recreate a new user with a new code (see page 52).
Page 53
i-on40 & i-onEX Range 4. Administration If you are a Normal User: Press . Press until the display shows: Press . Note: If you have a prox tag allocated to you then the screen will display “Delete Prox Tag?”.
Page 54
4. Administration i-on40 & i-onEX Range Press . If you are a Master or Admin User: (otherwise go to step 6) Press . Press . Press . Press or . until the bottom ...
Page 55
i-on40 & i-onEX Range 4. Administration Press any button on the device that you wish to register. Hold the button down until you see the transmit LED flash. The keypad gives a double “beep” confirmation tone. The keypad display shows: ...
Page 56
4. Administration i-on40 & i-onEX Range Press . Press . Press . Press or . until the bottom line of the display shows your own user name or number. Press . ...
Page 57
i-on40 & i-onEX Range 4. Administration The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit has learned the identity of the Hold Up Alarm and linked it with your access code. You cannot register more than one radio HUA per user. If the control unit has already learned that radio HUA then you will hear a low tone and the display will show the message “Hold Up Alarm already in use”.
4. Administration i-on40 & i-onEX Range Press . Press or until the bottom line shows the device you wish to delete, for example: Go on to step 8. If you are a Normal User: ...
Page 59
i-on40 & i-onEX Range 4. Administration To add a new user: Make sure the display shows the standby screen. Press Key in your Master User or Admin access code (or present a suitable tag). ...
Page 60
4. Administration i-on40 & i-onEX Range Press or to scroll through the list of partitions. On the bottom line of the display “Yes” means that the user is assigned to the partition, “No” means that the user is not assigned to the partition.
i-on40 & i-onEX Range 4. Administration Note: A Duress user cannot have a remote control or radio HUD. The display finally asks you to press both buttons on any radio HUA that you want to assign to the new user. 13.
4. Administration i-on40 & i-onEX Range Press . The bottom line of the display shows the first user in a list of the users recognised by the system. Press or . until the bottom line of the display shows the user you ...
Page 63
i-on40 & i-onEX Range 4. Administration Key in your access code (or present a tag). Press until you see:. Press . The display shows the most recent event recorded in the log. Press to see a more detailed description of the event.
4. Administration i-on40 & i-onEX Range Testing the System If you think that your system is not working correctly then a Master User or Admin User can use the Test option to test various peripherals. If the test confirms that part of the system is not working then contact your installer. The Test option also lets you check the identity of Remote controls, Hold Up Alarms and Tags.
Page 65
i-on40 & i-onEX Range 4. Administration Press again to turn the sirens off. The keypad gives a double “beep” confirmation tone. The keypad display shows: Press when you have finished this test. The display shows: ...
Page 66
4. Administration i-on40 & i-onEX Range The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit sounds a test tone on the loudspeakers. Check that you can hear them. Press again to turn the loudspeakers off.
i-on40 & i-onEX Range 4. Administration Keypad Make sure the display shows the standby screen. Press Key in your access code (or present a tag). Press until you see: Press . ...
4. Administration i-on40 & i-onEX Range Walk test The Walk Test menu allows you to test detectors without starting an alarm. To “walk test” an alarm system you operate each detector in the system. If the detector is working the control unit sounds a confirmation tone and flags that the detector has passed the test.
Page 69
i-on40 & i-onEX Range 4. Administration Press . to see the first of the walk test options: The Walk Test menu provides three options to give different ways of organising a walk test. The options within Walk Test are: System This option allows you to walk round the entire system and test all the zones.
4. Administration i-on40 & i-onEX Range 11. Press if you want to see a list of the zones that have not yet been tested: 12. Press or to scroll up or down the list. ...
i-on40 & i-onEX Range 4. Administration presses is the same for all i-on control units. Press or to display the output you wish to test. Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: ...
Page 72
4. Administration i-on40 & i-onEX Range Key in your access code (or present a tag). Press until you see:. Press . The display shows: Press until you see: Press . ...
i-on40 & i-onEX Range 4. Administration Press all the other buttons on the device. Each time you press a button on the remote the keypad gives a double “beep” confirmation tone. For each button you press you will see a similar message, for ...
Page 74
4. Administration i-on40 & i-onEX Range Press . The display asks you to press both buttons on the radio HUA you wish to test. If there are no radio HUAs available the display briefly shows: Press and hold down both buttons on the Hold Up Alarm you wish to test (you should hold the buttons down until the transmit LED on the...
i-on40 & i-onEX Range 4. Administration Proximity Tags Make sure the display shows the standby screen. Press Key in your access code (or present a tag). Press until you see:. Press . ...
4. Administration i-on40 & i-onEX Range If the control unit does not recognise a prox tag, the display shows: Press to end the test. ARC Reporting If your alarm system is connected to an Alarm Receiving Centre by telephone line then there may be a time when they or the installer ask you to test the line.
i-on40 & i-onEX Range 4. Administration System Configuration The System Configuration option allows you to change some parts of the system to suit your particular needs. If you need more extensive changes to the operation of the system then you must contact your installer. Switching the Chime On/Off The installer may have set up your alarm system to give a chime tone whenever something triggers one or more detectors while the system is...
4. Administration i-on40 & i-onEX Range Allowing Remote Access It is possible for the Installer to gain access to the control unit of your alarm system remotely. They can do this from their PC either over the telephone network or through a network cable connected directly to the control unit. (If your alarm system uses an i-on30EX or i-on30EXD then note that it cannot communicate over a network cable.) When the control unit is delivered from the factory this facility is turned off.
i-on40 & i-onEX Range 4. Administration Press when you have finished making changes. The keypad gives a double “beep” confirmation tone. The keypad display shows: Setting the Date and Time You will need to re-program the date and time if the control unit loses power for an extended time, and the battery is exhausted.
4. Administration i-on40 & i-onEX Range of the display shows the current system time. The minutes are highlighted. 10. Key in the correct time. Use the 24- hour clock in the format hh/mm. If the hours or minutes are “9” or less ...
Page 81
i-on40 & i-onEX Range 4. Administration A warning time, during which a warning tone can sound before the system sets. A warning tone, which the system can give during the warning time. Each exception marks a time period when certain events do not apply. An exception has a start time and date, an end time and date, and a name.
Page 82
4. Administration i-on40 & i-onEX Range In a partitioned system the keypad display shows a list of partitions. Press or to scroll through each partition. Press or to select one of the actions: Full Set, Part Set or Unset. Alternatively, select “No” if you do not want the partition involved in the event.
Page 83
i-on40 & i-onEX Range 4. Administration its purpose when you are linking events to exceptions. Exception Start Time. Key in the start time in 24 hour format. Exception Start Date. Key in the starting day and month in number format (for example 31/12 for 31 December).
Page 84
4. Administration i-on40 & i-onEX Range Press to defer setting for 30 minutes. Note that the user must belong to the partition that is due to be set. Press the Menu key to gain access to the setting menu to set another partition that is not involved in the current setting event.
Page 85
i-on40 & i-onEX Range 4. Administration 2. If you are unsetting a partition and setting the same partition again then you must program the setting event to occur at least 10 minutes after the unsetting event. Calendar Set Example As an example, assume that you wish to set the alarm system every evening during the days Monday to Friday, and unset the alarm system every morning on Monday to Friday (leaving the system set over the weekend).
Page 86
4. Administration i-on40 & i-onEX Range 12. Key in the start time. In the example we want to make the whole day of the bank holiday an exception, so start at one minute past midnight. 13. Press . ...
Page 87
i-on40 & i-onEX Range 4. Administration To program the events: 20. Starting from where we finished adding the exception: 21. Press until you see: 22. Press . The display shows: 23. Key in a name to remind you of the ...
Page 88
4. Administration i-on40 & i-onEX Range confirmation tone. The keypad display shows: 31. Press until the display shows the partition that you want to set (or unset). Note: If you have a part setting system then this step will not apply. 32.
Page 89
i-on40 & i-onEX Range 4. Administration Friday, and sets partition 2 to Full Set. You don’t need to apply the exception, since the system will be set from Friday evening, and will not be unset on the bank holiday Monday morning. 38.
i-on40 & i-onEX Range 4. Administration Programming Outputs During programming the installer may allocate some outputs so that they can be reprogrammed by an Administrator. This section describes how the Administrator can use those outputs. For each output you can, if you wish, set an “on” time and an “off” time so that the output will go on and off at fixed times each day.
Page 91
i-on40 & i-onEX Range 4. Administration Note: The display on the i-on40 will look simpler for example: However, the sequence of key presses is the same for all i-on control units. Press or to display the output ...
Page 92
4. Administration i-on40 & i-onEX Range addition, you can program the output to come on and go off at fixed times (see the next section). “No”. The output goes on when a user turns it on, but then goes off again after a set time.
Page 93
i-on40 & i-onEX Range 4. Administration If you want to program a remote control to control the output, see page 93. To Program On and Off Times for Latched Outputs First make sure that the output you wish to use is programmed as Latched = Yes (see steps 1 to 16 starting on page 84).
Page 94
4. Administration i-on40 & i-onEX Range 24. Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: Note: If you do not wish the output to switch on and off at a set time then leave the “On Time”...
i-on40 & i-onEX Range 4. Administration 30. Press when you have finished making changes. The keypad gives a double “beep” confirmation tone. The keypad display shows: 31. Press to leave the menu. Note: You can switch the output on and off from the Menu by selecting Outputs On/Off (see page 105).
Page 96
4. Administration i-on40 & i-onEX Range Press . Press . EITHER Press the button on the remote control that you wish to program. Hold the button down until you see the transmit LED flash. Only the “*” button (Part set) is available on a FOB-2W-4B.
Page 97
i-on40 & i-onEX Range 4. Administration Press to select it. The display shows the first button on the remote control. Note: Only the “*” button (Part set) is available on a FOB-2W-4B. Press or to show the button ...
Page 98
4. Administration i-on40 & i-onEX Range you can apply to the selected button. The setting options available are: Part Set All Part Sets All Partitions that the user belongs to. Partitions You can choose to Part Set or Full Set any partitions that the user belongs to.
Page 99
i-on40 & i-onEX Range 4. Administration e) Press when you have finished making the changes you want. The keypad gives a double “beep” confirmation tone. The keypad display shows: 12. Press twice. If you want to program other user remotes repeat steps 8 to 11.
Page 100
4. Administration i-on40 & i-onEX Range Press . Press or . until the bottom line of the display shows: Go on to step 8. If you are a Normal User: Press . Press until the display shows: ...
Page 101
i-on40 & i-onEX Range 4. Administration Operate an Output To program a remote or two-way keyfob button to operate an output: Make sure the display shows the standby screen. Press Key in your access code (or ...
Page 102
4. Administration i-on40 & i-onEX Range registered remote controls and their users. Press or to show the remote control you want to edit. Press to select it. The display shows the first button on the remote control. Press ...
i-on40 & i-onEX Range 4. Administration that you can give to the button: “On” = Turns the output on. “Off” = Turns the output off. “Toggle” = Changes the state of the output every time you press the button. 14. Press or . until the display shows the action you want to give ...
Page 104
4. Administration i-on40 & i-onEX Range Press until the display shows: Press . Press until the display shows: Press . The display shows: 10. EITHER a) Press the button of the remote ...
Page 105
i-on40 & i-onEX Range 4. Administration 13. Press repeatedly to leave the menu. The control unit will let you delete all remote controls in one operation. Think carefully before you use this feature. To delete all remotes: Make sure the display shows the ...
4. Administration i-on40 & i-onEX Range Preventing Any Remote From Unsetting the System You may wish to prevent any remote from unsetting your alarm system. You can do this as follows: Make sure the display shows the standby screen. ...
i-on40 & i-onEX Range 4. Administration Allowing a FOB-2W-4B or 727r to start a HUA You may wish to allow a user to start a Hold Up Alarm from a 727r remote control or a FOB-2W-4B two-way fob. The Installer must first program the control unit to allow this (note that doing so will mean that the system no longer complies with BS8243 or DD243).
4. Administration i-on40 & i-onEX Range Once you have carried out this process, then a user with a Fob-2W-4B can start a HUA by pressing any two diagonally opposite buttons on their fob at the same time. Users with a 727r remote control must press the top and bottom buttons (A and ) at the same time.
i-on40 & i-onEX Range 4. Administration Press . The display shows: Followed by a series of progress messages: (Press if you decide you want to abandon the call.) The control unit calls the installer's computer on the number you selected.
Page 110
4. Administration i-on40 & i-onEX Range Press until the display shows the telephone number that you wish to change, for example: Press . The display shows the current phone number, for example: 10. Key in the new phone number. If necessary, press ...
i-on40 & i-onEX Range 4. Administration Turning Outputs On/Off You can operate the outputs from the keypad, as well as by using a remote control (provided the installer has assigned some outputs to you). To operate an output: Make sure the display shows the ...
4. Administration i-on40 & i-onEX Range What System Have I Got? There may be times, when your installer is helping you with a problem over the phone, that they ask you what system you have and what software version it is running. You can find this information as follows. ...
Page 113
i-on40 & i-onEX Range 4. Administration Press . Press . until the display shows: Press . The bottom line of the display shows the module type currently fitted (or the word “None” if no module is fitted).
i-on40 & i-onEX Range List of Menu Options Item Page Omit Zones Users Add User Edit User (for each user:) Name Type (not U01, U001) 41 Partitions (not in part setting system) Code Prox Tag Remote Hold Up Alarm Delete User View Log Test Siren &...
i-on40 & i-onEX Range Alarm Functions At a Glance Navigation: up, down, left, right HUA/PA keys Display shows: Time and date when system off (unset). First zone to alarm after alarm Read log here. Glowing = On (set) Off = Off (unset) Flashing = Part Set (part setting systems only) Key in access code...
i-on40 & i-onEX Range After an Alarm N ORDER TO O THIS HE SYSTEM WILL EITHER: Switch off siren: Stop the siren. The Key in ACCESS CODE keypad display shows the OR present tag. first zone to alarm. Press . Reset the system: Keypad display shows time and date.
Need help?
Do you have a question about the i-onEX Series and is the answer not in the manual?
Questions and answers