Denon UPO-250 Operating Instructions Manual page 18

N 0
oO
PROGRAMMED SELECTION
Example: Programming track 3 to play first, track 18 to play second, on e CO with 18 tracks and a total playing time of 62 minutes, 3
seconds
Playing Certain Tracks in any Desired Order .................
(Perform this operation from the remote contro! unit.)
Setting and Playing the Program (Set the Slide Switch to the "MAIN® Side.)
Press the PROGRAM button.
'@ 2.03."
Set track 3 to play first.
After 2 seconds
The display when track 3 is set to play first
Time of first track: 8 minutes, 00 seconds
Set track 18 to play second.
After 2 seconds
The display when track 18 is set to play second
Total time of tracks 1 end 2: 16 minutes, 05
seconds
Press the play button. beet — stert playing in the programmed
The numbers of the programmed tracks go off once the tracks are played.
The time display will read "—-—M ——S" if ® track number of 31 or higher is set in the program.
When a program is set during CD play after a direct selection, the track currently playing is set es the first track in the program.
Up to 20 tracks of your choice from among track numbers 1 through 99 can be programmed with this CD player.
If you attempt to set a track number that is greater than the number of tracks on the disc, that track number will not be displayed when
the buttons are pressed.
Programming is also possible when the disc tray is open. In this case, track numbers greater than the number of tracks on the disc can
be programmed, but these are ignored when the disc is played.
There is a silent interval of 4 seconds between tracks. This is has been designed to create a blank section of 4 seconds between
selections when recording programmed tracks onto tape.
@ The entire program is cleared when the disc tray is opened or closed (by pressing the & button).
If you make 8 misteke when programming tracks, press the CANCEL button and program again. (Each press of the CANCEL button
cancels the last track.)
An A-B section repeat is not possible during programmed play.
Other operetions possible during programmed play:
The quick search, pause, skip monitor, and other operations can be used during programmed play. To move to the beginning of the
previous track with the quick search operation, press 144 44 once, then once again while the time display reads 'O0u 0OQs.To
move to the beginning of the following track. press DP PPI once, regardless of the time display.
Perform programming and canceling in the stop mode.
18
seseesereneenssss | QUICK SEARCH |
@ Press the auto search forward button (D> PPI).
© Each press of the auto search forward button (D> PP)
moves the pickup to the beginning of following tracks.
@ Press the auto search backward button (#44 44).
© Each press of the auto search backward button (Hd 4¢)
during the search operation moves the pickup to the
beginning of previous tracks.
© Searching for Tracks While Listening to the Sound
e Use this to skip through a disc listening to the sound at high speed.
This function is convenient when searching for a certain section within a long track.
« Use the skip monitor function to find the desired position, then release the search button to start regular playback from there.
(2) Forward skip monitor
© The track number and elapsed playing time of the track being
skipped through are indicated on the display.
© Ifthe end of the tast track on the disc is reached while pressing
the search button, (33) appears on the display and the skip
monitor operation stops. To resume CD play, press the search
backward button (#€¢ 44) until (32) switches to the track
number, then perform a different operation.
@ During CD play, press and hold in the forward search button
{>> DDI to skip forward while listening to the sound.
[2] Backward skip monitor
© The track number and elapsed playing time of the track being
skipped through are indicated on the display.
© if the beginning of the first track on the disc is reached while
Pressing the search button, (C0) appears on the display and the
skip monitor operation stops. To resume CD play, press the
Search forward button ( >> PPI) until (CC) switches to the track
number, then perform 2 different operstion.
@ During CD play, press and hold in the backward search button
{844 44) to skip backward while listening to the sound.
if the forward or backwerd skip button is pressed di programmed CD play and ed at a track which has not been
programmed, the next pro: il ed once that track has been pI id to the end.
G)
m
Zz
m
wv
>
i=
7)
m
O)
=
e)
z