Subscribe to Our Youtube Channel
Related Manuals for Girard Systems 98GCK-36A
Summary of Contents for Girard Systems 98GCK-36A
- Page 1 AWNING CONTROL KIT 98GCK-36A RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com...
- Page 3 AC MOTOR CONTROLLER 98GC74 INSTALLATION and PROGRAMMING GUIDE Rev.12282015 RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com...
- Page 4 Shore Power – if connected; Generator Power – if the generator is running; Inverter Power – batteries must be charged for inverter operation. Girard Systems awnings are supplied with an electric motor appropriate to the product.
- Page 5 These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation.
- Page 6 INSTALLATION WIRING DIAGRAM...
- Page 7 WARNING ALL ELECTRICAL WORK MUST CONFORM TO APPLICABLE ELECTRICAL CODES AND STANDARDS. • Turn off power before beginning any electrical work. • Please consult your RV’s wiring diagram to locate any wiring prior to any drilling or any installation procedures. •...
- Page 8 pairing the module with a motor controller and behind the hole on the left is a Red LED which will illuminate when any of the buttons are pressed. L.E.D P2 Button Fig.2 When pairing with the 98GC74 it is advised that the awning to be controlled is manually extended couple of feet to enable the programmer to see if the awning is responding in the correct direction when the buttons on the wall switch are pressed.
- Page 9 PAIRING WITH A MOTION SENSOR Identify the Primary remote which operates the Motor controller for the awning on which the motion sensor is to be mounted. There may be more than one on the vehicle. Prepare the Motion Sensor for pairing by carrying out the following procedure. Remove the 2 small Phillips screws which secure the motion sensor...
- Page 10 Remove the 4 Phillips Magnet Base Plate screws holding the module together. Remove the base plate and silicone insert. Insert Fig.3 Turn the base plate over (Magnet down). Then Reed Switch place the motion sensor on top of it so that the magnet is aligned with the reed switch.
- Page 11 Once programming is complete, reassemble the Motion sensor module and mount it on the awning lead rail. For queries or assistance with programming any of your G-Link devices please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am and 5:00pm P.S.T.
- Page 12 DRY CONTACT MODULE GC1149A INSTALLATION GUIDE RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com...
- Page 13 Shore Power – if connected; Generator Power – if the generator is running; Inverter Power – batteries must be charged for inverter operation. Girard Systems awnings are supplied with an electric motor appropriate to the product.
- Page 14 These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation.
- Page 15 PRODUCT DESCRIPTION The GC1149A Dry Contact Module allows the user to interface their Dry Contact Systems (Crestron, Switch Input or RV-C) with our G-link Controllers. This module will accept Retract, Stop and Extend commands from the Dry Contact System and send an RF signal to any programmed G-link Controller or Remote Motor.
- Page 16 MODES OF OPERATION The GC1149A has 3 modes of operation; 1. Continuous Mode (Default) – A single press of a command button will allow the awning to fully extend or retract unless interrupted by the STOP button. 2. Step Mode (Selected) – The command button must be held down to allow the awning to fully extend or retract.
- Page 17 PROGRAMMING STEPS NOTE: • Before starting this procedure the Receiver must be without power (OFF) for at least 10 seconds. • During the programming function the interval between each step required must be less than 10 seconds 1. PROGRAMMING THE GC1149A TO A RECEIVER(GC136, GC154 or GC274A) a.
- Page 18 Note: If the motor turns in the opposite direction, repeat “a to e’ but now use Extend instead of Retract. For queries or assistance with programming any of your G-Link devices please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am and 3:30pm P.S.T.
- Page 19 12V MOTION SENSOR 98GC779G INSTALLATION & PROGRAMMING GUIDE RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com...
- Page 20 Shore Power – if connected; Generator Power – if the generator is running; Inverter Power – batteries must be charged for inverter operation. Girard Systems awnings are supplied with an electric motor appropriate to the product.
- Page 21 These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation.
-
Page 22: Installation Guidelines
INSTALLATION GUIDELINES The purpose of this device is to automatically send a signal to the motor controller of the fitted awning to fully retract the awning in windy weather conditions. In new installations the 98GC779 Motion sensor is preprogrammed at the factory. Replacement Motion sensors will need to be programmed. - Page 23 The cable of the Motion sensor points in toward the middle of the awning, and is connected by means of a water resistant connection as shown in the photographs below. Once connected the cable should be tied and secured neatly to the awning lead rail.
- Page 24 2 small Phillips screws securing the module to the mounting bracket and turning the module so that the cable is now to the left and the Girard Systems Logo is facing upward, and then replace the screws. So that this ….
-
Page 25: Motion Sensor And Led Connections
Motion Sensor and LED Connections 4 conductor power supply 3 conductor power supply... -
Page 26: Preparation For Pairing
Programming the Motion Sensor (98GC779G) Preparation for Pairing Remove the 2 small Phillips screws which secure the motion sensor to the mounting bracket. The base of the module is magnetized so will need to be gently lifted off. Fig.1 Then turn it over. Fig.2... - Page 27 Remove the 4 Phillips Base Plate Magnet screws holding the module together. Remove the base plate and silicone insert. Insert Fig.3 Turn the base plate over (Magnet down). Reed Switch Then place the motion sensor on top of it so that the magnet is aligned with the reed switch.
-
Page 28: Pair With 98Gc74 Motor Controller
Once programming is complete, reassemble the Motion sensor module and mount it on the awning lead rail. For queries or assistance with programming any of your G-Link devices please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am and 3:30pm P.S.T.
Need help?
Do you have a question about the 98GCK-36A and is the answer not in the manual?
Questions and answers