Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Girard Systems 98GCK-45DR
Summary of Contents for Girard Systems 98GCK-45DR
- Page 1 98GCK-45DR INSTALATION AND PROGRAMMING GUIDE REV.03092018...
- Page 2 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com Girard Systems awnings may be operated in light wind and rain conditions. When periods of heavy rain and or high wind are expected the awning must be closed.
-
Page 3: Product Description
These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation. - Page 4 WARNING “To reduce the risk of electric shock the operator power is to be provided from a weatherproof junction box in the case of permanent wiring, as per 314.15 of the National Electrical Code, NFPA 70.” To prevent the motor protector from tripping do not exceed 2 minutes of operation per hour.
- Page 5 PAIRING WITH REMOTE DEVICES The following pages give instructions on how to pair the GC1146C Motor controller with various compatable RF remote control devices. Please ensure that the correct set of instructions are followed for the device being paired with the Motor controller. 98GC1063 SINGLE CHANNEL HANDSET Fig.1 Fig.2...
- Page 6 3) Press the IN button on the handset. (The awning should retract) If the awning extends at this point instead of retracting, press the STOP button immediately, then remove the power supply to the motor controller for at least 10 seconds.
- Page 7 DRY CONTACT MODULE GC1149A Fig.1 Technical Specification • Input voltage ： 12V/24V • Transmitting frequency ： 433MHz • Transmitting power ： 10 milliwatts • Transmitting distance ： 500 Feet open area • 120 feet on two walls Page 7 of 14...
-
Page 8: Modes Of Operation
MODES OF OPERATION The GC1149A has 3 modes of operation; 1. Continuous Mode (Default) – A single press of a command button will allow the awning to fully extend or retract unless interrupted by the STOP button. 2. Step Mode (Selected) – The command button must be held down to allow the awning to fully extend or retract. -
Page 9: Programming Steps
PROGRAMMING STEPS NOTE: • Before starting this procedure, the Receiver must be without power (OFF) for at least 10 seconds. • During the programming function the interval between each step required must be less than 10 seconds 1. Programming the 98GC1149A a. - Page 10 PAIRING WITH A MOTION SENSOR GC779G Identify the Primary remote which operates the Motor controller for the awning on which the motion sensor is to be mounted. There may be more than one on the vehicle. Prepare the Motion Sensor for pairing by carrying out the following procedure. Remove the 2 small Phillips screws which secure the motion sensor...
- Page 11 Remove the 4 Phillips Magnet Base Plate screws holding the module together. Remove the base plate and silicone insert. Insert Fig.3 Turn the base plate over (Magnet down). Then place the motion sensor Reed Switch on top of it so that the magnet is aligned with the reed switch.
- Page 12 Note; when carrying out this part of the procedure each step must be executed within 6 seconds of the previous one or the module will revert to factory settings. It is highly recommended that you read and understand the following sequence before attempting to execute it. 1) Set the Motion Sensor Adjustment Dial to 0.
- Page 13 PAIRING WITH ADDITIONAL DEVICES As mentioned in the Product description the GC1146C can be paired with up to 20 compatible devices, wall switches handsets and others. The first device to be paired with the 98GC74 Motor Controller shall now be referred to as the PRIMARY REMOTE which is used to program all additional devices which shall be referred to as the SECONDARY REMOTE or SECONDARY DEVICE.
- Page 14 3) Press the P2 Button on the device again. The Motor controller will beep several times indicating that the secondary device has been cancelled. For queries or assistance with programming any of your G-Link devices please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am and 3:30pm P.S.T. Page 14 of 14...
Need help?
Do you have a question about the 98GCK-45DR and is the answer not in the manual?
Questions and answers