Girard Systems GC274C Installation And Instructions Manual
  1. Manuals
  2. Brands
  3. Girard Systems Manuals
  4. Control Unit
  5. GC274C
  6. Installation and instructions manual

Girard Systems GC274C Installation And Instructions Manual

Ac motor control module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AC MOTOR CONTROL MODULE
GC274C
INSTALLATION and PAIRING INSTRUCTIONS
REV.12302015
RV AWNING PRODUCTS
1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500
www.girardrv.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GC274C and is the answer not in the manual?

Questions and answers

Related Manuals for Girard Systems GC274C

Summary of Contents for Girard Systems GC274C

  • Page 1 AC MOTOR CONTROL MODULE GC274C INSTALLATION and PAIRING INSTRUCTIONS REV.12302015 RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500 www.girardrv.com...
  • Page 2 Shore Power – if connected; Generator Power – if the generator is running; Inverter Power – batteries must be charged for inverter operation. Girard Systems awnings are supplied with an electric motor appropriate to the product. Page 2 of 11...

  • Page 3: Table Of Contents

    These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation.

  • Page 4: Product Description

    Left and Right buttons of the module simultaneously for least 6 seconds. The GC274C may be programmed with up to 20 compatible remote modules. If an additional module is programmed it will replace the most recently programmed module.

  • Page 5: Specification

    1. Install a UL approved 110VAC junction box in which to make the electrical connections. 2. Route the Awning’s Motor cable to this location and make the connections to the GC274C in accordance with NEC requirements. Mount the GC274C on the wall using the screws and tape provided. Page 5 of 11...

  • Page 6: Setup And Programming

    6 seconds. The Green LED will illuminate and then blink a few times. When the Green LED extinguishes, the operation is complete. To access the Program Mode of the GC274C Simply press and hold the middle and right buttons of the controller simultaneously for 10 seconds. The green LED will begin to flash.

  • Page 7: Programming To A Dry Contact Module

    5. Programming the GC274C to a Dry Contact Module GC1149A MODES OF OPERATION The GC1149A has 3 modes of operation; 1. Continuous Mode (Default) – A single press of a command button will allow the awning to fully extend or retract unless interrupted by the STOP button.

  • Page 8: Programming To An Anemometer

    Supply power to the GC274C and the GC116I(Leave them on if already on) c. Press the PROGRAM button on the GC274C (the Green LED will start to blink) d. Press the STOP button on the GC274C (The Green LED will remain illuminated) e.

  • Page 9: Programming To A Motion Sensor

    7. Programming the GC274C to a Motion Sensor (98GC779G) This procedure will require opening up the motion sensor module by following the directions below; a. Remove the 2 small cross head screws which secure the motion sensor to the mounting bracket.
  • Page 10 c. Remove the 4 cross head screws holding the module together. Remove the back plate and silicone insert. See Fig.3. Base plate Magnet Silicone Insert Fig.3 d. Turn the base plate over (Magnet down). Then place the motion sensor on top of it so that the magnet is aligned with the reed switch.
  • Page 11 Once programming is complete, reassemble the motion sensor module and mount on the awning lead rail. For queries or assistance with programming any of your G-Link devices please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am and 3:30pm P.S.T. Page 11 of 11...

Table of Contents