Promac MBS-910CS Operating Instructions Manual page 4

Install the machine so that there is sufficient
space for safe operation and workpiece
handling.
Keep work area well lighted.
The machine is designed to operate in closed
rooms and must be placed stable on firm and
levelled ground.
Make sure that the power cord does not
impede work and cause people to trip.
Keep the floor around the machine clean and
free of scrap material, oil and grease.
Stay alert!
Give your work undivided attention. Use
common sense.
Do not operate the machine when you are
tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication can
change your behaviour.
Keep children and visitors a safe distance
from the work area.
Never reach into the machine while it is
operating or running down.
Never leave a running machine unattended.
Before you leave the workplace switch off
the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire extinguisher
operation and place.
Do not use the machine in a dump
environment and do not expose it to rain.
Specifications regarding the maximum or
minimum size of the workpiece must be
observed.
Do not remove chips and workpiece parts
until the machine is at a complete standstill.
Never operate with the guards not in place –
serious risk of injury!
Connection and repair work on the electrical
installation may be carried out by a qualified
electrician only.
Have a damaged or worn cord replaced
immediately.
Make all machine adjustments or
maintenance with the machine unplugged
from the power source.
Remove defective saw blades immediately.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards may still
exist
The moving saw blade in the work area can
cause injury.
Broken saw blades can cause injuries.
Thrown cutting chips and noise can be health
hazards.
Be sure to wear personal protection gear
such as safety goggles and ear protection.
The use of incorrect mains supply or a
damaged power cord can lead to injuries
caused by electricity.
4. Machine specifications
4.1 Technical data
MBS-910CS:
Wheel diameter
Cutting capacity 90°
Cutting capacity 45°
140 x 140 mm
Cutting capacity 60°
Arm swivel range
Sawblade length
Blade width
Blade thickness
Cutting speeds 2
Coolant tank
Coolant pump
Overall(LxWxH) 1500x1100x1750mm
Weight
Mains 400V ~3/PE 50Hz
Output power 1,1 kW (1,5 HP)-S1
Reference current
Extension cord (H07RN-F):
Installation fuse protection
4.2 Noise emission
Acoustic pressure level (EN 11202):
Idling
Operating
The specified values are emission levels and
are not necessarily to be seen as safe
operating levels.
As workplace conditions vary, this
information is intended to allow the user to
make a better estimation of the hazards and
risks involved only.
4.3 Contents of delivery
Machine stand
Bimetal sawblade
Adjustable material stop
Hydraulic cylinder
Coolant facility
Assembly kit
Operating manual
Spare parts list
4
4.4 Machine description
A
B
E
295 mm
dia. 225mm
A....Power indicator light
200 x 200mm
240 x 160mm
B....ON-button
dia. 160mm
C.... STOP/ Emergency off-button
155 x 115mm
D....Low / High speed switch
dia. 90mm
E....ON/OFF switch
90 x 90 mm
0° - 60°
U....Auto/Manual switch
2455 mm
F....Feed control valve
27 mm
0,9 mm
G....Feed ON/OFF valve
35/ 70 m/min
8 litre
0,07 HP
220 kg
3.9 A
4x1,5mm²
16 A
75,2 dB (A)
MBS-910CS
86,2 dB (A)
K
J
I
0
H....Arm swivel lock
I.....Vise operating handwheel
U
Fig 1
L M
N
O
P
S
T
Fig 2
C
D
R
Q
H