Promac MBS-910CS Operating Instructions Manual page 3

GB - ENGLISH
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new Promac-machine. This manual has been prepared for the owner
and operators of a Promac MBS-910CS, metal band saw to promote safety during installation, operation and maintenance procedures. Please read and
undertand the information contained in these operating instructions and the accompanying documents. To obtain maximum life and efficiency from
your machine, and to use the machine safely, read this manual thoroughly and follow instructions carefully.
...Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
Authorized use
General safety notes
Remaining hazards
4. Machine specifications
Technical data
Noise emission
Contents of delivery
Machine description
5. Transport and start up
Transport and installation
Assembly
Mains connection
Starting operation
6. Machine operation
7. Setup and adjustments
Changing blade speed
Changing sawblade
Blade guides adjustment
Guide bearing adjustment
Blade tracking adjustment
Feed speed adjustment
Vise adjustment
Saw arm adjustment
8. Maintenance and inspection
9. Troubleshooting
10. Environmental protection
11. Available accessories
1. Declaration of conformity
On our own responsibility we hereby declare
that this product complies with the
regulations* listed on page 2. Designed in
consideration with the standards**.
2. Warranty
JPW (Tool) AG guarantees that the supplied
product(s) is/are free from material defects
and manufacturing faults.
This warranty does not cover any defects
which are caused, either directly or
indirectly, by incorrect use, carelessness,
damage due to accidents, repairs or
inadequate maintenance or cleaning as well
as normal wear and tear.
Further details on warranty (e.g. warranty
period) can be found in the General Terms
and Conditions (GTC) that are an integral
part of the contract.
These GTC may be viewed on the website of
your dealer or sent to you upon request.
JPW (Tool) AG reserves the right to make
changes to the product and accessories at
any time.
3. Safety
3.1 Authorized use
This machine is designed for sawing
machinable metal and plastic materials only.
Machining of other materials is not
permitted and may be carried out in specific
cases only after consulting with the
manufacturer.
Never cut magnesium-
high danger to fire!
The proper use also includes compliance
with the operating and maintenance
instructions given in this manual.
The machine must be operated only by
persons familiar with its operation and
maintenance and who are familiar with its
hazards.
The required minimum age must be
observed
The machine must only be used in a
technically perfect condition.
When working on the machine, all safety
mechanisms and covers must be mounted.
In addition to the safety requirements
contained in these operating instructions and
your country's applicable regulations, you
should observe the generally recognized
technical rules concerning the operation of
metalworking machines.
3
Any other use exceeds authorization.
In the event of unauthorized use of the
machine, the manufacturer renounces all
liability and the responsibility is transferred
exclusively to the operator.
3.2 General safety notes
Metalworking machines can be dangerous if
not used properly. Therefore the appropriate
general technical rules as well as the
following notes must be observed.
Read and understand the entire instruction
manual before attempting assembly or
operation.
Keep this operating instruction close by the
machine, protected from dirt and humidity,
and pass it over to the new owner if you part
with the tool.
No changes to the machine may be made.
Daily inspect the function and existence of
the safety appliances before you start the
machine.
Do not attempt operation in this case,
protect the machine by unplugging the mains
cord.
Remove all loose clothing and confine long
hair.
Before operating the machine, remove tie,
rings, watches, other jewellery, and roll up
sleeves above the elbows.
Wear safety shoes; never wear leisure shoes
or sandals.
Always wear the approved working outfit
Do not wear gloves while operating this
machine.
For the safe handling of saw blades wear
work gloves.
Insure that the workpiece does not roll when
cutting round pieces.
Use suitable table extensions and supporting
aids for difficult to handle workpieces.
Always adjust the blade guide close to the
workpiece.
Remove cut and jammed workpieces only
when motor is turned off and the machine is
at a complete standstill.