Download Print this page

Advertisement

Quick Links

Xerox wc 5019 service manual pdf
WorkCentre 5021/5019 Service documentation 5021/5019 Toilets 702P00886 VISUAL DOCUMENTATION Original
edition 08/2012. Xerox service documentation is intended for use by certified and trained service personnel only.
bevoxuba Xerox makes no warranty or representation that future changes to this documentation will be announced or
anticipated.
Customer support for devices, modules, components or parts of such devices may affect Xerox's responsibility to repair
machine failures under the warranty offered by Xerox for such devices. You should read the applicable customer service
or third party service warranty terms and conditions. If Customer provides technical assistance with respect to such
equipment, modules, components or parts thereof, Customer releases Xerox from all liability for Customer's actions and
agrees to defend, defend and hold Xerox harmless from all claims of third parties , which may arise directly or indirectly
from claims arising directly or indirectly that may be asserted in connection with these services. Although Xerox has
made every effort to ensure that the Documentation is accurate, Xerox assumes no liability for any inaccuracies or
omissions. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors
will be corrected in future editions. yixomuluno Prepared by Creative and Technical Communications-North America
800 Phillips Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. All
rights reserved. Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other
countries. tinisimibawu Changes to this document are made periodically. Changes, technical inaccuracies and
typographical errors will be corrected in future editions. This warning may generate, use and radiate radio frequencies
and, if not installed and used in accordance with the instruction manual, may result inB'WORCENTER 5021/5019
Service Documentation WC 5021/5019 Service Documentation 702P00886, first edition 08.08.2012 *** Xerox private
data *** The entire service documentation is provided for informational purposes only. for informational purposes.
Xerox service documentation is intended for use only by certified service personnel who have been trained in this
product. fikocizuwefaso Xerox makes no warranty or guarantee that customers will notify or notify customers of
changes in this documentation in the future. Customer maintenance of devices, modules, components or parts thereof
may affect Xerox's liability for warranty services offered by Xerox for such devices.
Please note the corresponding customer warranty or service from a third party supplier. In the event of customer
service with respect to such devices, modules, components or parts thereof, the Xerox customer waives any liability for
the acts of the customer and agrees to defend and hold Xerox harmless from all allegations created directly or indirectly
claims allegations allegations of creations of creations directly or indirectly created allegations of claims of creations of
creations of creations directly or indirectly created allegations of claims of creations of creations of creations of
creations directly or indirectly created by third party. For such service. Although Xerox strives to ensure the accuracy
of the materials, Xerox is not responsible for any inaccuracies or omissions. Changes to this document are made
regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent publications. Created
by Creative and Technology Communications\XE2\X93 North America 800 Phillips Road, Building 218-01A Webster,
New York 14580 ISO27001 CERTIFIED\XC2\XAA920 Xerox. All rights reserved. Xerox\xc2\xae and Xerox and
Design\xc2\xae are trademarks of the Xerox Corporation in the United States and/or other countries. Changes to this
document are made regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent
publications. lazotegudugiru Caution: This device generates and uses high frequency energy and can radiate
itWorkCentre 5021/5019 0-1 0.1 Meet this service manual................................................... . ... soyisafine ....
.................................... 0-3 0.2 How use service instructions ....
....
Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be
corrected in future editions. himurizi Prepared by Creative and Technical Communications-North America 800 Phillips
Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. All rights
reserved. leyihovilali Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or
other countries. Changes to this document are made periodically.

Advertisement

loading

Summary of Contents for Xerox wc 5019

  • Page 1 Xerox wc 5019 service manual pdf WorkCentre 5021/5019 Service documentation 5021/5019 Toilets 702P00886 VISUAL DOCUMENTATION Original edition 08/2012. Xerox service documentation is intended for use by certified and trained service personnel only. bevoxuba Xerox makes no warranty or representation that future changes to this documentation will be announced or anticipated. Customer support for devices, modules, components or parts of such devices may affect Xerox's responsibility to repair machine failures under the warranty offered by Xerox for such devices. You should read the applicable customer service or third party service warranty terms and conditions. If Customer provides technical assistance with respect to such equipment, modules, components or parts thereof, Customer releases Xerox from all liability for Customer's actions and agrees to defend, defend and hold Xerox harmless from all claims of third parties , which may arise directly or indirectly from claims arising directly or indirectly that may be asserted in connection with these services. Although Xerox has made every effort to ensure that the Documentation is accurate, Xerox assumes no liability for any inaccuracies or omissions. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. yixomuluno Prepared by Creative and Technical Communications-North America 800 Phillips Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. All rights reserved. Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries. tinisimibawu Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. This warning may generate, use and radiate radio frequencies and, if not installed and used in accordance with the instruction manual, may result inB'WORCENTER 5021/5019 Service Documentation WC 5021/5019 Service Documentation 702P00886, first edition 08.08.2012 *** Xerox private data *** The entire service documentation is provided for informational purposes only. for informational purposes. Xerox service documentation is intended for use only by certified service personnel who have been trained in this product. fikocizuwefaso Xerox makes no warranty or guarantee that customers will notify or notify customers of changes in this documentation in the future. Customer maintenance of devices, modules, components or parts thereof may affect Xerox's liability for warranty services offered by Xerox for such devices. Please note the corresponding customer warranty or service from a third party supplier. In the event of customer service with respect to such devices, modules, components or parts thereof, the Xerox customer waives any liability for the acts of the customer and agrees to defend and hold Xerox harmless from all allegations created directly or indirectly claims allegations allegations of creations of creations directly or indirectly created allegations of claims of creations of creations of creations directly or indirectly created allegations of claims of creations of creations of creations of creations directly or indirectly created by third party. For such service. Although Xerox strives to ensure the accuracy of the materials, Xerox is not responsible for any inaccuracies or omissions. Changes to this document are made regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent publications. Created by Creative and Technology Communications\XE2\X93 North America 800 Phillips Road, Building 218-01A Webster, New York 14580 ISO27001 CERTIFIED\XC2\XAA920 Xerox. All rights reserved. Xerox\xc2\xae and Xerox and Design\xc2\xae are trademarks of the Xerox Corporation in the United States and/or other countries. Changes to this document are made regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent publications. lazotegudugiru Caution: This device generates and uses high frequency energy and can radiate itWorkCentre 5021/5019 0-1 0.1 Meet this service manual............soyisafine ........0-3 0.2 How use service instructions ..
  • Page 2 If Customer provides technical assistance with respect to such equipment, modules, components or parts thereof, Customer releases Xerox from all liability for Customer's actions and agrees to defend, defend and hold Xerox harmless from all claims of third parties , which may arise directly or indirectly from claims arising directly or indirectly that may be asserted in connection with these services. Although Xerox has made every effort to ensure that the Documentation is accurate, Xerox assumes no liability for any inaccuracies or omissions. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. Prepared by Creative and Technical Communications-North America 800 Phillips Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. All rights reserved. Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. This warning may generate, use and radiate radio frequencies and, if not installed and used in accordance with the instruction manual, may result inB'WORCENTER 5021/5019 Service Documentation WC 5021/5019 Service Documentation 702P00886, first edition 08.08.2012 *** Xerox private data *** The entire service documentation is provided for informational purposes only. for informational purposes. Xerox service documentation is intended for use only by certified service personnel who have been trained in this product. Xerox makes no warranty or guarantee that customers will notify or notify customers of changes in this documentation in the future. Customer support for devices, modules, components or parts of such devices may affect Xerox's responsibility to repair machine failures under the warranty offered by Xerox for such devices. You should read the applicable customer service or third party service warranty terms and conditions. If Customer provides technical assistance with respect to such equipment, modules, components or parts thereof, Customer releases Xerox from all liability for Customer's actions and agrees to defend, defend and hold Xerox harmless from all claims of third parties , which may arise directly or indirectly from claims arising directly or indirectly that may be asserted in connection with these services. Although Xerox has made every effort to ensure that the Documentation is accurate, Xerox assumes no liability for any inaccuracies or omissions. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. Prepared by Creative and...
  • Page 3 Technical Communications-North America 800 Phillips Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. This warning may generate, use and radiate radio frequencies and, if not installed and used in accordance with the instruction manual, may result inB'WORCENTER 5021/5019 Service Documentation WC 5021/5019 Service Documentation 702P00886, first edition 08.08.2012 *** Xerox private data *** The entire service documentation is provided for informational purposes only. for informational purposes. Xerox service documentation is intended for use only by certified service personnel who have been trained in this product. Xerox makes no warranty or guarantee that customers will notify or notify customers of changes in this documentation in the future. Customer maintenance of devices, modules, components or parts thereof may affect Xerox's liability for warranty services offered by Xerox for such devices. Prepared by Creative and Technical Communications-North America 800 Phillips Road, Building 218-01a Webster, New York 14580 ISO9001 and ISO27001 © 2012 Xerox Corporation. All rights reserved. Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries. Changes to this document are made periodically. Changes, technical inaccuracies and typographical errors will be corrected in future editions. This warning may generate, use and radiate radio frequencies and, if not installed and used in accordance with the instruction manual, may result inB'WORCENTER 5021/5019 Service Documentation WC 5021/5019 Service Documentation 702P00886, first edition 08.08.2012 *** Xerox private data *** The entire service documentation is provided for informational purposes only. for informational purposes. Xerox service documentation is intended for use only by certified service personnel who have been trained in this product. Xerox makes no warranty or guarantee that customers will notify or notify customers of changes in this documentation in the future. Customer maintenance of devices, modules, components or parts thereof may affect Xerox's liability for warranty services offered by Xerox for such devices. Please note the corresponding customer warranty or service from a third party supplier. In the event of customer service with respect to such devices, modules, components or parts thereof, the Xerox customer waives any liability for the acts of the customer and agrees to defend and hold Xerox harmless from all allegations created directly or indirectly claims allegations allegations of creations of creations directly or indirectly created allegations of claims of creations of creations of creations directly or indirectly created allegations of claims of creations of creations of creations of creations directly or indirectly created by third party. For such service. Although Xerox strives to ensure the accuracy of the materials, Xerox is not responsible for any...
  • Page 4 Changes to this document are made regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent publications. Created by Creative and Technology Communications\XE2\X93 North America 800 Phillips Road, Building 218-01A Webster, New York 14580 ISO27001 CERTIFIED\XC2\XAA920 Xerox. All rights reserved. Xerox\xc2\xae and Xerox and Design\xc2\xae are trademarks of the Xerox Corporation in the United States and/or other countries. Changes to this document are made regularly. Changes, technical inaccuracies and typographical errors are corrected in subsequent publications. Caution: This device generates and uses high frequency energy and can radiate itWorkCentre 5021/5019 0-1 0.1 Meet this service manual....................0-3 0.2 How use service instructions ................0-3 0.3 Description of terminology and symbols ............0- 4 Original edition 08/20 2012 Introduction 5021 /5019 0- 1 0.1. Understanding service instructions 0.2 How to use service instructions. These instructions serve as standard service instructions for the WorkCentre 5021/5019. This tutorial describes standard operating procedures for standard maintenance procedures for this product. To get efficient and effective service during maintenance, please refer to Chapter 1 connecting to the service. For more information about options, see Options. 2.1. Contents of the Tutorial This tutorial is divided into 10 chapters, as described below. • Chapter 1 Service View This chapter describes the general operations and maintenance procedures for maintaining this product. • Chapter 2 Troubleshooting This chapter describes other troubleshooting problems than the image quality solution in this product. • Chapter 3 Solving Image Quality Problems This chapter describes the procedures for solving image quality problems in this product. • Chapter 4 Disassembly/Assembly and Adjustment This chapter describes the procedures for disassembling, assembling, adjusting and replacing this product. • Chapter 5 The parts list in this chapter contains information about replacement parts for this product. • Chapter 6 General Information This chapter contains the following information. 6.1 Specifications 6.2 Tools/Consumers/Auxiliary Materials 6.3 Service Data 6.4 Service Mode 6.6 KO List - Chapter 7 Wiring Data This chapter contains information about the list/location of wiring connectors, wiring and BSD data for this device. Area • Chapter 8. Other accessories (not yet released) • Chapter 9. Installing/Removing this0.1, 0.2 0-3 0.3 Description of terms and symbols in this guide describes the terms and symbols used in this guide. • The conditions and symbols used at the beginning of the text are determined as follows: “dangerous” implies an unavoidable dangerous situation such as death or serious injury unless the operators control the machine without the result of the declaration. The warning indicates a potentially dangerous situation such as death or serious injury if operators cannot properly modify the car without receiving the declaration. The goals of attention are used to describe the goals of adaptation and solutions to problems. ANSWER: The link should specify the link/assembly procedure. Adj: Displays the procedure for setting the task. PL: Provide a list of parts for information. This terminology refers to a potentially dangerous situation, such as injury or damage to property, when operators cannot properly handle equipment without warning. Instructions: It is used to warn about the procedure without the possibility of causing damage to the device or device. Table 1 Terminology -Terminology Description ASSY MEISS AUSBAG. The abbreviation of the TEC value, which is characteristic of the power consumption, means the standard energy consumption. Read as "text". Introduction 08/2012 First edition 0.2, 0.3 0-4 WorkCentre 5021/5019 1.1 before maintenance begins ............
  • Page 5 and the relative packaging material is reported to the Service Center. The methods for separating and treating the collected elements are in general technical information Available. 2-027 for all machines. • Never throw the drum into the fire. Always keep it away from free flames to avoid fires and fire. Always remove the drums after wearing them completely. Fill out the necessary elements for the recyclable parts and create a collection. 5. General preventive measuresOperator depending on the state of the machine. 2. Enter the bailout meter deduction. 3. Check all incorrect copies, then check the device. 4. Check the service log. 1.2. 2. Do the appropriate FIP to eliminate level 2 [2. Troubleshooting section]. 3. If there is no suitable item, remove the problem according to [7. BSD chapter]. 4. Check the quality of the copies. Make numerous copies using the test card (499T 00247), then check the quality of the copy to determine if there are any problems. 5. Print [Error History Report] and check [System Failure History] and [Paper Tension History] to learn about the machine status. (1) Enter system administrator mode. I. Press and hold the [Application/Output] button for 4 seconds or more until this screen appears. Figure 1 J0LJ41896 II. Using the keypad, enter the passcode [11111] * 1 (5 digits '1') and press the [Start] key. Note: *1: Default III. The screen number is displayed. Figure 2 J0LJ41897 (2) Put the sheet A4 SEF, A4 LEF, letter SEF or Lef. (3) Enter "202" in the program box and press the [Start] key. (4) Enter "4" [History Report Error] and press the [Start] key. (5) After printing, press the [sign/display] button to enter Manager mode. Note: If you are exchanging customer data, ask the customer for permission before exchanging. 6. Improve all secondary issues. 7. Perform finishing service. 1.2.3. If you need SM, create the following: 1. Check the quality of the copy. Make numerous copies using the test card (499T 00247), then check the quality of the copy to determine if there are any problems. 2. Print [Error History Report] and check [System Fault History] and [Paper Tension History] to learn more about the machine status. "How to print [um]Copy samples with a service register. 1.3. Detailed services cause content 1.3.1. First action 1. Ask the camera machine conditions. • What frequency and where the latest paper jams are copies. 2. Pick up the copy knife. 3. Check all copies of the error and inspect the car. 4. Check the print samples from the previous service connection and in the service register. 1.3.2. Recovering the problem 1. Check the status of the problem and differentiate between level 1 [2. solving the problems of the department]. 2. Follow FIP Level 2 Issues [2. Disturbances in the section]. 3. In the absence of applicable elements, solving problems in the light [7. BSD department]. 1.3.3. Quality check copy 1. Test scheme (499T 00247), run different copies and then check the quality of the copy. 1.3. 1. Follow the final test list to complete the required finishing items. 2. Check parts that require periodic cleaning/replacement (consumable materials, parts) and provide a list of finishing controls, a period of periodicity/use of spare parts, and clean and tidy. After switching, make sure to insert EC mode and use [HFSI Reading/Cleaning/Cleaning] to withdraw the correct money. The 2012 service connection procedure clean, replace or clean food if necessary. A: Always clean and try. *: Always perform backup service in a specific area. Table 1. Time Services Maintenance Items 1.1 Previous Services C Control Machine and Pathological Check (Check Machine Noise) 1.2 Control Quality Test Scheme). 2 clean T.it was dry. • Clean the DADF platinum glass optical cleaning cloth. 5 Safety or ¢ Make sure the power cover is connected correctly. • Make sure that the power cables have not been lost and that no thread is detected. • Make sure that insufficient extension length is not used, or the power cord does not meet specifications such as standard multiple socket. ¢ Make sure the outlet is no longer plugged in. 6.1. Post Assistant Control C ¢ Using the Test (Copy Quality Control) (499T 00247), make a few pages of copy and then check whether the quality meets the specification. 6.2 Changes after maintenance C • Check for paper feeding and abnormal noises. (Check the operation of the machine) 6.3. (Check the meter) 1.5 List of periodic spare parts/consumable items during maintenance, check the number of copies and remain powered by materials and parts that require periodic cleaning/replacement.
  • Page 6 ..2-15 005-196 there is no size without size mixed size ..............2-15 005-197 Combination size ......................2-15 005-198/ 199 is too much layer, Jam/ size is too large............ 2- 15 005-210 DADF download the file ................. 2-15 005-275 / 280 Dadf Ram Faw/ Dadf Eeprom FAW ............... 2-16 005-500 DADF error when loading Flash ..................2-16 005 -907/908/913 DADF sensor to the region/Dadf Regi/Static Static Sensor Static Sensor 2-16 005-940 Naorian DADF failures..................2-16 005-948 SS in the inconsistent size for the size mixture..............2-16 circle 10 010-311 centrum fuse Team is completed full ........Download the Flash program ............2-19 016-570. The USB host's response to the parsing task is unresponsiveness ..........2-19 016-571. The USB host's response to printing........... 2-19 016-742/ 744 Download file/ file download. Checksum Error ........ 2 -19 016-749/ 799 HBPL or XPJL Syntax Error/ DI INSTRUCTIONS INSTRUCTION........2-20 016-759 Complete copies....................... 2-20 Marker Code Detection Error 016-776 ..............2-20 Circumference 23 023 -600 main fault (control panel 'user interface ) ..................2-21 Circumference 24 024- 910 /911/ 915 1 1/2 bin bac 2/MSI card mismatch........2-23 024-950 /951 /954 BAC 1 1 /BAC 2 /MSI no paper ........... 2-23 024-958/959/960 MSI/BAC 1/2 BAC 2 Unbraked paper format ........2-23 024 -965 ap ng or chosen .................. Circulation 2-23 41 041-210/ 211 ERROR STM NVM OUNTROD/ STM NVM O/ Z ........... Circuit 2-25 42 042 -325/614 Main Engine Warning/Main Engine Error Commercial Rotation ......diagram 2-27 45 045-310 Image preparation error ................2 -29 045-313 IoT Logic Error ........................2-29 circumference 61 061-321 ROS engine failure......................2-31 061-325 The sauce is not afraid ...........2-33 062-386 FULIZATION AOC ...................... 2-34 062-389 Awaria Przejazdu Wózka (Strona Końcowa Skanowania) ............2-34 062-396 CCD connection error ................2-34 Chain 71 071-105 Area Jam Sensor (Power Supply 1) ................
  • Page 7 about the failure of the FIP sensor ......................2-59 2.2.4.2 ....................................................2-59 2.2.4.3 The switch (normal/open) FIP failure......................2- 60 2.2.4.4 magnet/communication is not fragments of FIP energy ............2-60 2.2.4.5. Magnet/clutch on the left FIP FIP ............................................2-61 2.2.4.6 the engine does not turn into FIP ..............2-61 2.2.4.7........2-62 2.2.4.8. Map/freestalfmagnet without FIP power supply ........ 2 -62 2.Sensor errors ...................... . 2 - 45 chain 93 093-312 rotation of the toner power engine ............2-47 093-400 toner almost exhausted ..................2-47 093-406 Toner almost exhausted ................2-47 093-912 Empty toner ........................2-47 093-956 Installation of the new Cru cylinder Faiche ............. 2-47 093-959 The installation error of the new Cru cylinder exceeds the thresholds ............2-47 chain 95 095-910 without a drum cartridge ......................2- 49 string 116 116-321 controller logical errors..............................2-51 116 -323 Data controller error -nvm ................ 2-51 116-334 Speed NVM data ..............................2-51 116-377 IIT escape time ................2-51 116 -747 Unconidal lateral connection ..............2- 51 Corda 117 RAPISEED STATE INDICATOR 08/2012 First edition 2-2 WorkCentre 5021/5019 2.1.1 As a resolution of level 1 problems: • The correction of level 1 errors (1 level 1 FIP ) is the first step in the diagnosis of a problem. A level 1 FIP asks if there is an error code and other symptoms of the problem and forwards them to the resolution of level 2 or BSD problems to solve the problem. Reading of level 2 errors: • The level of correction of level 2 errors is a diagnostic procedureAnd do the procedure correctly. Sometimes, if there are two or more causes, they cannot be immediately identified and the FIP itself must be repeated. In this case, use another solution provided in the same FIP process. • For problems related to the supply voltage, such as the machine not being listed, see the "Other FIP Errors" section for additional troubleshooting. • In some cases, a procedure for checking general electrical parts (motor, solenoid/connector, switch, sensor, etc.) can be displayed for troubleshooting and troubleshooting. In these cases, please refer to the general FIP section for troubleshooting. 2.1.2 How to enable/disable error code display. If there is a problem with the device on the user interface screen, an error or error code (circuit link) will be displayed. When an error code appears, the following operation can be performed to switch the view to the circuit level corresponding to that error code. To fix, check the circuit connector number and run the appropriate FIP. How to proceed to connect the circuit 1. If there is a problem, the error code will flash. Figure 1 J0LJ21201201 2.
  • Page 8 get a document from the user and contact support for help. 003-942 Untrusted BSD-ON document format: - Untrusted document format detected. Cause/Action 1. Click [Stop] in the user interface area. 2. Check the document size group setting. 3. Check the document size. 4. If the document format is supported, DADF may not work properly. To check the DADF, see this FIP. • 005-196 (Stuck due to SS size mismatch in unmixed format) • 005-948 (Stuck due to SS size mismatch blocking insoluble size) Cause/Action Click [Stop] on the UI panel and change the settings. 003-972 EPC memory full BSD-ON: - EPC memory full during copy. Cause/Action Print all images that have been successfully scanned by the DADF so far, then copy again to find the documents (images) that failed to be scanned. 003-973 NG Autorotate outside BSD-ON range: - The following conditions were met during copying. • Rotation required. • At document reduction/enlargement ratio X, the resulting image is larger than 297 mm. Cause/Action Click the [Stop] button on the user interface and change the reduction/enlargement ratio. First Edition 08/2012 RAP Status Screen 003- 500/795, 003-951 WorkCentre 5021/5019 2-9 RAP Status Screen 08/2012 Initial Edition 003-500/795, 002-951 WorkCentreeRAP 08/2012 First edition 004-345 2-12 Worcentre 5021/5019 005-122 Dadf Simplex Senzer Initial Record/1. Page BSD-on: CH5.4 • When the first sheet of paper (DADF) begins, serve the engine running (clockwise) in the initial registration sensor in one-sided and double-sided mode, which does not turn at the specified time. • Starting with the second sheet pre -feed (the Dadf motor is on (clockwise)) in a double mode, the preliminary registration sensor does not turn on the specified time. 005-125/145 DADF recording sensor locked/recording DADF sensor is disabled. Reverse locked BSD-on: CH5.5, CH5.4 [Dadf recording sensor) When the DADF pre-recording sensor was turned off during the scan, the Dadf recording sensor did not turn off within the specified time. Cause/Action Check the following: • Transport error caused by foreign bodies on the document track. • The surface of the feed cylinder and pressure cylinder is free of foreign bodies. • Check the surface wear and pressure roller surface. • Initial PADF Registration Sensor (Check Input [005-206]) to not work incorrectly. (PL 56.14) • Dadf Food Clutch escapes (output management [005-062]). (PL 56.7) • Dadf motor (check output [005-008]) to detect unusual operation. (PL 56.6) • Wear and damage wheel. If you have no problem, replace the DADF card. (PL 56.2) 005-123 Simplex/Side 1 blocked Dadf recording sensor. BSD-on: CH5.5, CH5.4 Preliminary recording sensor Dadf will not switch to preliminary recording sensor at the specified time. [The Dadf Recording Sensor stuck in the reverse] after the reverse mode was turned off in the reverse mode, the DadF recording sensor did not turn off within the specified time. Cause/Action Check the following: • Transport error caused by foreign bodies on the document track. • There are no foreign bodies on the surface of the registration cylinder, output cylinder and output cylinder. • The surface of the registration cylinder, output cylinder and output cylinder is worn. • DADF recording sensor (select input [005-110]) malfunction. (PL 56.14) • DADF Preliminary Registration Sensor (Entrance Management [005-206])Pre- cooking sensor (input test [005-206]) in operational errors. (PL 56.14) ¢ DADF T/A Sooling (Initial Test [005-098]) in Corporate Bankruptcy. (PL 56.7) â € â° DADF Engine Power Piews Supply (Output Test [005-008]) for operation failure. (PL 56.6) MBERS Tax Union. If no problem occurs, replace the DADF conductor plate. (PL 56.2) 005-131/ 132 DADF return sensor for connection with DADF return sensor for BSD-ON connection: CH5.5, CH5.4. Rear [Rear DADF Sensor] After the Regue DADF sensor was turned on during the scanning process, the rear father sensor did not load at the specified hour. Checking cause/solutions: Mbers transports errors due to foreign bodies in the document path. Original edition 08/2012 View state rap 005-122, 005-125/145 WorkCentre 5021/5019 2-13 Be sure to check for wear. • DADF return sensor (entry test [005-211]) for fault. (PL 56.10) â ALC DADF sensor (input test [005-110]) for operational errors. (PL 56.14) ††(PL 56.6) MBERS Tax Union. If no problem occurs, replace the DADF conductor plate. ) Time cannot be deactivated.
  • Page 9 BSD-ON Cover: CH5.1 CH5.1 The DADF switch cover was opened during DADF. • TAK-SENSOR (input test [005-211]) (PL 56.10) 3. If no problem, replace the Dadf PWB. (PL 56.2) 005-940 DADF not original BSD-ON: CH5.1 named that document was sent by document. Restart the document / company. Reason / Operation 1. Check the DADF power supply. 2. Check the DADF power lock (input inspection [005-212]). (PL 56.6) 3. If there is no problem, replace the DADF card. (PL 56.2) 005-500 BSD-ON MAEAL Flash-Memory Recording Error: CH3.1 DAFD did not flash during load. Reason / Operation 1. Switch off and simple diet. 2. If the problem persists, replace the following information one at a time: -Dadf (PL 56.2) Board-Ess / MCU (PL 18.1) 005-948 Non-compliance SS SS flakes, no mixed BSD-on-on-on-on : Area CH5 4 4, CCH5.22.2 "no shuffle" mode, it was detected that the smaller document from the DADF was moved towards the slow scan (SS). Reason / Action 1. Check the size of the user submitted by the user. 2. If the error is not corrected, check: (PL 56.14) • Document 1/2. Tablet size sensor (record test [005-221/222]) working error. (PL 56.11) 3. If there is no problem, replace the DADF card. (PL 56.2) 005-907 / 908/913 Dadf Prerere Registration Sensor / Dadf / Sagnur Dadf. Use the closed classification cover or open the father sensor. Close to. Reason / Operation 1. Check the presence of the corresponding sensor, the powerful return material mechanism, sensor contamination, etc. 2. Check the corresponding sensor for the presence of failed work. -Takif-setting sensor (input test [005-206]) (PL 56.14) -DADF recording sensor (input test [005-110]) (PL 56.14) RAP 08/2014 DisplayMeasure the resistance between the spindle 1 ESS/MCU PWB J403 and contact 2 J403. Resistance is endless? Replace the ESS/MCU board. (PL 18.1) Check this wiring for the presence of cliffs of the chain and bad contacts. • Between the ESS/MCU PWB J403-1 and the heated central thermistor of the P600-4 shaft. • between the ESS/MCU PWB J403-2 board and the heated termistor of the central shaft P600-3. Replace the heat -fastening unit. (PL 7.1) 010-312 BSD-on a malfunction of the rear thermistor of the heat-fastening node: CH10.2 Discard circuit (AD STS value equivalent to the open circuit of the rear thermistor of the roller). 010-320 BSD-on Back: CH10.2, CH10.1 found a malfunction due to high temperature in the central thermistor (245 degrees C or higher) or the rear thermistor (270 degrees C or higher). Note. To eliminate this malfunction, first eliminate the cause, and then set the value of NVM [744-040] (overheating error) to “0”, and then reduce the feed. The relationship between the displayed value and the termistor, which found a high temperature error, is as follows: • 0: normal • 1: the error of the central thermistor, the high temperature of the thermistor. Fouzer shaft • 2: The error of the termistor of the high temperature from the back of the FUUZER VAL CARE/ACTIVE/ACTION check the following points: ¢ Central or rear thermistor for the presence of falling parts, dirt on the sensor and foreign objects that block the sensor. ¢ A heated roller for the release and gluing of paper. • Heating of the clip centering zone (analog monitor [010-050]) due to the malfunction. • Heating of the rear thermistor (analog monitor [010-051]) due to the malfunction. • Heating the rod due to the malfunction. If there are no problems, replace the following first part: • Fuse block (PL 7.1) ¢ LVP (PL 18.1) • PWB ESS/MCU (PL 18.1) procedure. Cross the power source and disconnect the P/J600 heating roller heater connector. Measure the resistance between the roll of the termistor of the rear thermistor J600 PIN-3 and J600 PIN-4. Resistance is endless? Yes, re -connect the P/J600 connector and measure the resistance.On the. • When the hold temperature is turned on, it does not reach the value within the specified time. Cause/Action Check the following items: • Heating element is not working properly. • Communication between LVP command J511 and P10 in case of interruption in circuits and poor contact. • Central thermistor in case of falling parts, dirty sensors and foreign bodies blocking the sensor. • Heating of the cylinder for folded and glued paper. First publication 8/2012 Status status indicator 010-311, 010-320 WorkingCentre 5021/5019 2-17. If no problems are found, replace the following parts in order: • Fixer (PL 7.1) • LVP (PL 18.1) • / MCU (PL 18.1) 010-379 Fix command return timing failed. No readiness. BSD-ON: CH10.2, CH10.1. The time required to restore the high temperature readiness status has exceeded the specified time. Time. Cause/Action 1. Turn off and on the device. 2. Turn off the power source and check the following items: • The locking unit is not installed correctly. • Communication between...
  • Page 10 the first time [045-310]. NOTE. In the case of continuous printing, this error occurred only after successful written paper, immediately transmitting the paper on which the corresponding image should be printed. Reason / action 1. Conclusion 2. If the problem is repeated, determine whether it is caused by copying or printing of documents, and apply for help to the support service. The status indicator Raps 08/2012 First edition 016-749/799, 016-776 2-20 Workcentre 5021/5019 023-600 Error storage (User interface) included: CH2.1, is supported for 1 minute or more. Reason / action make sure that any user interface key is pressed and stored. IntroductionRole and pressure rollers of appropriate foreign material. âszugwalzen surface, t/a roll 2 (subject 2), reg. Check the role and stress of the relevant tablet. 'Reggs sensor (entrance test [071-105]) due to malfunction. (PL 15.1) 'Regular connector (output test [071-001]) due to malfunction. (PL 15.1) 'MSI Feed Selection (Exit Testing) [072- 006]) due to malfunction. (MSI) (pl 13.3) "BTR for contamination, wear and transport loss due to wear and loss." "Check drive gear wear and damage. The use of paper does not match the specifications. If no problems are detected, replace the ESS/MCU PWB module. (PL 18.1) ESS/MCU PWB (FACH 1/MSI) (PL 18.1) 'STM PWB (Topic 2 ) (Pl 10.6) 024-958/959/960 mSI/FACH 2 POPER Format BSD-on-ENDERGE:-When making print order, selected entity paper settings different from the paper format specified in the command/measure to change the paper settings in the selected object. 024 -965 APS NG Selected with BSD -EI: -Copy sequence, print order and reference order with APS settings, paper size and paper leveling (SEF/LEF) different from settings in Chapter 1 and topic 2. section on appropriate settings. 024-950/951/954 1. Topic/Subject 2/msi from paper BSD-EI: CH7.2, CH7.3, CH7.4 was recognized one of the following events: "The appropriate topic has no longer been sheet of paper. . (If the Function 1 and 2 of the items 1 and 2 are disabled) • Although the document is recognized in the subject, no other subject document is attached. (If the APS function 1 and 2 is enabled) Reason/Solution 1. Put the paper in the relevant slot. ) appropriate division mechanism. "Violation and foreign body.NVM-R/W BSD-ON Error: CH3.2 [STM NVM not working] STM NVM is not working properly. [STM NVM Read/Write Error] Unable to perform STM NVM Read/Write. Cause/Measurement 1. Turn off the device and update. 2. If the problem persists, replace the STM board. (PL 10.6) First Edition 08/2012 Status Indicator Raps 041-210/211 WorkCentre 5021/5019 2-25 Raps Status Indicator Raps 20/08/2012/Main Motor Warning BSD-ON: CH4.1 [Main Gear Motor Error] Motor Rotation was detected as an error. When the motor drive bridge signal (main actuator motor failure) has been observed within the specified time interval after the specified time has passed since the main drive motor has failed five times in a row. [WARNING MOTOR SWITCH] An error was detected while the main drive motor was rotating. When the motor drive bridge signal (main actuator failure) was observed some time after the main actuator actuation, the failure was detected twice in a row. Procedure: Enter CE mode and enable test output [042-001] (main drive motor). Does the main engine rotate? Y n Check the main drive motor power supply (+24V DC, +5V DC). Is the main power source for the drive a conventional power supply? Y n Check the main drive motor power supply. Turn off the power and check: • The connection between the main drive motor J202 and the ESS/MCU controller board J403 is not open, has a short circuit and poor contact. • gearbox on a used, damaged and stored unit. • main charging engine. If the problem is not found, replace the following parts one by one: â ¢ Main Drive Motor (PL 3.1) â ¢ Ess/MCU Wiring Board (PL 18.1) Press [stop] and turn off the power. Check the connection between main drive motor J202-8 and ESS/MCU J403-5 for stop and short circuitAccording to the restoration company. Cause/Action 1. Check the incorrect connection of the USB cable (local). 2. If no problem is found, replace the ESS/MCU PWB. (PL 18.1) 045-313 BSD-ON IoT Logic Error: - CASE IoT software error found. Cause/Action 1. Turn the unit on and off. 2. Correct and stable online software version. 3. If the problem persists, replace the ESS/MCU PCB. ) BSD Error ROS - MOTOR -ON: CH6.4 The ROS motor speed did not reach the standard range within the specified time (5 s) according to the ROS motor. 061-325 No SOS Fail BSD-ON: CH6.4 After detecting Ross motor ready (stable rotation) the SOS range was found 5 times consecutively compared to the reference value. Cause/Action Cause/Action 1. Stop the utility a. 2.
  • Page 11 BSD-On: CH8.3, CH8.2 During the tension of the tablet paper 2 -On: CH7.1 Abnormal spit value of the ' Paper format switch 2. BAG 2. Control / Action Check the following elements: (PL 15.1) • STM Returns the engine (output test [072- 004]) for bankruptcy. (PL 10.6) • STM removes the rolls (output test [072-003]) for the bankruptcy of the company. (PL 10.6) • T / A 2 roll, premium power and rolls for transport error due to contamination, wear and deterioration. • Wear and damage to the equipment. Research on paper transport due to foreign substances on the way of the map. • Use a special card. Cause / action Check the following elements: ¢ Interrupted connection and damage at the bottom of the tablet and in the unit at the rear of the company's failure on paper 2 (analog monitor [072-050], [072-105]) for operation. (PL 10.1) • Billing costs of the dating card - a magazine for the existence of other objects such as paper. If there is no problem, replace PWB STM. (PL 10.6) If the problem is not detected, replace the following parts in order: 072-215 MCU-STM communication error. : Between ESS / MCU PWB and STM PWB, a CH3.2 communication error has been detected. Reason / ActionAdhesion. Check Cause/Action Check: • failure of REGI sensor (input control [071-105]). (PL 15.1)-Main drive motor (output control [042-001]) for operation. (PL 3.1) • MUSI source for MSI (output control [072-006]) operation. (PL 13.3) A - MSI Current Rolls and Bankruptcy, MSI wear due to deterioration. • Fertility and damage direction tool. • paper transport due to foreign matter on the paper. • Use of paper. In case of problems, replace the PWB in the ESS/MCU. ; All rights reserved. Xerox and Xerox and Design are trademarks of Xerox Corporation in the United States and/or other countries. Microsoft, Windows, Windows Server, Windows XP, Windows Vista, and Windows 7 are trademarks or registered trademarks of Microsoft. Dual document feeder (optional) ..3-5 Workcentre 5019/5021 ... 4 page Fermo with copier ..5-8 Workcentre 5019/5021 . .. P. Checking the Total Number of Copied Prints ..9-4 WorkCentre 5019/5021 ... p. Notes and Limitations on Using the Scan Feature ..12 -9 WorkCentre 5019/5021 ... Preface Thank you for choosing the 5019/5021 ('Machine' below) WorkCentre. This manual describes how to use the machine and the precautions that should be observed during operation. To remove the top from the car and use it effectively, be sure to read this manual before use. Help describes functions and print operations. Additional component guidelines are available for the components of this product. Additional components are delivered using an installation management guide that contains product configuration and other information. WorkCentre 5019/5021Machinery. Workcenter Power Directorates 5019/5021 User manual ... Please note that non - authorized changes, including adding new functions or a connection to external devices, may not be guaranteed by the product. The local representative of Xerox will be made available to you. Follow all warning instructions marked on this product. To display ... If the power cables are damaged or insulated, ask the replacement of the local Xerox representative. Do not use damaged or non -Iinsulated cables to prevent the risk of an electrical shock and fire. Page 13 Place the product in a well -ventilated place. Don't worry about the product ventilation holes. Keep the minimal place below for ventilation and access to the mains plug. If you notice a abnormal state, separate the product. With automatic power supply/retro 1100.9 325.9 (unit: mm) WARNING: WORKCENTRE 5019/5021 User manual ... This product is equipped with a safety function that prevents access to danger areas. The areas are isolated by shields or defenders who require the removal of tools. To avoid the electros and injury, never remove these covers...
  • Page 12 This list is not exhaustive and we do not guarantee its completeness or accuracy. If in doubt, contact your attorney. "Workcentre 5019/5021 1-15 user Operation ... page 22 Before using the machine 1-16 WorkCentre 5019/5021, you can scan documents on the pre-visit screen by checking digitization. For more information, read the scan data using 6-6 computer application. P Connect the USB cable to the USB 1.1 / 2.0 interface Connect the other volume of the USB cable to the computer Press the power switch to the position to activate the power supply WorkCentre 5019/5021 User Management ... The CD contains this print driver. Print Driver Description Name "Xerox Workcentre XXXX" Run the installation, click on the driver Click on the main menu of the drivers CD. Standard print driver. The data generated by the application software is converted into images before being sent to the printer. CD (HTML) documentation is on the CD. Deleting other software To delete other software installed from the driver CD, see the README file. READM files can be displayed on the Product Information CD (HTML). WorkCentre 5019/5021 User Manual ... This section refers to the C name of each computer.User manual ... Do not leave the car overturned. Push the car in the assembly position and turn this regulator clockwise until it touches the floor. USB 1.1 / 2.0 Connect the 1.1 / 2.0 USB cable. Connector (Type B) User Guide Workcentre 5019/5021 ... The product review contains a toner in the description of the component toner (dust is used to create the image). The drum cassette has a photo company. Units that connects paper to paper. Do not touch this unit because it is extremely hot. Workcentre 5019/5021 User Manager ... The Stropper document protects from the sewers. The output output is available here. Narrow glass belt scanning documents. Note in this guide, the supply of the automatic duplex document is called "SMKER Document". Workcentre 5019/5021 user manager ... When the machine is heated, the machine status scheme is displayed as indicated in the photo. There is no machine during heating. • Make sure the power cable is properly connected to the machine and the wall socket. Workcentre 5019/5021 User Manager ... before turning power, make sure that the machine has completed all copying or printing activities. So make sure the data indicator is not enlightened. Press the power switch in the off position to deactivate the power supply. Workcentre 5019/5021 User manager ... The external energy mode is defined for 1 minute. And sleep up to 1 minute. Factory during shipment. If the machine remains inactive for 1 minute, go into low power mode, then sleep if it does not work for the next minute. Workcentre 5019/5021 User Manager ... Enter the system administration method from the computer - Press any configuration panel button - Remove or place a tray - Opening or closing the cover or the Opening, opening or opening or opening or opening of Workcentre 5019/5021 Manual cover ... Log / Disable this button to access or leave the system administration method. Access / exit the buttonNot available to some models. If you add many options, you can use them. For more information, please contact our Customer Service Center. 3-12 Workcentre 5019/5021 user guide ... Check the size and orientation of the scanning set using the original size button when using the display glass. If a document has a document for sending documents, automatic detection is automatically installed and a car icon is displayed. Workcentre 5019/5021 3-13 User guide ... 36 and performs an appropriate procedure to remove paper or a fierce document. This error lights up when an error occurs, e.g. a problem with a tank, a contribution containing a ton of ink or an exhausted accumulator insert. 3-14 Workcentre 5019/5021 user manual ... Page 41 When many/documents appear or you open any cover, the notification area flashes, as shown below. The front cover of the left cover is 2 short parts B, 1 b, cover the manual tray. Password scan. Log in to the system in account mode. When the device is in the account mode, _ _ _ _ â â â â â â â â â â â â â `â` â "â" â "â" â "â" 3-16 workcentre 5019/5021 User management ... page 43 for Z Safety reasons when placing each password number on the display instead of the actually introduced number appears a dill. CLOSE START button to confirm the entered password. Start Workcentre 5019/5021 3-17 User Guide ... to enter again create the "entire/exit...
  • Page 13 Original: Photo and Text (Do not change) Copy of personality certificates, you can copy both sides of the identity certificate (Name map , a card of an employee, etc.) on one side of the card. Workcentre 5019/5021 5-15 User Management ... 80. P. Carefully place the identity certificate down from the upper left angle of the glass, then close the cover for documents. If you place a personality certificate too close to the exhibiting glass, copying on the edge of the identity certificate may be impossible. 5-16 WorkCentre 5019/5021 ... 81 user manual. Table of the device status: the tray indicator lights up in the selected tray, and the size of the paper is displayed on the paper orientation. Click the Start button. After the end of one page, the Start button will start flashing. Click the WorkCentre 5019/5021 5-17 button ... if you want to copy the merger 1-2 or the side of 2-1 for the binding of the short edge, change the tuning of the binding edge and load the document in the album orientation. Copying on a short edge is not properly performed if a book orientation is selected for a document or paper or a “leaf” function is used. 5-18 WorkCentre 5019/5021 User Manual ... The page setting on one side automatically sets a decrease/increase setting. The scaling ratio is automatically regulated in the range from 25% to 400%. Press the pages on the side button to select the desired copy method. Workcentre 5019/5021 5-19 Side Pages of the Workcentre 5019/5021 5-19 Manual ... If this function is turned on, the background noise of the document is removed during copying. If this function is disabled, the background noise is not removed. You can configureThe procedure varies according to the account mode used. For more information, see Account mode on page 3-16. 5-22 Workscentre user guide 5019/5021 ... Related documents such as the book Note Some models do not have a document power supply. An optional part is required. Contact your local xerox representative. Supported documents documents in documents Documents can insert standard documents. 88 When loading a document in the documents documents, follow the following procedure. Single or multiple sheets can be inserted. Remove any clamps or table terminals before loading a document in the document power supply. Guide to the WorkScentre user 5019/5021 ... Page 89 The document indicator turns on when the document is inserted in the documents documents. If the indicator does not turn on, recharge the document. Align the document indexes on each page of the document. Open the jammed document. WorkingCentre user manual 5019/5021 ... Page 90 OPEN THE COVER OF DOCUMENTS. Note when using the images for scan, close the model lid. Upload the document to face down, aligning it with the upper left corner of the scanner glass. Guide for the WorkScentre user 5019/5021 ... day (2 digits), hh = hour (2 digits), mm = minutes (2 digits) and ss = seconds (2 digits). • In some cases, the size of the scanned image may be slightly larger than the document size. The reason is a processing error. Guide for the WorkCentre user 5019/5021 ... 6-1. Start the program to load the scanned data. From the File menu, select Scanner. Select Xerox WorkCentre 5019/5021. Change other options as needed. Note for information on the scan function, click "Guide" on the screen to view the driving information. Close the scan work cancels the current scan work: press the off button on the device. Arrest button on the PC. Press Cancel on the screen displayed in SC.Screenshot of the 5019/5021 printer driver. From the File menu, choose Print. Select the name of the document you want to cancel, then press the Delete key. If there is no document in the window, delete it manually. WorkCentre 5019/5021 User Guide... Print Page 98 WorkCentre 5019/5021 User Guide... Notes – You cannot enter System Management mode if there are current or unconfirmed jobs. ¢ System Management Mode You cannot receive a print job or start a print or scan job. WorkCentre 5019/5021 User Guide ... You can change...
  • Page 14 Page 110 5: B4 6: 8.5 x 14 inches 7: 8.5 x 13 inches 9: A4 10: 8.5 x 11 customs 14: B5 16 16: B5 16: 8.5 x 11 inches 18: A5 23: B5 56: 8.5 x 13.4 inches 134: document expected 8-12 Workcende 5019/5021 page processing .2 3: 1 210 prevents the scales of downsizing defined as a factor value of 25-400 % (during the copy) to set a value between 25 and 400 % (standard: 81 %) (in passages of 1 minute). Workcenter 5019/5021 8-13 user manual ... Page 112 2: Normal* 3: Sharp +1 4: Sharp +2 4002 from the setting of the damping level. This function is 0: level 1 oppression is available if a black and white image is scanned. 1: level 2* level of the document (copy). 2: Level 3 3: Level 4 4: level 5 8-14 WorkCentre 5019/5021 User Manual ... The printed elements vary according to the settings of the device. Perform the following steps to print the relationship. Enter the management of the system. See Calling The system of management of the system on page 8-2. Enter the "202" number and click the "Start" button. Workcenter 5019/5021 User manual ... The control meter can be verified using the number of pages printed from the device. In the "meter" section of the system configuration report. Overall, the total number of printed or copied pages is displayed. Working manual 5019/5021 ... Currently no changes are needed. • It can be replaced quickly. You need a replacement soon. The state of the drum shows the status of the drum cartridge. • Currently no changes are required. ¢ will soon replace nAdministrative mode, input / logg system using the Loggor button. Workcentre 5019/5021 User manual ... p. Tambourine. Contact your Local representative Xerox. • We recommend that you always have emergency consumables / spare parts. Warning: wipe the scattered toner using a broom or wet cloth. Never use a vacuum cleaner to eliminate overturned liquids. P. Call the Customer Service Center to find out more about periodic consumables / spare parts, you must prepare code products. • Using consumables / spare parts, which Xerox does not recommend, can worsen the quality and performance of the device. Use only consumables / spare parts recommended by Xérox. By changing the toner cassette, the toner can pour and cover the ground. We recommend that you place paper on the floor earlier. • The use of toner cartridges that are not recommended for Xerox can alter image quality and performance. Use only cartridges of your recommended by Xerox. ─ ... p. Never drop the toner cassette on open fire. The toner is left in the cassette, can light up and cause burns or an explosion. You use if toner -kaset, which is no longer necessary, contact a local Xerox representative for use. Incorporate the maintenance of the new toner cartridge and shake it slightly / downwards and 10 times on the left / left. Note, do not touch the shutter. Workcentre 5019/5021 10-5 User management ... p. Close the front cover. Note: If the front cover is not completely closed, the error code will appear and the device will remain suspended. 10-6 Workcentre 5019/5021 User Guide ... These errors and icons on the device are displayed via the nearby drum. Contact youPiles can occur in hard copies or scanned documents, and the unit can correctly recognize the size of the document. WorkCentker 5019/5021 10-9 User Manager ... Document pressure and close cleaning of the glass strip If a sand document or a narrow glass strip is possible, copies or scanned documents may occur and that the machine can correctly recognize the document Size. 10- 10 WorkCentre 5019/5021 User Manager ... Page 129 Do not use cleaning agents other than water cleaning or neutral agents. If the dirt is not easily removed, clean the narrow glass strip with a soft cloth moistened with a small amount of neutral cleaning agents. WorkCentker 5019/5021 10-11 User Manager ... If dirt is not easily removed, gently clean the rollers with a soft cloth moistened with a small amount of neutral detergent. Close the power cover of the upper model until it clicks and make sure that there is no space between the two sides of the cover and access to the model. 10-12 WorkCentre 5019/5021 User Manager ... Read Problem Problem 11-16. On the page, printing more information. See Scanning Problems 11-18.
  • Page 15 The image is defined at a low resolution. Adjust the resolution to a higher resolution . Granular see Insert document 6- 1. On page. 11-20 WorkCentre 5019/5021 User Manual ... Customer Service Center. The contact number is printed on the machine attached to the machine. If a two-digit error code (X-X) is displayed, you can pressing the ID card button will display a six-digit grouped error code (xxx-xxx). WorkCentre 5019/5021 11-21 User Guide ... pg Start button. Press the STOP button to cancel the job. See the paper load 4 to 7 times. On the page. 11-22 WorkCentre 5019/5021 User Manual ... 153. 4-7. When you change the paper size and orientation, first cancel the job by pressing the STOP button. See Adjusting the Paper Size in Stores 1 and 2 4-11. WorkCentre 5019/5021 11-23 User Guide ... 154. E-5: Paper Jam in Bypass 11-34. P. The left hood of the machine is open. Close the blanket. See machine components 3-1. The front cover of the machine is open. Close the blanket. See machine components 3-1. 11-24 WorkCentre 5019/5021 User Manual ... 155. Tambour Cartridge Replacement 10-7. When you reach the maximum copy limit, press the STOP button and contact until the limit is defined. AlsoThe drum cartridge contains a spare drum cartridge. Ready. 091-441 Replace the drum cartridge soon. Prepare a spare drum cartridge. WorksCentre 5019/5021 11-27 User Manager ... Page 158 Power up the machine, make sure the screen is blank and 117-327, then power up the machine. If 123-314 happened, an error occurred. The same message appears again, contact our customer service center. 11-28 Operation Guide 5019/5021 ... WARNING: If you must remove the tray to clear a paper jam, contact your local Xerox representative. Do not remove the tray or it may injure you. If the paper is stuck around the joint unit, remove the latch. Remove the jammed paper. Note Do not leave torn pieces of paper on the unit. Return the latch to position. 11-30 WorksCentre 5019/5021 User Manager ... Page 161 If the paper is stuck in place of the chart, remove the jam by lifting. Press the center of the left cover, slowly close and lift the bypass. WorkCentre 5019/5021 11-31 User Manager ... gently close one magazine motor cover. E-3: Paper jam in reservoir 1 in the reservoir and remove the paper jam in reservoir 1. Remove the jammed paper using E-1: Krike Papos on the left cover and 11-30. Page 11-32 WorksCentre 5019/5021 User Consumer Manager ... E-4: Paper overload in basket 2 based on this and remove the paper jam in the bag. module in the reservoir. Package B 11-WorkCentre 5019/5021 11-33 User's Guide ... E-5: Paper Jam on the Bypass Follow the steps below and clear the paper jam in the bypass. Remove the jammed paper with the link to E-1: paper jam in the left cover and 11-30. Page 11-34 Corcentre 5019/5021 User Manager WorksCentre ... page 165 If multiple sheets of paper are loaded, straighten the paper loop. Insert the paper with the face, print and smooth it so that it slightly affects the van.Click Start. Use a computer to scan and restart the analysis. WorkCentre 5019/5021 11-37 User Guide ... 168 Page Solution 11-38 WorkCentre 5019/5021 User Guide ... BAC 1 (Standard) and 2 (Optional): 60-90 GSM Mounder du Bac: 60-110 GSM note. Use paper recommended by Xerox. Depending on the conditions, the copy may not be properly made. Document with the first copy of the document under the glass: 7.5 seconds. Or less (A4 document feeder: 14 pp Paper NOTE: The machine may temporarily stop image stabilization. Page 171 Monochrome: 600 × 600 DPI, 400 × 400 DPI, 300 × 300 DPI, 200 × 200 DPI. /MINUTE with standard Xerox " document (A4) at 200dpi using Twain (USB) remote control: Digitizing speed varies depending on...