Advertisement

Quick Links

Colour Television
Description
Important Safety Notice -------------------------------2
On-screen Display(OSD)------------------------ 18~29
Aging Mode ------------------------------------------- 30
Warning Message ------------------------------------ 31
Factory Mode ----------------------------------------- 32
Trouble Shooting -------------------------------------33
Panel Failure Mode ----------------------------------- 34
Wiring Diagram -------------------------------------- 35
Mechanical Instructions ------------------------ 36~37
Electrical Instructions -------------------------- 38~41
Display Adjustments -------------------------- 42~43
Safety Test Requirement ---------------------------- 44
©
Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic,
mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by JH 662 TV Service
Page
Printed in the Netherlands
Description
DDC Instructions & DDC Data ------------------ 45~52
Firmware Upgrade for CPU ---------------------- 53~54
Function Block Diagram---------------------------55~56
Scaler Schematic Diagram & C.B.A --------------57~72
Power Schematic Diagram & C.B.A --------------73~75
IR/HD Schematic Diagram & C.B.A --------------76~78
KEY Schematic Diagram & C.B.A ----------------79~80
Exploded View--------------------------------------- --81
Recommended/Spare parts list------------------82~86
Different Parts List ------------------------------------ 87
Repair Tips ---------------------------------------- 88~89
Repair Flow Chart -------------------------------- 90~91
Direction for User -------------------------------92~125
Subject to modification
Chassis
ML1.2U LA
ML1.2A LA
Page
EN 3122 785 15652

Advertisement

Table of Contents
loading

Summary of Contents for Philips ML1.2U LA

  • Page 1: Table Of Contents

    All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 662 TV Service...
  • Page 2: Important Safety Notice

    TO ENSURE THE CONTINUED RELIABILITY OF THIS Company** Equipment. The service procedures PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S recommended by Philips and described in this service REPLACEMENT PARTS, WHICH ARE LISTED WITH manual are effective methods of performing service THEIR PART NUMBERS IN THE PARTS LIST SECTION operations.
  • Page 3: General Product Specification(23")

    . Recommend resolution 1280 x 768 non-interlace at 60 Hz . WXGA 23” color TFT LCD flat panel . Easy tilt base . Anti-glare to reduce light reflection . Power management capability . VESA standard wall mount kit (option) " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 4 3.3.2 I/O interface 3.3.2.1 TV special setting 3.3.3 Electric characteristics of I/O 3.3.3.1 PC Signal type 3.3.3.2 TV Signal type 3.3.3.3 PVR output (CVBS output) Power input connection Power management 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 5 Environmental characteristics 6.1 Susceptibility of display to external environment 6.2 Transportation tests 6.3 Display disturbances from external environment Reliability 7.1 Mean time between failures Quality assurance requirements 8.1 Acceptance test Serviceability " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 6 : 615 mm W x 234 mm H x 318 mm D (Incl. Pedestal) 2.6 Unit Dimensions 2.7 Unit Weight : 11.2 Kg : 2 x 5 W 2.8 Chin speaker 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 7 FCC DOC or FCC ID / FCC Part15 Verification Energy Star EPA registration UL6500 Canda FCC DOC or FCC ID / FCC Part15 Verification Panama Colombia UL6500 /IEC60065 Ecuador Venezuela Chile Peru " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 8 Malaysia SIRIM CISPR 13 Indonesi IEC60065 IEC60065 India IEC60065 (TIS 1195-2536 ) Register with Thai Thailand Industrial Standards Institute (TISI) SASO Registration / KSS Middle IEC60065 East Registration CISPR 13 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 9 Malaysia SIRIM CISPR 13 Indonesi IEC60065 IEC60065 India IEC60065 (TIS 1195-2536 ) Register with Thai Thailand Industrial Standards Institute (TISI) SASO Registration / KSS Middle IEC60065 East Registration CISPR 13 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 10 On screen display user control via keypad and remote control for PC and TV OSD. 3.2.1 Keypad definition Top Control Panel Volume Menu Channel Left Right Down Front Control Panel Power SW Power RC sensor 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 11 4. “Up/Down” also is Channel Hot Key (TV mode). 5. Press hot Key <B> and <C> can auto-adjust picture position, phase and clock in PC mode. Power LED: Normal working: Green Power saving: Red 3.2.2 Remote control " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 12 : Positive or Negative Scanning frequency : 30 - 50 KHz 3.3.1.3 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 63 Hz Input connectors 3.3.1.4 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 13 S ( ms ) 0.317 ( 10 lines) ( 1 line ) 0.026 ( 1 line ) 0.028 + / + + / + SYNC. H/V - / - POLARITY SEP . SYNC " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 14 5. AV IN2: Component video YPbPr and composite video(Video 2) share with same audio R/L. 6. AV OUT: Composite video output (CVBS) and audio R/L(RCA jack). 7. AV IN1: Video1 (CVBS) and S-Video 1 share with same audio R/L. 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 15 WE version NAFTA version AP version China version Closed caption V-chip Teletext NAFTA version AP version CHINA version Remote Europe controller(RC5) version Channel number 100 US Air 68, cable 125 " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 16 Separate Sync. : TTL level, separate, positive or negative polarity : Mini-jack audio input, Audio signal Level: Nominal : 0.5 V rms. Maximum : 1.5 V rms. Impedance > 10 k ohm 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 17 : 3 leads power cord with protective earth plug. Power management PC mode The power consumption and the status indication of the set with power management function are as follows: Power Spec " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 18 : As defined in 3.3.1.5, 1280 x 768 x 60Hz non-interlaced mode (47.776kHz), signal sources must have 75 ohm output impedance. (2) Luminance setting: controls to be set to 500 Nits (typical) with full screen 700mv white signal. 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 19 50% position. The 1931 CIE Chromaticity (color triangle) diagram (X, Y) coordinate for the screen center should be: 8500K CIE coordinates X = 0.292 ± 0.030 Y = 0.293 ± 0.030 " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 20 Composite video input (VIDEO 1) L/R audio input (S-video1 and Video1 share with same audio) Composite video output L/R audio output YPbPr video input for component Composite video input (Video 2) L/R audio input 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 21 : 600 to 1100 mBAR Note: recommend at 0 to 35°C, Humidity less than 60 % Shipping - Temperature :( -20 to 50 : 10 to 95% (non –condensing ) - Humidity " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 22 According to MIL-STD-105D Control II level AQL : 0.65 (major) 2.5 (minor) (Please also refer to annual quality agreement) Cosmetic and dot defect of panel refer to the IIS specification of panel. 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 23 181.25 185.75 180-186 187.25 191.75 186-192 193.25 197.75 192-198 199.25 203.75 198-204 205.25 209.75 204-210 211.25 215.75 210-216 471.25 475.75 470-476 477.25 481.75 476-482 483.25 487.75 482-488 489.25 493.75 488-494 " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 24 747.25 751.75 746-752 753.25 757.75 752-758 759.25 763.75 758-764 765.25 769.75 764-770 771.25 775.75 770-776 777.25 781.75 776-782 783.25 787.75 782-788 789.25 793.75 788-794 795.25 799.75 794-800 801.25 805.75 800-806 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 25 295.25 299.75 294-300 301.25 305.75 300-306 307.25 311.75 306-312 313.25 317.75 312-318 319.25 323.75 318-324 325.25 329.75 324-330 331.25 335.75 330-336 337.25 341.75 336-342 343.25 347.75 342-348 349.25 353.75 348-354 " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 26 631.25 635.75 630-636 637.25 641.75 636-642 643.25 647.75 642-648 649.25 653.75 648-654 655.25 659.75 654-660 661.25 665.75 660-666 667.25 671.75 666-672 673.25 677.75 672-678 679.25 683.75 678-684 685.25 689.75 684-690 23" Wide LCD Monitor/TV BRAND: Philips 2005-07-01 Yikuan YU 2005-07-01...
  • Page 27 745.25 749.75 744-750 751.25 755.75 750-756 757.25 761.75 756-762 763.25 767.75 762-768 769.25 773.75 768-774 775.25 779.75 774-780 781.25 785.75 780-786 787.25 791.75 786-792 793.25 797.75 792-798 799.25 803.75 798-804 " Wide LCD Monitor/TV BRAND: PHILIPS 2005-07-01 Yikuan YU 2005-07-01...
  • Page 28: On-Screen Display(Osd)

    On Screen Display ME5P 23" Go to cover page PC MODE 1st Layer 2nd Layer 3rd Layer PICTURE COLOR TEMP NORMAL COOL W A RM BRIGHTNESS CONTRAST AUTO ADJUST IN PROGRESS STORE? MANUAL ADJUST PHASE CLOCK HORIZONTAL VERTICAL AUDIO AUTO SOUND PERSONAL VOICE MUSIC...
  • Page 29 On Screen Display ME5P 23" Go to cover page FEATURES PICTURE FORMAT WIDESCREEN (4:3) (HD 4:3) ZOOM 14:9 ZOOM 16:9 SUBTITLE ZOOM SUPER WIDE PICTURE ALIGNMENT AUTO LOCK LOCK PROGRAM CHANGE CODE CLEAR ALL BLOCK OPTION MOVIE RATING ON/OFF ON/OFF PG13 ON/OFF ON/OFF...
  • Page 30: Aging Mode

    Aging Mode ME5P 23" Go to cover page ATTENTION ATTENTION NO VIDEO INPUT NO VIDEO INPUT Access Aging.. Mode Step 1 : Select the source "PC" and then turn off LCD-TV, and disconnect Interface Cable between Monitor and PC. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] untill comes out "...
  • Page 31: Warning Message

    Warning Message ME5P 23" Go to cover page CANNOT DISPLAY THIS VIDEO MODE, CHANGE COMPUTER DISPLAY INPUT TO 1024 X 768 @ 60 Hz " " NO VIDEO INPUT OSD MAIN MENU LOCKED OSD MAIN MENU UNLOCKED...
  • Page 32: Factory Mode

    Factory Mode ME5P 23" Go to cover page Access factory. Mode how to get into factory mode menu Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] about five seconds then release all buttons.
  • Page 33: Trouble Shooting

    Trouble shooting ME5P 23" Go to cover page No Power .Check the TV power cord. Disconnect the power cord from the power outlet for 10 seconds, then reinsert the plug into the outlet. Press POWER to turn on the TV again. .Make sure the outlet is not on a wall switch.
  • Page 34 Failure Mode Of Panel ME5P 23" Go to cover page Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel.
  • Page 35: Wiring Diagram

    Wiring diagram ME5P 23" Go to cover page...
  • Page 36: Mechanical Instructions

    Mechanical Instructions ME5P 15" & 20" Go to cover page Front View 4. Remove the metal frame board - Remove the screws as shown in Fig.6-8 - Remove the metal frame board as Fig.9 Fig.1 Fig.5 Back View Fig.6 Fig.2 1.
  • Page 37 Mechanical Instructions ME5P 23" Go to cover page 6. Remove the speakers and the panel from the bezel - Remove the screws as shown in Fig.12 5. Remove all PCB - Remove the speakers from the bezel - Remove all screws as shown in Fig.10 - Remove the panel from the bezel - Remove all PCB as shown in Fig.11 Fig.10...
  • Page 38: Electrical Instructions

    Electrical Instructions ME5P 23" Go to cover page General points PC Input signal mode During the test and measuring, supply a distortion free AC 2.2.1 PRESET VIDEO RESOLUTION mains voltageto the apparatus via an isolated transformer with low internal resistance. The analogue color LCD monitor must be capable of displaying standard resolutions within the vertical frequency range of 58 - 63 Hz, and All measurements mentioned hereafter are carried out at a...
  • Page 39 Electrical Instructions ME5P 23" Go to cover page Table 3: Reading with Minolta CA-110. Item 720X576P 720X480P 720X576i 720X480i 50Hz 60Hz 50Hz 60Hz 2. Check Gain R of video SCALER GAIN, It shall be R=131 Pixel rate 27 MHz 27.027MHz 13.5MHz 13.5MHz 3.
  • Page 40 Electrical Instructions ME5P 23" Go to cover page Check the digital interface cable (B) DVI Video HDCP Key Test Check the 64 gray level color poor & noise condition. 7.2.1 Use pattern generator HDTV Mode display adjust Equipment: Quantum 802R or 802BT or equivalent equipments. 6.1 White balance adjustment (B) Pattern : Standard HDCP Pattern (It’...
  • Page 41 Electrical Instructions ME5P 23" Go to cover page 8.2 Smart picture setting Virgin Smart Smart Mode Region Model Volume Sound Picture RF Channel Format Installation PERSONAL RICH NATURE SOFT MULTIMEDIA NAFTA / Channel 2 Wide Brightness LATAM 23PF5320/28 Theater Rich (Auto) Screen Channel 2...
  • Page 42: Display Adjustments

    Display adjustment ME5P 23" Go to cover page Display adjustment Access factory. Mode how to get into factory mode menu Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power " button and then push the "VOL- " and "VOL+" buttons at the same time immediately and hold it] about five seconds Fig.3 then release all buttons.
  • Page 43 Display Adjustment ME5P 23" Go to cover page " " 2.9 Set smart picture as NORMAL Set SCALER GAIN R G B = VIDEO SCALER GAIN R G B(alignment done). The 1931 CIE chromaticity (X, Y) co-ordinates shall be: Normal/ 0.292 ±...
  • Page 44: Safety Test Requirement

    Safety Test Requirements ME5P 23" Go to cover page 3. Equipments and Connection All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both testing. Hipot Ground Continuity 3.1. Equipments For example : HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY TESTER...
  • Page 45 Go to cover page General Pin Assignment The digital only connector contains 24 signal contacts organized in DDC Data Re-programming three rows of eight contacts. Signal pin assignments are listed in the In case the DDC data memory IC or main EEPROM which storage all following table: factory settings were replaced due to a defect, the serial numbers have to be re-programmed"...
  • Page 46 Go to cover page Configuration and procedure 3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID45 (for example, C:\EDID45, as shown in Fig. 7). There are 3 chips contained OSD string, serial number..etc on the circuit board, main EEPROM which storage all factory settings,OSD string.
  • Page 47 Go to cover page To Printer port DC 8~12V DC 8~12V To Monitor D-sub/DVI cable To Monitor D-sub cable Power indicator Power indicator To PC To Monitor Printer Port To Printer port...
  • Page 48 DDC INSTRUCTIONS ME5P 23" Go to cover page Step 7: Exit DDC program Step 5: Write DDC data 1. Configuration should be as Fig. I. And press OK. Pull down the File menu and select Exit as shown in Fig. III. Fig.
  • Page 49 DDC Instructions ME5P 23" Go to cover page Step 3: Modify DDC data (verify EDID version, week, year) Re-programming Digital DDC IC Step 1: After initialize alignment box, connecting all cables and Click (new function) icon from the tool bar, bring up box as shown in Fig.
  • Page 50 DDC Instructions ME5P 23" Go to cover page Step 5: Write DDC data 1. Configuration should be as Fig. 24. And press OK. Fig. 24 2.Access factory. Mode Step 1 : Select the source "PC" and then turn off LCD-TV. Step 2 : [Push "power "...
  • Page 51 DDC DATA ME5P 23" Go to cover page : Positive Vertical Sync. For D-SUB : Negative Horizontal Sync. ********************************************************************** EDID log file (31052005_Me5P23_A_V1) Monitor Descriptor #2 ********************************************************************** Serial Number : 00001 Vendor/Product Identification ID Manufacturer Name : PHL Monitor Descriptor #3 ID Product Code : 0000 (HEX.) Monitor Name...
  • Page 52 DDC DATA ME5P 23" Go to cover page For DVI-D ********************************************************************** : Positive Vertical Sync. EDID log file (31052005_Me5P23_D_V1) : Positive Horizontal Sync. ********************************************************************** Detailed Timing #2 Vendor/Product Identification Pixel Clock (MHz) : 27 ID Manufacturer Name : PHL H Active (pixels) : 720 ID Product Code : 0000 (HEX.)
  • Page 53 ISP INSTRUCTIONS ME5P 23" Go to cover page Configuration and procedure Fig. 4 "Easywriter " The software is provided by Novatek to upgrade the firmware of CPU. It is a windows-based program, which cannot be run in MS-DOS. DDC2BI_ISP TOOL (3138 106 10396) is for the interface between "Parallel Port of PC"...
  • Page 54 ISP INSTRUCTIONS ME5P 23" Go to cover page If there is a warring message coming as shown in Fig 11. , you Press the Load hex then select the HEX CODE have to check the AC power, Video cable, or Novatek MCU. as shown in Fig.
  • Page 55 ME5P 23" BLOCK DIAGRAM Go to cover page Scaler AV3 audio AUDIO delay HD audio Sound decoder Tuner Audio MSP34XX audio video TPA3004D SC1-audio SC2-audio audio DVI Audio HDCP PC audio Tuner CVBS PC analog HD YPbPr SDRAM M51512L 1Mx16 Columbus RGB/YPbPr Panel...
  • Page 56 ME5P 23" Go to cover page Power 24V 2.5A Inverter PFC control PWM control AC to DC Transformer AC to DC L6562 & TEA1507P & EQ40 GBU6J STPS20H100CFP STP60NM60 STP10NK80Z FILTER Photo-coupler 16V 2A TCET1103(G) Panel/scalar/Audio AC to DC MBRF10H100CT AC Inlet Protection &...
  • Page 57 Go to cover page...
  • Page 58 Go to cover page...
  • Page 59 Go to cover page...
  • Page 60 Go to cover page...
  • Page 61 Go to cover page...
  • Page 62 Go to cover page...
  • Page 63 Go to cover page...
  • Page 64 Go to cover page...
  • Page 65 Go to cover page...
  • Page 66 Go to cover page...
  • Page 67 Go to cover page...
  • Page 68 Go to cover page...
  • Page 69 Go to cover page...
  • Page 70 Go to cover page...
  • Page 71 Go to cover page...
  • Page 72 Go to cover page...
  • Page 73 Go to cover page...
  • Page 74 Go to cover page...
  • Page 75 Go to cover page...
  • Page 76 Go to cover page...
  • Page 77 Go to cover page...
  • Page 78 Go to cover page...
  • Page 79 Go to cover page...
  • Page 80 Go to cover page...
  • Page 81: Exploded View

    EXPLODED VIEW ME5P 23" Go to cover page...
  • Page 82 Recommended Parts List ME5P 23" Go to cover page 7056 932222284682 IC L6562N (ST00) L 7057 932217923687 FET POW STP20NM60 (ST00) L 7061 935267356112 IC TEA1507P/N1 (PHSE) L 7062 932219657687 FET POW STP10NK80ZFP (ST00) L 7063 933953410676 TRA SIG TBC328-40 (TOSJ) A 7072 932214014667...
  • Page 83: Recommended/Spare Parts List

    2436 223891611549 CER1 0603 NP0 25V 2107 223886715331 CER1 0603 NP0 50V 330P PM5 R 0143 312123346091 Philips Product Reg. Card 2437 223878615645 CER2 0603 X7R 16V 47N PM10 R 2121 223886715109 CER1 0603 NP0 50V 10P PM5 R 313912525031 WORLD WIDE GUARANTEE CARD...
  • Page 84 ME5P 23" Go to cover page 2550 223878615649 CER2 0603 X7R 16V 100N PM10 R 2835 223824619863 CER2 0603 Y5V 10V 1U P8020 R 3137 232270260101 RST SM 0603 RC21 100R PM5 R 2551 223878615649 CER2 0603 X7R 16V 100N PM10 R 2840 223878619854 CER2 0603 Y5V 16V 220N P8020 R 3139...
  • Page 85 Spare Parts List ME5P 23" Go to cover page 3814 232270260472 RST SM 0603 RC21 4K7 PM5 R 5705 242253595853 IND FXD SM 0603 0U10 PM10 R 3516 232270260332 RST SM 0603 RC21 3K3 PM5 R 232270260102 RST SM 0603 RC21 1K PM5 R 3815 5706...
  • Page 86 ME5P 23" Go to cover page 2601 223886715331 CER1 0603 NP0 50V 330P PM5 R 3051 212211805971 RST SM 1206 RC1206 270K PM5 R 7062 932219657687 FET POW STP10NK80ZFP (ST00) L 2602 223886715331 CER1 0603 NP0 50V 330P PM5 R 3052 232271161334 RST SM 1206 RC01 330K PM5 R 7063...
  • Page 87: Different Parts List

    Different Parts List ME5P 23" Go to cover page Diversity of 23PF5320/79 compared with 23PF5320/28 Diversity of 23PF5320/98 compared with 23PF5320/28 Diversity of 23PF5320/93 compared with 23PF5320/28 Item 12NC Description Item 12NC Description Description Item 12NC 867000022249 23PF5320/79 867000021678 23PF5320/98 867000022971 23PF5320/93 0041 313815416901 BACK COVER...
  • Page 88: Repair Tips

    Repair Tips ME5P 23" Go to cover page 0. Warning preferably be equipped with a thermal control (soldering temperature: 225 to 250 C). All ICs and many other semi-conductors are susceptible to - The chip, once removed, must never be reused. electrostatic discharges (ESD).
  • Page 89 ME5P 23" Go to cover page 3. Lead-free product identification You can identify lead-free product by Philips-lead-free logo on PCB. 4. Lead-free product repair instruction 4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 149 00108(1.0mm SAC305).
  • Page 90: Repair Flow Chart

    Repair Flow Chart ME5P 23" Go to cover page 3.No picture/LED 1.No Work/LED is off is green Check if Check circuit around power switch Check if working voltage Replace power switch each regulator and is normal pin17=3.3V of 7502 eliminate short and open situation Check if clock source Replace 1502,1301,1731...
  • Page 91 Repair Flow Chart ME5P 23" Go to cover page 5.no TV sound Check if tuner 1812 output 2nd IF Replace 1812 signal Chenck 1811 7. No remote function Replace one good Try another remote control remote control Check IR receiver 8.LED and function key poor Check circuit around...
  • Page 92 Thank you for choosing Philips. Need help fast? Read your user Manual and/or Quick-Use Guide first for quick tips that make using your Philips product more enjoyable. If you have read your instructions and still need assistance, you may access our online help at www.usasupport.philips.com...
  • Page 93 ARD TODAY TO GET THE VERY MOST FROM YOUR PURCHASE Registering your model with PHILIPS makes you eligible for all of the valuable benefits listed below, so don’t miss out. Complete and return your Product Registration Card at once to ensure:...
  • Page 94 IMPORTANT SAFETY INSTRUCTIONS EAD BEFORE OPERATING EQUIPMENT Read these instructions. exhibits a marked change in performance; Keep these instructions. E. The appliance has been dropped, or the enclosure Heed all warnings. damaged. Follow all instructions. Tilt/Stability - All televisions must comply with Do not use this apparatus near water.
  • Page 95 RECAUTION ADDITIONAL SAFETY PRECAUTIONS • ENSURE that LCD TV stand is tightened properly to the set (See Quick Guide on the right way of tightening of the screw of the stand to the set. Improper tightening of screw may render the set unsafe. •...
  • Page 96 ONTENTS Introduction Welcome/Registration of Your TV ....2 Here are a few of the special features of your new LCD IMPORTANT SAFETY INSTRUCTIONS ... . 3 PRECAUTIONS .
  • Page 97: Installation

    NSTALLATION hen operate INSTALL function, the access code window will appear on the screen. Press default code (0711) or your personal code setting to enter this menu. ANGUAGE ETTINGS or English, French, Spanish or Portuguese - speaking TV owners, an onscreen LANGUAGE option is present.
  • Page 98: Tuner Mode Control

    UNER ONTROL he Tuner Mode allows you to change the LCD TV’s signal input to Cable or Air (antenna). It’s important for the LCD TV to know if you want to receive channels from a cable TV MAIN CONTROLS signal or an antenna signal. PICTURE LANGUAGE INSTALL...
  • Page 99: Auto Program (Setting Up Channels)

    ROGRAM ETTING HANNELS our LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in your area by MAIN CONTROLS pressing the CH (+) or CH (-) button. PICTURE LANGUAGE AUDIO...
  • Page 100: Channel Edit Control (To Add Or Delete Channels)

    HANNEL ONTROL hannel Edit control lets you edit the channel listing. You can add or remove a channel in the MAIN CONTROLS LCD TV’s memory. PICTURE LANGUAGE INSTALL AUDIO TUNER MODE FEATURES AUTO PROGRAM LANGUAGE CHANNEL CHANNEL EDIT INSTALL SKIPPED TUNER MODE MANUAL FINE TUNE AUTO PROGRAM...
  • Page 101: Factory Reset

    ACTORY ESET our TV can be reset to the original factory settings by performing the following steps. MAIN CONTROLS PICTURE LANGUAGE Press the MENU button on the AUDIO TUNER MODE FEATURES AUTO PROGRAM remote control to see the onscreen INSTALL CHANNEL EDIT INSTALL menu.
  • Page 102: Presentation Of The Lcd Tv

    LCD TV RESENTATION OF ositioning the LCD TV. Do not place the LCD TV near a radiator or other Place the LCD TV on a solid, stable surface. Be sure the source of heat. surface is strong enough to handle the weight of the LCD Do not place the LCD TV where it can be exposed to rain or excessive moisture.
  • Page 103: Installing Lcd Tv On The Wall

    NSTALLING The stand of your LCD TV complies with VESA standard, if you intend to install the LCD TV on the wall, please consult a professional technician for proper installing. The manufacture accepts no liability for installations not performed by professional technician. 100x100mm The manufacturer accepts no liability for improper installations or installations not performed in accordance with these instructions.
  • Page 104: Basic Tv And Remote Control Operations

    ASIC EMOTE ONTROL PERATIONS � � � � ���������������� + �� � � � � TELEVISION AND REMOTE CONTROL � � Plug the power cable into AC inlet on LCD TV set. Plug the power cord into an outlet and switch TV set on. Press POWER to turn on the LCD TV.
  • Page 105: Remote Control

    EMOTE ONTROL Status/Exit Button- Power button Press to see the current channel Press to turn the LCD TV on or off. number on the TV screen. Also press to clear the TV menu after CC button control adjustments. Press the CC button to select CC on or CC off.
  • Page 106: Timer Menu Controls

    IMER MENU CONTROLS our LCD TV comes with an onscreen clock. The TV can also be set to turn on or off at a specific time and tune to a specific channel when it powers itself on. SLEEP OFF Press the SLEEP button on the remote control to show the onscreen menu..
  • Page 107: Tv Picture Menu Controls

    TV P ICTURE ONTROLS o adjust your LCD TV picture, select a channel and follow these steps. MAIN CONTROLS Press the MENU button to see the PICTURE AUTO PICTURE PICTURE AUDIO BRIGHTNESS onscreen menu. PERSONAL AUTO PICTURE FEATURES COLOR RICH BRIGHTNESS CONTRAST INSTALL...
  • Page 108: Tv Sound Menu Controls

    TV S OUND ONTROLS o adjust your LCD TV Sound, select a channel and MAIN CONTROLS follow these steps. PICTURE AUTO SOUND AUDIO SETTINGS Press the MENU button to see the menu. FEATURES STEREO AUDIO INCREDIBLE SURROUND INSTALL AUTO SOUND PERSONAL VOICE SETTINGS...
  • Page 109: Auto Picture Control

    ICTURE ONTROL hether you’re watching a movie or a video game, your LCD TV has video control preset that will match with your current program source or content. Auto Picture quickly resets your TV’s video controls for a number of different types of programs Personal and viewing conditions that you may have in your home.
  • Page 110 MOVIE RATING TV RATING he AUTO Lock feature is an integratedcircuit that receives and PG13 processes data sent by broadcasters, or other program providers, that contain NC17 program content advisories.When programmed by the viewer, a TV with MOVIE RATINGS TV RATINGS AUTO Lock can respond to the content advisories and block program content G: General Audience - All ages...
  • Page 111: Auto Lock Access Code

    CCESS ver the next few pages you’ll learn how to block programs and understand the rating terms for certain broadcasts. First, set an access code. MAIN CONTROL PICTURE FORMAT PICTURE AUDIO PICTURE ALIGNMENT FEATURES AUTOLOCK FEATURES Press the MENU button to see the INSTALL CLOSED CAPTION LOCK PROGRAM...
  • Page 112: Auto Lock Program

    ROGRAM fter your personal access code has been set (see the previous page), you are ready to se- lect the channels or inputs you want to block out or censor. MAIN CONTROL PICTURE FORMAT PICTURE AUDIO PICTURE ALIGNMENT FEATURES AUTOLOCK FEATURES INSTALL CLOSED CAPTION...
  • Page 113: Auto Lock - Movie Ratings

    OVIE ATINGS he AUTO Lock feature can block programming based on the Movie Industry ratings. Once you’ve entered your access code and the AUTO Lock features are displayed on the MAIN CONTROL PICTURE PICTURE FORMAT screen: AUDIO PICTURE ALIGNMENT FEATURES AUTOLOCK FEATURES INSTALL...
  • Page 114: Auto Lock - Tv Ratings

    - TV R ATINGS he AUTO Lock feature can block programming based on the TV Industry ratings.Once you’ve entered your access MAIN CONTROL code and the AUTO Lock features are displayed PICTURE FORMAT PICTURE AUDIO PICTURE ALIGNMENT on the screen: FEATURES AUTOLOCK FEATURES...
  • Page 115: Using The Picture Format

    SING ICTURE ORMAT ou can change the picture format size to match the type of program you are watching. Select the normal 4:3, WIDESCREEN, ZOOM 14:9, ZOOM MAIN CONTROL 16:9, SUBTITLE ZOOM or SUPERWIDE aspect ratios. PICTURE FORMAT PICTURE PICTURE ALIGNMENT AUDIO AUTOLOCK FEATURES...
  • Page 116: Surf Control

    ONTROL list or series of previously viewed channels can be selected with the SURF button on your remote SURF EDIT ADD? control. With this feature, you can easily switch between different TV channels that currently interest SURF EDIT Delete? you. The SURF control allows you to set up to 8 SURF LIST EMPTY channels in its quick viewing list.
  • Page 117: Closed Captions

    LOSED APTIONS losed Captioning (CC) allows you to read the voice content of television MAIN CONTROL PICTURE FORMAT PICTURE programs on the TV screen. Designed to help the hear- AUDIO PICTURE ALIGNMENT FEATURES AUTOLOCK FEATURES ing impaired, this feature uses onscreen “text boxes” to INSTALL CLOSED CAPTION PICTURE FORMAT...
  • Page 118: Pc Picture Controls

    PC P ICTURE ONTROLS his TV can also be used as a PC Monitor. A PC video signal must be present or the TV will go MAIN CONTROLS PICTURE COLOR TEMP into standby mode. The PC Picture AUDIO BRIGHTNESS PICTURE FEATURES CONTRAST controls allow you to adjust the picture.
  • Page 119: Pc Audio Controls

    PC A UDIO ONTROLS his TV can also be used as a PC Monitor. A PC video signal must be present or the TV will go MAIN CONTROLS into standby mode. The AUDIO controls allow you PICTURE AUTO SOUND to adjust the sound. AUDIO SETTINGS AUDIO...
  • Page 120 PC PIP (P SING ICTURE ICTURE EATURE IP (Picture-in-Picture) feature allows you to call up a subscreen when you are using your TV as a monitor. MAIN CONTROLS Note: Make sure you are in PC mode. PICTURE PICTURE FORMAT AUDIO FEATURES FEATURES Press the MENU button to see the...
  • Page 121: Setting Up The Pc Mode

    PC M ETTING ERSONAL OMPUTER ONITOR 23PF5320 (23” LCD TV) Resolution Mode V. Frequency (Hz) H. Frequency (kHz) 640 x 480 VGA VESA 60 59.940 31.469 SVGA VESA 56 56.250 35.156 800 x 600 SVGA VESA 60 60.317 37.897 1024 x 768 XGA VESA 60 60.004 48.363...
  • Page 122: Trouble Shooting Tips

    ROUBLE HOOTING S-VHS Color Becomes Faint No Power • Unplug socket for S-Video connection. Reconnect • Check the TV power cord. Unplug the TV, wait 10 the S-Video socket of the TV carefully to the VCR seconds, then reinsert the plug into the outlet and push the POWER button again.
  • Page 123: Care And Cleaning

    LEANING WARNING concerning stationary images on the TV Screen: Do not leave fixed images on the screen for extended periods of time. This can cause uneven aging of the LCD panel. Normal use of the TV should involve viewing of programs that have constantly moving or changing images. Do not leave still images on screen for extended periods of time.
  • Page 124: Index

    NDEX Auto Program ......7, 8, 31 Balance ........17, 28 Bass .
  • Page 125: Regulatory

    EGULATORY (FCC) N (U.S. O EDERAL OMMUNICATIONS OMMISSION OTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 126: Limited Warranty

    Philips will repair or replace the product, at its WARRANTY IS THE EXCLUSIVE REMEDY FOR THE option, at no charge, or pay the labor charges to any Philips CONSUMER. PHILIPS SHALL NOT BE LIABLE FOR ANY authorized service center. After the period of one (1) year, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH Philips will no longer be responsible for charges incurred.
  • Page 127 X-radiation emissions. For continued X-radiation protection, the replacement 3. It is essential that the service technician has an accurate HV meter tube must be the same type as the original, including suffix letter,or a Philips available at all times. The calibration of this meter should be checked approved tupe.

This manual is also suitable for:

Ml1.2a la

Table of Contents