MICODUS MV710G - 4G Vehicle tracker Manual
  1. Manuals
  2. Brands
  3. MICODUS Manuals
  4. GPS
  5. MV710G
  6. User manual

MICODUS MV710G - 4G Vehicle tracker Manual

Also See for MV710G:

Advertisement

Table of Contents
Contents
MICODUS MV710G - 4G Vehicle tracker Manual

Main Features

Main Features

How to manage the tracker to get online?

  1. SIM card requirements
    Please get a suitable SIM card from your local place. The SIM card must meet below points:
    How to get online? - Step 1 - SIM card requirements
  • It must be compatible with the 4G LTE or 2G GSM network
  • Please enable SMS, call, internet data traffic of the SIM card
  • Enable the caller ID display feature
  • Remove the PIN code
  • Use Nano size SIM card for the tracker
  • Please inquire the SIM card provider for the exact correct APN information
  1. SIM card installation
    How to get online? - Step 2 - SIM card installation
  2. Wiring
    cautioncautioncaution    NOTE : After installed SIM card correctly, it is very important to connect the tracker with external power no less than 12V for power supply before operation!
    How to get online? - Step 3 - Wiring
  3. Configure APN
    Please get the exact correct APN name from local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:
SMS Command Format Reply Example Note
APN,ApnName, User, Password# SET APN OK APN,orange, orange, orange# If the SIM card has APN user and APN password, then use this command.
APN,ApnName# SET APN OK APN,internet# If the SIM card operator doesn't have APN user and APN password, then please use this command.

Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply "SET APN ok" but it will can't get online!

  1. Indicator status description
LED Event State
CELL LED
(YELLOW) 		Searching for network Flash every 1 second
Network has been registered Solid
GPS LED (BLUE) GPS is in fixing Flash every 1 second
GPS has fixed Solid
ALL LED Device is working but stopped more than 5min ALL LED TURN OFF
Device has not been turn on
Device ran out of battery

Package Content

  • GPS Main Unit x 1
  • Function Cable x 1
  • User Guide x 1
  • Genuine Packing Box x 1

Functions Explanation

  1. Cut Off Fuel/Resume Fuel
    • Set center number by this sms command:
      CENTER,A,center number#
    • Send this sms command from the center number:
      RELAY,A#
      A=0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately;
      2: Cut Off Fuel Safely)
      For example:
  2. Vibration Alert:
    This vibration alert function just work under stationary status. How to use this function:
    • Configure SOS numbers for the tracker by this sms command:
      SOS,A,1st number, 2nd number, 3rd number#
      3 SOS numbers supports at the most
    • Enable the device to enter into arm mode by this sms command:
      ARM#
    • Conifgure the alarm ways by this sms command:
      SENALM,[A][,M]#
      A=ON/OFF, default: OFF;
      M=0/1/2, way of alarming,
      0:GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default: 1
    • Keep the device under stationary status more than 5min to let it enter into sleep arm mode;
    • Vibrate the device then the tracker will send the vibration alarm messages
      For example:
  3. External Battery Low Voltage Alarm
    • Command format: LVALM,A,B,M#
      A=ON/OFF, default: ON;
      B=9-95V (voltage alarm threshold), default: 11.1v
      M=0/1/2, way of alarming, 0: Server only,
      1: SMS+Server, 2: SMS+Server+Call, default: 1;
      For example: LVA LM,ON,11.5,1#
      This means once the external battery voltage is less than 11.5v the device will send alarm message via server and sms.
      For example:
  4. Engine Start and Flameout Alarm
    • Command format: ACCALM,A,B,M#
      A=ON/OFF, Default: ON;
      B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC
      ON&OFF Alarm; Default: 2
      M: 0/1/2 (way of alarm): 0: Server only,
      1: SMS+Server, 2: SMS+Server+Call, Default: 1;
      For example: ACCALM,ON,2,1#
      This means once the device detects engine start and engine flameout it will send alarm message via server and sms.
      For example:

Installation Recomendation

Installation Recomendation

  1. The decice should face up to the sky.
  2. Metal therma barrier of heating layer of the windshield affects the signal.

Troubleshooting

Type Use

Unable to connect to tracking platform

 Check the APN and settings.
Check whether the data service of SIM card is enabled.
Check the balance of SIM card.

Tracker shows offline

 Check whether external power is still connected.
Check if the vehicle entered network blind area.
Check the balance of SIM card.

Unable to locate

 Make sure the top side facing upward without metallic things shielded.
Make sure it's not in area with no satellite coverage.

Location drift

 In area with poor GNSS signal (tall building around or basement), drifting may happen.
Check whether vibration happens around to trigger the accelerator.

No command reply

 Make sure command format is correct.
Vehicle may be in network blind area.
Make sure SIM card is well inserted and has SMS service.

Full SMS Commands List

Setting Commands
Functions Command Format Explanation
APN Setting APN,Network name[,name, password]# APN,CMNET# (if no name & Password)
APN,internet, internet, internet# (if with name & Password)
Server Setting If set with Domain Name: SERVER,1,Domain, Port# SERVER,1,d.micodus.net, 7700#
If set with IP: SERVER,0, IP,Port# SERVER,0,47.254.77.28,7700#
Check IMEI IMEI# DEVICE IMEI No. : 0123456789
Change IMEI IMEICHG,354188046912460# NEW IMEI No. : 354188046912460
Restore factory settings FACTORY# RESTORE FACTORY SETTINGS OK
Restart device RESTART# RESTARTING...1 MINUTE WILL BE OK
Internet Traffic Switch TRAFFIC,ON# OPEN TRAFFIC OK
TRAFFIC,OFF# CLOSE TRAFFIC OK
Time Zone Setting GMT,A,B,C# Example: GMT,E,8# (Means East +8 zone, no half time zone) GMT,W,9,30# (Means West -9.5 zone, has half time zone)
A: E / W, E: East time zone, W: West time zone
B: 0 ~ 12; whole time zone C: 0/15/30/45, half time zone
Set the angle upload ANGLEREP,X,A,B# Example: ANGLEREP,ON,30,3#
(Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds)
X=ON/OFF, default ON; A=5 180 degrees, diversion angle degree, default: 30 degrees
B=2 5 seconds, detecting time, default: 3 seconds,
ANGLEREP,OFF# CANCEL UPLOAD ANGLE OK
Mileage Statistics MILEAGE,A,B# Example: MILEAGE,ON,5000#
(Means enable the mileage statistics feature, the mileage initial value is 5000km)
A=ON/OFF, On/Off mileage calculation, default: Off B=0 999999 Mileage initial value, unit km; default: 0, mileage return to zero
MIELEAGE# Query current mileage
Add SOS Administrator Number SOS,A,1st number, 2nd number, 3rd number# Example:
Set 3 numbers at a time:
SOS,A,13800138000,13800138001,13800138002#
Set the first numberseparately: SOS,A,13800138000#
Set the second number separately: SOS,A,,13800138001#
Means to set 3rd number separately: SOS,A,,,13800138002#
Delete SOS Administrator Number SOS,D,1st number, 2nd number, 3rd number# or SOS,D,1,2,3# Example:
Directly delete the number:
SOS,D,13800138000#
Delete 1st number: SOS,D,1#
Delete 2nd number: SOS,D,2#
Delete the 2nd and 3rd number: SOS,D,2,3#
Add Center Number CENTER,A,center number# Example: CENTER,A,008613800138000#
(Means the tracker will just can be controlled by this number 008613800138000, 0086 is country code)
NOTE:
  1. Please set up the center number with the country code as prefix!
  2. After set up center number, the tracker will just can be controlled by center number, it will not reply commands from other numbers!
Delete Center Number CENTER,D# DEL CENTER OK
Data Upload Time Interval TIMER,T1,T2# Example:
TIMER,5,180#
(Means the tracker will upload data every 5s when ACC is on and 180s when ACC is off)
T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON,
0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;
Heartbeat Packet Upload HBT,time# Example: HBT,3#
(Means the tracker will send heartbeat data package to server every 3 min for connection maintenance)
NOTE: Range: 1-60min, default 3min.
Sensor Sensitivity LEVEL,A# Example: LEVEL,2#
(Means set up the shake sensor level to 2)
NOTE: A Sensitivity Level 1-9 (1-9 is from week to strong vibration)
Arm manually ARM# Set the device into arm mode
Disarm manually DISARM# Set the device out of arm mode
Cut Off / Resume Fuel RELAY,A#

A=1/2;

  1. Enable relay immediately
  2. Enable relay safely

For Example:

  1. RELAY,1#
    A is set to 1, the relay command will be executed immediately.
  2. RELAY,2#
    A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.
RELAY,0# RESUME FUEL OK
Inquiry Commands
Functions Command Format Explanation
Version Inquiry VERSION# Device Reply Example
: ID:9301074948
IMEI:354188046912460
ICCID:898602A51314F1298017
VERSION:MV930G_V2.0.2
BUILD:OCT 19 2016 16:31:00
Parameter Inquiry PARAM# Device Reply Example
ID:9301074948
IMEI:861157040411486
APN:CMNET IP:47.254.77.28:7700
TIMER:10,180 SPEEDLIMIT: 120km/h
ANGLERPT: 30' CENTER: 13428768257
SOS:13267052361,13488888888,13599999999
GMT:E8.00
Latitude&Longitude Inquiry WHERE# LAT:N23.02930,LON:E114.32180,COURSE:0.00,S PEED:0.00KM/H,DATETIME:2015-05-23 14:39:11
Map URL Inquiry URL# http://map.google.com/?q=22.557868,113.935090 <0.0km/h 0.0> <2014-12-12 07:32:13>
IMEI:354188047752402
Address Inquiry POSITION# NOTE: Reply message's language is determined by device's language setting, if get position content failed, device will reply Google Map location link.
Status Inquiry STATUS# BATTERY: XX% (Built-in Battery Power Percent)
INTERNET: CLOSED (No Network)
FAILED (Connecting Network or Failure)
SUCCESS (Connected to Network)
NET: NONE (No celluar Signal),
HIGH / MED / LOW (Signal Strength), 18(Signal value)
GPS: CLOSED (GPS Module Closed);
FIXED,N (Positioned and satellite number);
UNFIX,0 (Not Positioned yet)
SPEED: 30KM/H
ACC: ON / OFF (ACC on or off)
RELAY: ON / OFF (Relay on or off)
POWER: CONNECTED / DISCONNECTED (Power Connected or Disconnected), 12.5V (Vehicle battery voltage)
SENSOR: ON/OFF (Sensor on or off), LEVEL: 3 (Sensitivity level 1-9)
STATE: ARM (Arm or Disarm)
Alarms Parameters ALARM# ID: 19172012644 (ID number of device)
STATE: ARM(DISARM)(Defense status of device)
SPEED: ON/OFF(alarm status); 30km/h(alarm value);alarm way
SHIFT: ON/OFF(alarm status); 300m(alarm value);alarm way
VIBRATE: ON/OFF(alarm status);3(sensitivity level);alarm way
ACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way
POWER DOWN: ON/OFF(alarm status);alarm way
LOW VOLTAGE: ON/OFF(alarm status);alarm way
NOTE: Alarm Ways: 0/1/2 ( 0: SERVER only, 1: SMS+GPRS, 2: GPRS+SMS+CALL )
Alarm Commands
Functions Command Format Explanation
Overspeed Alarm Setting SPEED,A,B,M# Example: SPEED,ON,100,1#
(When the speed of the tracker exceeds 100km/h it will send alarm message via SMS and server)
A=ON/OFF, enable or cancel over speed alarm, default: OFF B=1 255(km/h), speed limit, default 100(km/h); M=0/1/2, way of alarm, 0: Server only, 1: SMS+Server, 2: SMS+Server+Call default 1.
SPEED,OFF# CANCEL OVERSPEED ALARM OK
Vibration Alarm Setting SENALM,A,M# Example: SENALM,ON,2#
(Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered)
A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0: Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default: 2
SENALM,OFF# CANEL VIBRATE ALARM OK
Shift Alarm Setting SHIFT,A,B,M# Example: SHIFT,ON,300,1#
(Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle's 300 meters' shift will trigger the alarm, the alarm message will be sent via SMS and server)
A=ON/OFF; default: ON B=Shift Distance (Range: 100-9999m)
M=0/1/2; way of alarm, 0: Server only, 1: SMS+Server, 2: Server+SMS+CALL, default: 1
SHIFT,OFF# CANCEL SHIFT ALARM OK
Auto Arm By ACC ACCARM,ON,M# Example:
ACCARM,ON,60#
(Means when the engine turned to off status, the tracker will enter into arm status automatically after 60s)
Arm Time: M=5-1800s, default: 60s
ACCARM,OFF# Close auto arm function
ACC Status Change Alarm ACCALM,A,B,M# Example: ACCALM,ON,2,2#
(Means enable this alarm type, tracker will send alarm message via SMS, server and call when engine start and flameout)
A=ON/OFF, Default: ON; B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default: 2 M: 0/1/2 (way of alarm): 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, Default: 1;
ACCALM,OFF# Cancel ACC alarm function
Power Disconnect Alarm PWRALM,A,M# Example: PWRALM,ON,1#
(Means when the external power disconnect the tracker will send alarm message via SMS and server)
A=ON/OFF, default ON; M=0/1/2, ways of alarming, 0: Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default: 2
PWRALM,OFF# Close power disconnect alarm
Low Voltage Alarm Setting LVALM,A,B,M# Example: LVALM,ON,11.2V,1#
(Means once the external power voltage is less than 11.5v the tracker will send alarm message out via SMS and server)
A=ON/OFF, default ON; B=9-95 V, Low voltage threshold, can be a decimal, such as 12.5 V M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default: 1
LVALM,OFF# CANCEL LOW VOLTAGE ALARM OK

Any Questions?

E-mail: support@micodus.com
Skype: MiCODUS

Download the APP

Search "MiCODUS" in iOS APP store or Google Play Store, or just scan the QR code as below to download MiCODUS APP:

www.apple.com
play.google.com

Specifications

Device Information Model MV710G
Weight 40g
Dimensions 79mm(L)*33mm(W)*16mm(H)
Battery Built-in 60 mAh 3.7V polymer battery
Working Parameters Working Voltage 9-95V DC
Working Current 12V/average 35mA
Sleep Current 12V/average 10mA
Working Temperature -20℃ - 75℃
Working Humidity 10%-85% RH non-condensing
Celluar Specifications SIM Card Micro SIM
Celluar Antenna Built-in, FPC
Working Frequency GSM/2G: 850/900/1800/1900MHz
LTE/4G: LTE-FDD:B1/B2/B3/B4/B5/B7/B8/B28/B66
GNSS Specifications GNSS GPS+BDS
GPS Frequency L1: 1575.42±1.023MHz
BDS Frequency B1:1561.098±2.046MHz
Sensitivity -162 dBm
Satellite Channels 32
Hot/Cold Start <1s, <32s @ Open Sky
Positioning Antenna Built in ceramic dielectric antenna, 18*18*4mm
Accuracy <10m(1σ)
External Interface ACC Detection 1
Cut Off Fuel/Power Standard
SOS(optional) 1
Open door Alarm (optional) 1
Microphone 1

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download MICODUS MV710G - 4G Vehicle tracker Manual

Advertisement

Need help?

Need help?

Do you have a question about the MV710G and is the answer not in the manual?

Questions and answers

Related Manuals for MICODUS MV710G

Save Article as PDF

Table of Contents