Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco 5920E
Summary of Contents for Peco 5920E
- Page 1 P P P P P P COLLECTION SYSTEM PECO PECO PECO PECO PECO & UTILITY TRAILER Model# 5920E, 5920EB, 7930E, 7930EB 5920E 5920EB 7930E 7930EB OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE Initial Release - August 2023 MANUAL PART#: Q0598...
-
Page 2: Table Of Contents
GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Dump Handle Installation - - - - - - - - - - - - - - - - - - - 15 Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-3 Wheel Installation - - - - - - - - - - - - - - - - - - - - - 16-17 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Trailer Top Installation - - - - - - - - - - - - - - - - - - - - 17... -
Page 3: Safety
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION Introduction Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 9: Operating Instructions
SECTION II Unloading The Collection System OPERATING INSTRUCTIONS NOTE: Collection system blower will have an audible change in tone when the collection system is full. General Safety A. Stop the forward movement of the mower. Only qualified people familiar with this operator’s manual B. -
Page 10: Maintenance
2. Inspect blades for wear. Replace if necessary. If it is replacement parts, contact New PECO, Inc. and include necessary to sharpen the blades, remove the blades the following information on the chart below. -
Page 11: Torque Specifications
PECO... -
Page 12: Installation For Use
Section V - INSTALLATION FOR USE Recommended Tools & Equipment For the installation of this Collection System & Utility Trailer, It is recommended to always use Personal Protective Equipment, such as safety goggles & hearing protection, while using any tool or power equipment during the installation of your Grass Collection Unit. -
Page 13: Preparation Of Parts
Section V - INSTALLATION FOR USE Preparation Of Parts PECO Trailer Vacs are shipped as shown in Figure A. Remove the hoses as shown in Figure D. Figure D Note: The following instructions are used in the installation of both the X20 Trailer Vac & X30 Trailer Vac. -
Page 14: Removing Trailer Pan
Remove all parts from trailer pan as shown in Figure G. Lift the trailer pan off of the chassis and set the trailer pan upside down as shown in Figure D. Figure G Figure D Set Trailer Pan Upside Down In Preparation Removing Trailer Pan Remove the (2) shipping screws from the front trailer... -
Page 15: Removing Trailer From Pallet
Removing Trailer From Pallet Attaching Trailer to Trailer Pan Cut and remove the remaining retaining wires as shown Flip the trailer over and place on the trailer pan as shown in Figure A. Then lift and remove the trailer from the in Figure A. -
Page 16: Wheel Installation
Insert the dump handle through the slot in the trailer pan Wheel Installation and through the handle spring P#(J0310) as shown in Figure B. Remove the tape from both axles. Refer to Figure A and Figure B for reference. Figure B Figure A Dump Handle Remove Tape... -
Page 17: Trailer Top Installation
Trailer Top Installation Figure D Lift the trailer top and place onto the trailer pan as shown (1) Flat Washer in Figure A. (1) Cotter Pin PER WHEEL Figure A Place Trailer Top Onto The Trailer Pan Flip the trailer over onto the wheels in preparation for the trailer top installation. -
Page 18: E-Drive/Blower/Blade Assembly Installation
E-Drive/Blower/Blade Assembly Blower Cone Installation Installation Insert the blower cone as shown in Figure A and secure Remove the E-Drive assembly from the box. Place the with (2) 5/16”-18 x 2-1/2” Hex Bolts P#(K0125) and (2) E-Drive on top of the mount arm as shown in Figure A. 5/16”-18 Jam Nuts P#(K0120). -
Page 19: Upper Hose Installation
Upper Hose Installation Attaching Trailer To Tractor Before attaching the Upper Hose, place a Hose Clamp Back the tractor up to the trailer tongue. Lift the trailer P#(J0060) relatively loose on both ends of the Upper tongue and slide onto the tractor hitch as shown in Hose. -
Page 20: Drive Stay Assembly Installation
Attach the ball clevis clamp assembly P#(A0336) to the Drive Stay Assembly Installation ball clevis using (1) 5/16”-18 x 2” hex bolt P#(K1159) and (1) 5/16”-18 locknut P#(K1180). Thread the adjusting rod Note: Depending on the manufacturer and style of your P#(B4311) into the ball clevis clamp assembly as shown tractor, the drive stay assembly mounting procedure may in Figure D. -
Page 21: Drive Stay Adjustments
Drive Stay Adjustments With your Drive Stay mounted it is recommended to position the E-Drive so that it sits between the rear tires and is angled about 35° to the right from the center of your tractor. This will keep the E-Drive stationary at the same position when the Trailer Vac swings left or right. - Page 22 Figure B View of Collection Unit sitting to the Right of Operator Figure C View of Collection Unit sitting to the Left of Operator...
- Page 23 Figure D - Figure F are views showing the E-Drive Positioning on a Zero Turn Mower. Figure D Position from Center < 35°...
- Page 24 Figure E View of Collection Unit sitting to the Right of Operator Figure F View of Collection Unit sitting to the Left of Operator...
-
Page 25: Universal Boot Installation
Universal Boot Installation Figure C Remove the discharge chute from the mowing deck as shown in Figure A. Drill Here Figure A Deck Opening Outline Using a jigsaw, cut along the traced outline and the Remove bottom edge of the plastic boot. Discard the cutout Discharge portion of the boot. - Page 26 If necessary, cut out the traced underside of the plastic Center the upper clamp plate P#(B2308) over the slide boot to allow for blade clearance. Refer to Figure F. plate and trace the (2) holes onto the plastic boot. Refer to Figure I.
-
Page 27: Lower Hose Installation
Insert (2) 1/4”-20 x 1” carriage bolts P#(K1025) into the Lower Hose Installation lower clamp plate P#(B2039). Insert the lower clamp plate through the cutout in the plastic boot. Push the carriage bolts in the lower clamp plate up through the Attach one end of the 7”... -
Page 28: Universal Mount Base Installation
Universal Mount Base Installation To Install the Universal Mount Base (Item #1) position and align the (4) bolt holes of the Universal Mount Base to the Engine Mount Arm Assembly (Item #2). Secure the Universal Mount Base by using (4) 5/16”-18 x 1” Carriage Bolts (Item #3) and (4) 5/16”-18 Ny-Flange Lock Nuts (Item #4). -
Page 29: E-Drive Installation
E-Drive Installation To install the E-Drive P#(A2433), locate the pivot slot on the E-Drive and the pivot bolt on the Universal Mount Base P#(A2380). See Figure A. Position the pivot slot of the E-Drive over the pivot bolt of the Universal Mount Base and rotate the E-Drive forward until the Latch Plate of the Universal Mount Base locks the E-Drive into place. -
Page 30: Impeller Blade Removal/Replacement
Impeller Blade Removal/Replacement To Remove: First, remove the M10-1.5 / 8.8 x 90 HHCS (Item #5), 7/16” Lock Washer (Item #4) and 5-Blade Washer (Item #3) from the Standard 5-Blade Impeller (Item #1). Next, remove the Standard 5-Blade Impeller (Item #1) from the EDrive Shaft. -
Page 31: E-Drive Battery Removal/Replacement
E-Drive Battery Removal/Replacement To Remove: Open the battery housing lid back to expose the (2) 82V Batteries, refer to Figure A and Figure B. The batteries can then be removed by hand. The charge level of the batteries can be checked by pressing the battery check level, see Figure C. -
Page 32: Wire Harness Installation
Wire Harness Installation Connect the Wire Harness to the connector of the Powerhead. Refer to Figure A. Adjust the position of the Wire Harness to ensure that it does not interfere with or that it is out of the way of all other components and then secure with Cable Ties at this time. -
Page 33: Jack Stand Assembly Installation
Jack Stand Assembly Installation Jack Stand options are available ONLY for the X30 Trailer Vac. To install the Jack Stand Assembly, first position the Jack Stand Mount / Gusset (Item #1) behind the Pan Support and align the bolt holes of the Jack Stand Mount / Gusset to the bolt holes of the Pan Support and Frame Brace of the Trailer Vac (Item #2). - Page 34 Jack Stand Assembly Installation (Cont.) Next, position the Jack (Item #2) in front of the Pan Support and slide the Mount tube of the Jack through the Pan Support. Refer to Figure B. Finally, secure the Jack to the Jack Stand Mount / Gusset (Item #1) by using (1) Detent Pin (Item #3) and (1) Hair Pin Clip (Item #4).
-
Page 35: Exploded Views
A2433 E-Drive Base Assembly... - Page 36 A2243 E-Drive Assembly / 5-Blade Impeller...
- Page 37 5920E X20 Trailer Vac Explosion...
- Page 38 A1115 X20 Trailer Sub-Assy Explosion...
- Page 39 A2268 Top & Pan Sub-Assy / X20 Trailer Vac Explosion...
- Page 40 A1864 Top Assy / X20 Trailer Vac Explosion...
- Page 41 A1864 Top Assy / X20 Trailer Vac Explosion (Continued)
- Page 42 A1865 Pan Assy / X20 Trailer Vac Explosion...
- Page 43 A1865 Pan Assy / X20 Trailer Vac Explosion (Continued)
- Page 44 A2269 Chassis & Engine Mount Sub-Assy / X20 Trailer Vac Explosion...
- Page 45 A0025 Engine Stay Assembly Kit Explosion...
- Page 46 7930E X30 Trailer Vac Explosion...
- Page 47 A1116 X30 Trailer Sub-Assy Explosion...
- Page 48 A2271 Top & Pan Sub-Assy / X30 Trailer Explosion...
- Page 49 A2112 Top Assy / X30 Trailer Explosion...
- Page 50 A2112 Top Assy / X30 Trailer BOM...
- Page 51 A2113 Pan Assy / X30 Trailer Explosion...
- Page 52 A2114 Door Assy / X30 Trailer Explosion...
- Page 53 A2115 Chassis & Engine Mount Sub-Assy / X30 Trailer Explosion...
- Page 54 A2200 Jack Stand Assembly w/ Jack Foot Explosion...
- Page 55 A2201 Jack Stand Assembly w/ Caster Wheel Explosion...
-
Page 56: Safety Decals
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P PECO... -
Page 57: Troubleshooting
Troubleshooting 2017 (v1.0) Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace —... -
Page 58: Warranty
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for special incidental or consequential damages. - Page 59 Notes...
- Page 60 P P P P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...