V-ZUG GAS311EKBZ Installation Instructions Manual
Built-in variants of gas hob
Hide thumbs
Also See for GAS311EKBZ:
- Operating instructions manual (24 pages) ,
- Operating instructions manual (24 pages)
Table of Contents
Advertisement
Quick Links
Installation instructions
Built-in variants of gas hob
Dials GAS311/321/731
The appliance must be installed by qualified personnel only. Each step must be carried out and checked in full in the
order specified.
Check that the local connection conditions (gas type and gas pressure) and the appliance setting match before con-
necting the appliance.
The default values for this appliance are provided on the information plate (or on the identification plate).
This appliance is not connected to a combustion by-product outlet. It must be set up and connected according to the
applicable installation conditions. Particular attention must be paid to the relevant ventilation requirements.
If installing into a combustible material, the guidelines and standards for low-voltage installations and fire protection
must be strictly observed.
All leak tests should be done with a soapy water solution. Never use an open flame to check for leaks!
Validity
These installation instructions apply to the following models:
Model number
31046
31050
31056
31073
31074
31075
General notes
Identification plate
The identification plate is located on the underside of the
hob.
▸
Affix the second identification plate (supplied) in an accessible position behind the front of the fitted cabinet beneath the appliance.
Care and maintenance
▸
Follow the care and cleaning advice in the operating instructions.
▸
Follow the basic maintenance advice in the operating instructions.
Type
GAS311EKBZ
GAS321EKBZ
GAS731EKBZ
GAS311GKBZ
GAS321GKBZ
GAS731GKBZ
1
1009430-10
Appliance class
Class 3
DIN EN 30-1-1
Identification plate
Depending on
appliance, plate
with additional
information
1009430-10
26/07/2023
Advertisement
Table of Contents
Related Manuals for V-ZUG GAS311EKBZ
Summary of Contents for V-ZUG GAS311EKBZ
- Page 1 All leak tests should be done with a soapy water solution. Never use an open flame to check for leaks! Validity These installation instructions apply to the following models: Model number Type Appliance class 31046 GAS311EKBZ Class 3 DIN EN 30-1-1 31050 GAS321EKBZ 31056 GAS731EKBZ...
- Page 2 1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 Installation accessories provided For all installation variants: Designation Art. no. 4 adjusting braces H61561 Sealing ring gas connection 18 × 13 × 1.5 mm H64006 Flush installation: Designation Art.
-
Page 3: Surface-Mounted Installation
1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 Surface-mounted installation The layout of the hob to be fitted may differ from the hob illustrated! GAS311EKBZ/GKBZ GAS321EKBZ/GKBZ GAS731EKBZ/GKBZ Y – Y T ≥90 Drawer/ Side panel cabinet... -
Page 4: Flush Installation
1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 Flush installation The layout of the hob to be fitted may differ from the hob illustrated! GAS311EKBZ/GKBZ GAS321EKBZ/GKBZ GAS731EKBZ/GKBZ Detail Z Y – Y R0–5 T ≥90 Drawer/... -
Page 5: Electrical Connection
1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 ▸ Carefully cement the appliance in and leave the silicone sealant to dry for at least 24 hours. ▸ Connect to the electrical mains connection before inserting the appliance, if necessary. Combination installation Flush-mounted combination installation is described in document 1014381. -
Page 6: Gas Connection
1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 Minimum distances and installation conditions The distance from the appliance cut-out to the back wall must be ≥50 mm and to the side walls ≥200 mm. Parts such as side walls and reinforcing strips which protrude into the installation space under the cooking zone must be made of fire-resistant material. - Page 7 1009430-10 Installation instructions 26/07/2023 Built-in variants of gas hob Dials GAS311/321/731 1009430-10 Thread length Thread length of gas connection on the appliance (external thread) So is 16 mm. If the thread length of the on-site counterpart (internal thread) Si is longer than 17 mm, the front-end seal is no longer guaranteed through the supplied green sealing ring H64006 with a height of 1.5 mm.
-
Page 8: Nozzle Table
Change injector nozzles using a 7-inch socket wrench or corresponding wrench. Designation Injector, ø in hundredths of a mm Bypass, ø in hundredths of a mm / letter code For the appliances GAS311EKBZ/GKBZ and GAS321EKBZ/GKBZ, the following gas types are available: Gas type Test gas Connection Wok burner...