Raynor CORPORAL II STANDARD Series Manual

1/2 hp chain drive wi-fi garage door opener

Hide thumbs

Table of Contents

Quick Links

STANDARD Series

1/2 hp Chain Drive

Wi-Fi

Garage Door

Opener

Model 8165WRGD

FOR RESIDENTIAL USE ONLY

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■ The door WILL NOT CLOSE unless the Protector System

aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■ The model number label is located on the front panel of your garage door opener.

■ This garage door opener is ONLY compatible with MyQ

■ ONLY enable the Timer-to-Close or MyQ remote operation feature when the garage

door opener is installed on a sectional door.

NOTE: If you are installing the garage door opener on a one-piece door, visit

www.raynor.com for installation instructions.

SERIAL NUMBER:

Please write the MyQ Serial number in the box above. See page 2.

Preparation . . . . . . . . . . . . . . . .2-5

Assembly . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . 7-14

Install the Door Control . . . . . . 15-16

Install the Protector System

Power. . . . . . . . . . . . . . . . . . 21-22

Adjustments . . . . . . . . . . . . . 23-25

Operation . . . . . . . . . . . . . . . 26-32

Maintenance . . . . . . . . . . . . . 33-34

Troubleshooting. . . . . . . . . . . 35-36

Accessories. . . . . . . . . . . . . . . . 37

Warranty. . . . . . . . . . . . . . . . . . 38

is connected and properly

Automatic Garage Door Opener

Safety & Maintenance Guide . . 39-40

Repair Parts . . . . . . . . . . . . . 41-42

Security+ 2.0

accessories.

CONTENTS

. . 17-20

www.raynor.com

Raynor Garage Doors

1101 E. River Rd.

Dixon, Illinois 61021

Table of Contents

Need help?

Do you have a question about the CORPORAL II STANDARD Series and is the answer not in the manual?

Questions and answers

Joanne Estrada

June 7, 2025

the keypad lights up, but does not open the garage door. Is the battery dead? My car sits below, so I cannot access the Garage Door Opener.

Summary of Contents for Raynor CORPORAL II STANDARD Series

Page 1: Table Of Contents
NOTE: If you are installing the garage door opener on a one-piece door, visit www.raynor.com for installation instructions. SERIAL NUMBER: Please write the MyQ Serial number in the box above. See page 2.
Page 2: Preparation
Preparation ® Serial Number Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, Write down the following information for future reference: maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the ®...
Page 3 Preparation Before You Connect with Your Smartphone Check the Door ® Monitor and control your garage door from anywhere using the myQ App. You will need: • Wi-Fi enabled smartphone, tablet or laptop To prevent possible SERIOUS INJURY or DEATH: • Broadband Internet Connection •...
Page 4 Preparation Tools Needed 5/32 3/16 7/16 5/16 7/16 9/16...
Page 5 Preparation Carton Inventory HARDWARE Accessories will vary depending on the garage door opener model purchased. Depending on your specific Installation Door Control Hardware model, other accessories may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are Hex bolt 5/16"-18 x 7/8"...
Page 6: Assembly
Assembly 1 Attach the Rail to the Garage Door Opener 2 Tighten the Chain Loosen the inner nut and lock washer on the trolley threaded shaft. Tighten the outer nut until the chain is a 1/2" above the base of the rail at the midpoint of the rail. Re-tighten the inner nut.
Page 7: Installation
DO NOT install on a one-piece door if using devices or features providing unattended close. in garage door or opener mechanisms. Unattended devices and features are to be used ONLY with sectional doors. SAVE THESE INSTRUCTIONS. NOTE: If you are installing the garage door opener on a one-piece door, visit www.raynor.com for installation instructions.
Page 8 Installation 1 Determine the Header Bracket Location OPTIONAL Unﬁnished CEILING Ceiling MOUNT FOR HEADER Header Wall To prevent possible SERIOUS INJURY or DEATH: BRACKET • Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise Vertical Centerline garage door might NOT reverse when required.
Page 9 Installation 2 Install the Header Bracket OPTION B - CEILING INSTALLATION Extend the vertical centerline onto the ceiling as shown. You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the Center the bracket on the vertical mark, no more than 6"...
Page 10 Installation 3 Attach the Rail to the Header Bracket 4 Position the Garage Door Opener Align the rail with the header bracket. Insert the clevis pin through the holes in the header bracket and rail. Secure with the ring fastener. NOTE: Use the packing material as a protective base for the garage door opener.
Page 11 Installation 5 Hang the Garage Door Opener HARDWARE To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Lock Washer 5/16" Hex Bolt 5/16"- 18x7/8" Nut 5/16"-18 supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry. Hanging your garage door opener will vary depending on your garage.
Page 12 Installation 6 Install the Light Bulbs 7 Attach the Emergency Release Rope and Handle To prevent possible OVERHEATING of the end panel or light socket: To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • • Use ONLY A19 light bulbs. If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED.
Page 13 Installation 8 Install the Door Bracket Metal, insulated or light weight factory reinforced doors: • Drill 3/16" fastening holes. Secure the door bracket using the self-threading screws. (Figure 3) Wood Doors: • Use top and bottom or side to side door bracket holes. Drill 5/16” holes through the door and secure bracket with 5/16"-18 x 2"...
Page 14 Installation 9 Connect the Door Arm to the Trolley HARDWARE IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. Close the door. Disconnect the trolley by pulling the emergency release handle. Slide the outer trolley back (away from the door) about 2"...
Page 15: Install The Door Control
Security+ 2.0 accessories, see page 37. Your garage door opener is compatible with DRYWALL up to 2 Smart Control Panels or 4 of any other Security+ 2.0 control panels. NOTE: Older Raynor control panels and third party products are not compatible.
Page 16 Door Control 2 Wire the Door Control to the Garage Door Opener 3 Attach the Warning Labels PRE-WIRED INSTALLATIONS: When wiring the door control to the garage door opener make sure you use the Attach the entrapment warning label on the wall near the door control with tacks or staples. same wires that are connected to the door control.
Page 17: Install The Protector System
® Install the Protector System Introduction Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor. To prevent SERIOUS INJURY or DEATH from closing garage door: • Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled.
Page 18 ® Install the Protector System 1 Install the Safety Reversing Sensors WALL INSTALLATION HARDWARE Make sure the brackets on each side are clear of the door track and have the same amount of clearance so the Hex Screw 10-24 (2) sensors will align correctly.
Page 19 ® Install the Protector System FLOOR INSTALLATION 2 Wire the Safety Reversing Sensors Measure the position of both sensor brackets so they will be the same distance from the wall and PRE-WIRED INSTALLATIONS: If your garage already has wires installed for the safety reversing sensors, see unobstructed.
Page 20 ® Install the Protector System OPTION B - PRE-WIRED INSTALLATION Cut the sensor wires, making sure there is enough wire to reach the pre-installed wires from the wall. Pre-installed Safety reversing wires Separate the sensor wires and strip insulation from each end. Choose two of the pre-installed wires and 7/16"...
Page 21: Power
Power 1 Connect Power THERE ARE TWO OPTIONS FOR CONNECTING POWER: OPTION A - TYPICAL WIRING Plug in the garage door opener into a grounded outlet. DO NOT run garage door opener at this time. TYPICAL WIRING To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: •...
Page 22 Power 2 Align the Safety Reversing Sensors SAFETY SENSOR TROUBLESHOOTING If either of the sensor LEDs are off, there is no power to the sensor: IMPORTANT: The safety reversing sensors MUST be connected and aligned correctly before the garage Check that you have power to the garage door opener. door opener will move in the down direction.
Page 23: Adjustments
Adjustments Introduction PROGRAMMING BUTTONS The programming buttons are located on the side panel of the garage door opener and are used to program the travel. While programming, the UP and DOWN buttons can be used to move the door as needed. PROGRAMMING BUTTONS UP Button Without a properly installed safety reversal system, persons (particularly small children) could be...
Page 24 Adjustments 1 - Program the Travel 5 Once the door is in the desired DOWN position press and release the Adjustment Without a properly installed safety reversal system, persons (particularly small children) could be Button. The garage SERIOUSLY INJURED or KILLED by a closing garage door. door opener lights will •...
Page 25 Adjustments ® 3 - Test the Safety Reversal System 4 - Test the Protector System Without a properly installed safety reversal system, persons (particularly small children) could be Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
Page 26: Operation
Operation IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. Safety reversal system MUST be tested every month. Garage door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor. Failure to adjust the garage door opener properly ALWAYS keep remote controls out of reach of children.
Page 27 100 billion new codes. Compatible with myQ garage door opener will move in the down direction. Security+ 2.0 accessories, see page 37. NOTE: Older Raynor remote controls, door controls, and third party products are not compatible. SECURITY+ 2.0 Accessories MEMORY CAPACITY...
Page 28 Operation Connect With Your Smartphone ® Learn The Wi-Fi Garage Door Opener is compatible with up to 16 myQ enabled accessories. Up to 10 devices can be Button ® paired to the Wi-Fi garage door opener’s internal gateway. These devices can be controlled with the myQ App.
Page 29 Operation Using the Door Control The following features are accessible by lifting up the push bar: LEARN A DEVICE SYNCHRONIZE THE DOOR CONTROL ® Any compatible remote controls, wireless keyless entry, or myQ accessories can be programmed to the garage To synchronize the door control to the garage door opener, press the push bar until the garage door opener door opener by pressing the LEARN button on the door control, see page 31.
Page 30 Door Control Control Panel Setup LIGHT FEATURE (Default is Active) Deactivate: LOCK Press and hold the LIGHT button until the garage door Command LED Your remote controls will NOT work when LOCK mode Command LED opener lights turn on, then off again.* is active however your keyless entry will still allow Activate: access to your garage.
Page 31 Press and hold the button on the remote control that you wish to use. Release the button when the garage accessories refer to the instructions provided with the accessory or visit www.raynor.com. If your vehicle is door opener lights blink or two clicks are heard.
Page 32 Operation To Erase the Memory To Open the Door Manually ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use.
Page 33: Maintenance
Maintenance Maintenance Schedule NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada EVERY MONTH license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 34 Maintenance The Remote Control Battery To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 3V CR2032 coin batteries. •...
Page 35: Troubleshooting
Troubleshooting Diagnostic Chart Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM SOLUTION Up Arrow Flash Down Arrow Flash (es) (es) The garage door opener will not close. Safety reversing sensors are not installed, connected, or wires may be cut.
Page 36 Troubleshooting DIAGNOSTIC CODE SYMPTOM SOLUTION Up Arrow Flash Down Arrow Flash (es) (es) Door is moving, stops or reverses. Opener beeps and lights flash. Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed.
Page 37: Accessories
893RGX 3-Button MAX Remote Control: 880RGD Smart Control Panel: Compatible with Raynor garage door openers Displays temperature, time and system diagnostics; manufactured since 1993. Includes visor clip. includes a push bar to open and close the door and a lock feature for extra security. Security+ 2.0 and Wi-Fi compatible.
Page 38: Warranty
RAYNOR®LIMITED WARRANTY Raynor® (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defects in materials and/or workmanship for a specific period of time as defined below (the “Warranty Period”).
Page 39: Automatic Garage Door Opener Safety & Maintenance Guide
Automatic Garage Door Opener Safety & Maintenance Guide Garage Door Opener Safety – An Automatic Decision A garage door is the largest moving object in the home. An improperly adjusted garage door and opener can exert deadly force when the door closes – which could lead to entrapment of children or adults and subsequent injury or death.
Page 40 Routine Maintenance Can Prevent Tragedies Make monthly inspection and testing of your garage door and opener system a part of your regular routine. Review your owner’s manual for both the door and door opener. If you don’t have the owner’s manuals, contact the manufacturer(s) and request a copy for your specific model(s).
Page 41: Repair Parts
Repair Parts RAIL ASSEMBLY PARTS INSTALLATION PARTS Description Part Number Description Part Number Master link 004A1008 3V CR2032 lithium battery K010A0020 Chain Pulley Bracket 041A4813 Remove control visor clip K02980137 Complete trolley assembly includes: 041A3489 Emergency release rope and handle 041A2828 Threaded Shaft (1), Nuts (2), Washers, 2- Conductor bell wire, white and...
Page 42 041A3150 Wire Harness 041A7946 CONTACT INFORMATION Address repair parts order to: For installation and service information call: Raynor Garage Doors 1-800-472-9667 1101 E. River Rd. Or visit us online at: Dixon, Illinois 61021 www.raynor.com Before calling, please have the model number of the garage door opener. If you are calling about a troubleshooting issue, it is recommended that you have access to your garage door opener while calling.
Page 43 Notes...

This manual is also suitable for:

Corporal ii 8165wrgd

Raynor CORPORAL II STANDARD Series Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Raynor CORPORAL II STANDARD Series

Summary of Contents for Raynor CORPORAL II STANDARD Series

This manual is also suitable for:

Table of Contents