Related Manuals for LawnMaster B261
Summary of Contents for LawnMaster B261
- Page 1 26CC BENT SHAFT LINE TRIMMER SAFETY AND OPERATING MANUAL LMCG260EH PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING THE UNIT B261 PROUDLY A STEELFORT PRODUCT NZ OWNED...
-
Page 2: Table Of Contents
TABLE OF CONTENTS OPERATOR SAFETY GETTING STARTED Assembly FEATURES & TECHNICAL DATA OPERATION Fuel & Oil Mixture Rules for Operation Preparing for Operation STARTING THE TRIMMER Cutting with Nylon Head MAINTENANCE & STORAGE Air Filter Fuel Filter Change Spark Plug TROUBLESHOOTING WARRANTY A STEELFORT PRODUCT... -
Page 3: Operator Safety
Thank you for purchasing our LawnMaster B261 when operating this product, as these are factors Line Trimmer, the information container within which cannot be built into this manual. this manual will help you to have many years of safe and trouble free use of this LawnMaster... -
Page 4: Getting Started
Maintain at least balance. 3m of clearance from combustible materials. • Always wear ear & eye protection when operat- ing the B261 trimmer. GENERAL WARNINGS • Before use, check for loose or damaged parts, OPERATION signs of oil or fuel leaks, and any other •... -
Page 5: Assembly
ASSEMBLY When assembling this machine, please follow the instructions for assembly printed. MOUNTING THE SHAFT • Push the lower part of the shaft (b) right down until the stop pin (a) slots into the hole (c) in the shaft. This is easier to do if you rotate the bottom of the shaft (b) slightly in both directions. -
Page 6: Features & Technical Data
FEATURES & TECHNICAL DATA Starter Spark Plug Shaft Connector Fuel Tank Rear Housing Cover Protection Guard Fuel Tank Cap Rear Handle Nylon Head Choke Lever Front Handle Air Filter Cover Shaft MODEL LMB261 Idle speed (r/min) 3000 +/- 300 Nylon Head Twin Line Tap &... -
Page 7: Operation
OPERATION STORING FUEL The tank to store the fuel should be clean, anti-static, high-temperature-resistant, fire prevention and safe. 1. FUEL & OIL MIXTURE IMPORTANT Two-stroke fuel may separate. Shake fuel container Never use oil for 4-cycle engine use or water-cooled thoroughly before every use. -
Page 8: Rules For Operation
please wear appropriate footwear to protect your WARNING feet and to improve footing on slippery surfaces. Always close the fuel tank cap firmly. Immediately Do not wear open-toed footwear, or go bare foot or clean all traces of fuel which may have dripped on the bare legged. - Page 9 NOTE: the “O/I” switch would always stays in “I” posi- 5. Adjust the choke lever to (on / ) position tion, please make it to “O” by hand if needed. 2. Adjust the choke lever to (off / ) postion 6.
-
Page 10: Cutting With Nylon Head
1. CUTTING WITH A NYLON HEAD If the machine is correctly assembled with the safety hood and cutting head it will cut weeds and long grass in places with difficult access, for example Looking down on the unit, the line head rotates in a along fences, walls and foundations and also around clockwise direction. - Page 11 danger of damaging other items due to objects (for 4. Wind both sides of the line on to the example stones) being thrown out. spool with tension in the same direction as shown on the inside of the spool. (See WARNING above right image).
-
Page 12: Maintenance & Storage
Always re-cleaned the nylon spool or, if required, replace the nylon spool with a new one. Always have the nylon spool re-cleaned or replaced by a LawnMaster Service Dealer. AIR FILTER Accumulated dust in the air filter will reduce engine efficiency, increase in fuel consumption, and allow abrasive particles to pass into the engine. -
Page 13: Change Spark Plug
Local LawnMaster Dealer Defective components must be disposed of as for a replacement. special waste. Ask your LawnMaster dealer or your local council for guidance. NUTS & SCREWS Periodically check that all the nuts and screws are securely tightened and the hand grips are tightly fastened. -
Page 14: Troubleshooting
IF THE TEMPERATURE OF MACHINES IS TOO HIGH • Ensure the machines have rest at regular time. • Faults which cannot be rectified with the aid of this table may be rectified by a LawnMaster Service Dealer. A STEELFORT PRODUCT... -
Page 15: Warranty
Only genuine spare parts can be used for repairs and this must be carried out by an authorised LawnMaster Services Dealer to maintain warranty. - Page 16 FIND US www.lawnmaster.co.nz lawnmasternz Steelfort Steelfort Auckland 500 Rangitikei Street, Private Bag 11045 880 Great South Road, Penrose Palmerston North, 4412, New Zealand Auckland, 1061, New Zealand 06 350 1350 09 573 1324...