Page 1 USER MANUAL PA-3622 15.6” POS Terminal Powered by Intel Celeron ® ® J1900 Quad-Core PA-3622 M2...
Page 2 PA-3622 POS System With SATA/ 3COM/5USB COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in Jan. 2018. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
Page 3 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 4: Table Of Contents
Contents Revision History ................... viii Introduction ..................1-1 About This Manual ..............1-2 Getting Started ..................2-1 Package List ................2-2 System Views ................2-3 2.2.1 Front View ................. 2-3 2.2.2 Rear View ................2-3 2.2.3 Top View ................2-4 2.2.4 Bottom View ..............
Page 5 3.5.3 VGA Port (VGA) ..............3-8 3.5.4 COM Ports (COM1, COM2, COM3) ........3-9 3.5.5 USB Ports (USB0, USB1, USB2, USB3, USB5) ..... 3-10 3.5.6 LAN Port (LAN) ..............3-10 3.5.7 Cash Drawer Port (DRW1) ..........3-11 Setting Main Board Connectors and Jumpers ......3-12 3.6.1 COM, Cash Drawer Port Voltage Selection (JP_COM2, JP_COM3) ...............
Page 6 Printer Board Component Locations & Pin Assignment ..3-30 3.7.1 Printer Board: PDAC-3100 ..........3-30 3.7.2 Jumper & Connector Quick Reference Table ....3-31 3.7.3 Setting Printer Board Connectors and Jumpers: PDAC-3100 ..................3-32 3.7.3.1 Power Supply Connector ..........3-32 3.7.3.2 RS-232 Interface Connector ........
Page 7 3.7.6.7 USB Interface Connector ..........3-49 3.7.7 Setting Printer Board: PDAC-9100 ........3-50 3.7.7.1 Operation Precautions ..........3-50 3.7.7.2 Printer Board: PDAC-9100 ........... 3-50 3.7.7.3 PDAC-9100 Connector Quick Reference Table ... 3-51 3.7.7.4 Power Connector Pin Assignment ....... 3-52 3.7.7.5 Auto-Cutter Connector Pin Assignment .......
Page 8 Introduction ................4-2 ® Installing Intel Chipset Software Installation Utility ....4-3 ® 4.2.1 Installing Intel Chipset Driver ........... 4-3 Installing VGA Driver Utility ............4-4 Installing LAN Driver Utility ............4-5 Installing Sound Driver Utility ............ 4-6 Installing Fingerprint Driver Utility (Optional) ......4-7 Installing Wireless Module Driver Utility (Optional) ....
Page 9 4.10 API Function ................4-100 4.10.1 Cash Drawer Function ........... 4-100 4.10.2 Watch Dog Function ............4-101 BIOS SETUP ..................5-1 Introduction ................5-2 Accessing Setup Utility .............. 5-3 Main ................... 5-7 Advanced .................. 5-9 5.4.1 Advanced – ACPI Settings ..........5-10 5.4.2 Advanced –...
Page 10 Save & Exit ................5-35 Appendix A System Diagrams ............ A-1 Exploded Diagram For System Top Case ..........A-2 LCD Module With Touch Exploded Diagram ..........A-4 System Exploded Diagram ...............A-5 Exploded Diagram For HDD ..............A-7 Exploded Diagram For MSR Module ............A-8 Fingerprint Module Exploded Diagram .............A-9 3-Inch Printer Exploded Diagram (1) ............A-10 3-Inch Printer Exploded Diagram (2) ............
Page 11: Revision History
Revision History The revision history of PA-3622 User Manual is described below: Version No. Revision History Page No. Date Initial Release 2017/11/27 Revised the specification of 2-7 to 2-9 2018/01/31  Customer Display and Printer in Section 2.3 System Specifications.
Page 12: Introduction
Introduction This chapter provides the introduction for the PA-3622 system as well as the framework of the user manual. The following topic is included: • About This Manual Page: 1-1 PA-3622 SERIES USER MANUAL...
Page 13: About This Manual
Chapter 1 Introduction 1.1 About This Manual Thank you for purchasing our PA-3622 system. The PA-3622 is an updated system designed to be comparable with the highest performance of IBM AT personal computers. The PA-3622 provides faster processing speed, greater expandability and can handle more tasks than before.
Page 14: Getting Started
Getting Started This chapter provides the information for the PA-3622 system. It describes how to set up the system quickly and outlines the system specifications. The following topics are included: • Package List • System Overview • System Diagrams • System Specification •...
Page 15: Package List
Item Q’ty PA-3622 Manual / Driver DVD Quick Reference Guide AC Power Cord (Optional) MSR Card Reader (Optional) i-Button + MSR Card Reader (Optional) Wireless LAN (IEEE 802.11 b+g) (Optional) VFD (Optional) Page: 2-2 PA-3622 SERIES USER MANUAL...
Page 16: System Views
Chapter 2 Getting Started 2.2 System Views 2.2.1 Front View Unit: mm 2.2.2 Rear View Page: 2-3 PA-3622 SERIES USER MANUAL...
Page 17: Top View
Chapter 2 Getting Started 2.2.3 Top View Unit: mm Page: 2-4 PA-3622 SERIES USER MANUAL...
Page 18: Bottom View
Chapter 2 Getting Started 2.2.4 Bottom View 2.2.5 Side View Unit: mm Page: 2-5 PA-3622 SERIES USER MANUAL...
Page 19: System Specifications
 1 + 1 (option, with Y cable) x RJ11 (+12V or +24V Cash Drawer selectable) DC IN  1 x 4-pin DC Power Jack Peripheral  VFD, 20 columns and 2 lines, each column is 5 x 7 Customer Display dots Page: 2-6 PA-3622 SERIES USER MANUAL...
Page 20 Printer Printable dots per line 3inch 576 dots Maximum print speed 2inch 200 mm/s; 3inch 170 mm/s Print width 2inch 54 mm; 3inch 72mm Paper width 2inch 58 +0/-1 mm; 3inch 80 +0/-1 mm Page: 2-7 PA-3622 SERIES USER MANUAL...
Page 21 Minimum paper cutting 10 mm length Cutting processing time Approx. 0.5 s/cycle Cutting frequency 1 cut/2 s max. Standard Code • CP-437, CP-850, CP-857, CP-737, CP-852, CP-860,CP-862, CP-863, CP-865, CP-866, CP-1250,CP-1251, CP-1252, CP-1253, CP-1254, CP-1257, Katakana Page: 2-8 PA-3622 SERIES USER MANUAL...
Page 22  24 ~ 30 degree Environment EMC & Safety  CE / FCC Operating Temp.  0°C ~ 35°C (32°F ~ 95°F) Storage Temp.  -5°C ~ 60°C (23°F ~ 140°F) Humidity  20% ~ 90% Page: 2-9 PA-3622 SERIES USER MANUAL...
Page 23: Safety Precautions
Avoid direct sunlight exposure for a long period of time (for example, in a closed car in summer time. Also avoid the system from any heating device.). Or do not use PA-3622 when it has been left outdoors in a cold winter day. •...
Page 24: System Configuration
• Printer Board Component Locations & Pin Assignment • Setting Printer Board Connectors and Jumpers PDAC-3100  MB-1030 series  MB-1011 & MB-1013  PDAC-9100  • Setting VFD Board Connectors and Jumpers • Setting MSR Page: 3-1 PA-3622 SERIES USER MANUAL...
Page 25: External System I/O Ports Diagram & Pin Assignment
Chapter 3 Hardware Configuration 3.1 External System I/O Ports Diagram & Pin Assignment 3.1.1 Rear I/O Ports Diagram Side I/O Power USB5 Button Page: 3-2 PA-3622 SERIES USER MANUAL...
Page 26: Jumper & Connector Quick Reference Table
Power Connector DC12V, DC24V Reserved Connectors SPK2_1, GPIO1 MSR / Card Reader Connector SATA1, SATA2, SATA_PWR1, SATA & SATA Power Connectors SATA_PWR2 Embedded Display Port (EDP) Connector EDP1 Touch Panel Connector TOUCH1 Mini-PCIe Connector M_PCI_E1 Page: 3-3 PA-3622 SERIES USER MANUAL...
Page 27: Component Locations And Jumper Settings Of System Main
Make sure both the system and peripheral devices are turned OFF as sudden surge of power could damage sensitive components. Make sure PA-3622 is properly grounded. CAUTION: Observe precautions while handling electrostatic sensitive components. Make sure to ground yourself to prevent static charge while you are working on the connectors and jumpers.
Page 28 CAUTION: Always touch the motherboard components by the edges. Never touch components such as a processor by its pins. Take special cares while you are holding electronic circuit boards by the edges only. Do not touch the mainboard components. Page: 3-5 PA-3622 SERIES USER MANUAL...
Page 29: How To Set Jumpers
2 to create one setting and shorting. You can also select to connect pins 2 and 3 to create another setting. The format of the jumper picture will be illustrated throughout this manual. The figure below shows different types of jumpers and jumper settings. Page: 3-6 PA-3622 SERIES USER MANUAL...
Page 30 Chapter 3 Hardware Configuration Jumper diagrams Jumper settings Page: 3-7 PA-3622 SERIES USER MANUAL...
Page 31: Function Buttons And I/O Ports
Description: DC Power-In Port (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT +24V +24V DC_IN 3.5.3 VGA Port (VGA) Port Name: VGA Description: VGA Port, D-Sub 15-pin (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT GREEN BLUE DDCA DATA HSYNC VSYNC DDCA CLK Page: 3-8 PA-3622 SERIES USER MANUAL...
Page 32: Com Ports (Com1, Com2, Com3)
COM4_1 is selected as the printer control interface. Port Name: COM4 (optional) Description: D-Sub9 Serial Port (rear I/O), Co-lay with COM4_1 ASSIGNMENT ASSIGNMENT COM4/ (optional) RI/+5V/+12V selectable (Max. current: 1A) Page: 3-9 PA-3622 SERIES USER MANUAL...
Page 33: Usb Ports (Usb0, Usb1, Usb2, Usb3, Usb5)
Ethernet connection. RB Ver. LAN LED Color Status Description Indicator Left Side Orange Blink Giga LAN connection is activated. Green Blink 10/100Mbps LAN connection is activated. Right Side Green LAN switch/hub connected. Page: 3-10 PA-3622 SERIES USER MANUAL...
Page 34: Cash Drawer Port (Drw1)
Chapter 3 Hardware Configuration 3.5.7 Cash Drawer Port (DRW1) Port Name: DRW1 Description: DRW1 is used by default. ASSIGNMENT DRW2 Sense GPIO1 / DRW1 Draw1 Sense 12V/24V (Max. current: 1A) GPIO2 / DRW2 DRW1 Page: 3-11 PA-3622 SERIES USER MANUAL...
Page 35: Setting Main Board Connectors And Jumpers
SETTING (Default Setting) JP_COM2 JP_COM3 +12V JP_COM3 JP_COM2 JP_COM2 JP_COM3 COM1 / COM4 /DRW1 The voltages of the external ports "COM1 & COM4 & Cash Drawer" can be adjusted via BIOS for your convenience. Page: 3-12 PA-3622 SERIES USER MANUAL...
Page 36: I-Button Connector (I-But)
Jumper Name: JP10, JP11, JP12 Description: i-Button Function Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION COM2 JP10/JP11/JP12/ (Default Setting) I-BUT* JP10/JP11/JP12/ *COM2 & COM2_1 will not function when jumpers JP10, JP11 & JP12 are set as “I-BUT”. PA-3622 SERIES USER MANUAL Page: 3-13...
Page 37: Cash Drawer Control Selection (Jp15)
You can split DRW1 into two channels of DRW1-1 & DRW1-2 using the Y-Cable (option). Jumper Location: JP15 Description: Cash Drawer 2 Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION DRW1-1 & DRW1-2 JP15 DRW1-1 only JP15 Page: 3-14 PA-3622 SERIES USER MANUAL...
Page 38 Chapter 3 Hardware Configuration Step 3. DRW1, DRW1-1, DRW1-2 shares the same power source. (Default: 12V). SIO Address Cash drawer 1 LDN 06, 0x91 bit 2 Cash drawer 2 LDN 06, 0x91 bit 3 Page: 3-15 PA-3622 SERIES USER MANUAL...
Page 39 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. Page: 3-16 PA-3622 SERIES USER MANUAL...
Page 40 Note: The DRW2 Port can function only when the optional "Printer Kit" is installed on PA-3622. The DRW2 signals from the printer board (MB-1030, MB-1011, MB-1013, PDAC-3100, PDAC-9100) can be controlled via relevant commands. See the picture below for the location of DRW2 port:...
Page 41: Usb Connectors (Usb6, Usb7)
“MINI-PCIE” port. USB6/ USB6 can function only when JP13 is set as 1-3, 2-4[short]. USB7 USB7 signal is shared from the “Touch Controller”. USB7 can function only when JP8, JP9 are set as 1-2[short]. Page: 3-18 PA-3622 SERIES USER MANUAL...
Page 42: Led Connector (Led1)
Chapter 3 Hardware Configuration 3.6.7 LED Connector (LED1) Connector Location: LED1 Description: Power indication LED connector ASSIGNMENT PWR_LED LED1 3.6.8 Speaker Connector (SPK1_1) Connector Location: SPK1_1 Description: Speaker Connector ASSIGNMENT HD_FRONT-OUT-R HD_FRONT-OUT-L SPK1_1 Page: 3-19 PA-3622 SERIES USER MANUAL...
Page 43: Power Connectors (Dc12V, Dc24V)
Chapter 3 Hardware Configuration 3.6.9 Power Connectors (DC12V, DC24V) Connector Location: DC12V Description: DC 12 Voltage Provider Connector ASSIGNMENT VCC12 VCC12 DC12V Connector Location: DC24V Description: Power for Thermal Printer Connector ASSIGNMENT VCC24 VCC24 DC24V Page: 3-20 PA-3622 SERIES USER MANUAL...
Page 44: Reserved Connectors (Spk2_1, Gpio1)
Description: External audio phone jack reserved connector ASSIGNMENT HD_FRONT-OUT-L HD_FRONT-OUT-R SPK2_1 Connector Location: GPIO1 Description: 2 ports GPIO & DC5V & DC3.3V reserved connector ASSIGNMENT GPIO1 GPIO2 5V (Maximum current: 0.5A) 3.3V ((Maximum current: 0.5A) GPIO1 Page: 3-21 PA-3622 SERIES USER MANUAL...
Page 45: Mini Pcie Usb Selection (Jp13)
Mini PCIE USB Selection (JP13) Jumper Location: JP13 Description: "USB6 signal support to" selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION USB signal to 3-5, 4-6 mini-PCIE JP13 USB signal to 1-3, 2-4 USB6 wafer (Default Setting) JP13 Page: 3-22 PA-3622 SERIES USER MANUAL...
Page 46: Msr / Card Reader Connector (Ps2)
Chapter 3 Hardware Configuration 3.6.12 MSR / Card Reader Connector (PS2) Connector Location: PS2 Description: MSR / Card reader connector ASSIGNMENT KB_CLK (Output) KB_CLK_C (Input) KB_DATA_C (Input) KB_DATA (Output) Page: 3-23 PA-3622 SERIES USER MANUAL...
Page 47: Embedded Display Port (Edp) Connector (Edp1)
3.6.13 Embedded Display Port (EDP) Connector (EDP1) Connector Location: EDP1 Description: Embedded Display Port (EDP) Connector ASSIGNMENT ASSIGNMENT EDP_DCR_EN DDI1_TX0_DP EDP_SELF_TEST DDI1_TX0_DN EDP_CONN_HPD EDP_BL_ENA DDI1_EDP_AUX_DP DDI1_EDP_AUX_DN VCC12 VCC12 EDP_PWM_DIM VCC12 EDP1 VCC12 EDP_VCC EDP_VCC Page: 3-24 PA-3622 SERIES USER MANUAL...
Page 48: Touch Panel Connector (Touch1)
Chapter 3 Hardware Configuration 3.6.14 Touch Panel Connector (TOUCH1) Connector Location: TOUCH1 Description: Touch Panel Connector ASSIGNMENT TOUCH1 Page: 3-25 PA-3622 SERIES USER MANUAL...
Page 49: Touch Panel Signal Interface Selection (Jp8, Jp9)
Chapter 3 Hardware Configuration 3.6.15 Touch Panel Signal Interface Selection (JP8, JP9) Jumper Location: JP8, JP9 Description: Control connectors for touch panel signal interface JUMPER SELECTION JUMPER ILLUSTRATION SETTING USB7 JP8: 1-2 Connector JP9: 1-2 Page: 3-26 PA-3622 SERIES USER MANUAL...
Page 50: Sata & Sata Power Connector
3.6.16 SATA & SATA Power Connector (SATA1, SATA2, SATA_PWR1, SATA_PWR2) Connector Location: SATA1, SATA2 Description: Serial ATA connectors ASSIGNMENT SATA1 SATA2 Connector Location: SATA_PWR1, SATA_PWR2 Description: Serial ATA power connectors ASSIGNMENT SATA_PWR1 VCC12 SATA_PWR2 Page: 3-27 PA-3622 SERIES USER MANUAL...
Page 51: Bios Update Selection (Jp1)
Step 4. Power on the PC and the PC will then auto-reboot for once in order to set SoC’s register. Step 5. Done! SELECTION JUMPER SETTING JUMPER ILLUSTRATION Open Normal (Default Setting) Clear CMOS* Note: Please make sure the main power is off before you clear CMOS data. . Page: 3-28 PA-3622 SERIES USER MANUAL...
Page 52 +1.5V CLKREQ# Reserved Reserved REFCLK1- Reserved M_PCI_E1 REFCLK1+ Reserved Reserved Reserved Reserved Reserved PERST# PERn0 +3.3SB PERp0 +1.5V SMB_CLK PETn2 SMB_DATA PETp2 USB D- USB D+ +3.3V +3.3V Reserved Reserved Reserved +1.5V Reserved +3.3V PA-3622 SERIES USER MANUAL Page: 3-29...
Page 53: Printer Board Component Locations & Pin Assignment
Chapter 3 Hardware Configuration 3.7 Printer Board Component Locations & Pin Assignment 3.7.1 Printer Board: PDAC-3100 Figure 3-2. PDAC-3100 Printer Board Component Locations Page: 3-30 PA-3622 SERIES USER MANUAL...
Page 54: Jumper & Connector Quick Reference Table
Chapter 3 Hardware Configuration 3.7.2 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector RS-232 Interface Connector Auto-Cutter Connector USB Connector Thermal Head/Motor/Sensor Connector Terminal Assignment Connector Page: 3-31 PA-3622 SERIES USER MANUAL...
Page 55 Chapter 3 Hardware Configuration 3.7.3 Setting Printer Board Connectors and Jumpers: PDAC-3100 3.7.3.1 Power Supply Connector CN1: Power supply wafer ASSIGNMENT +24V +24V 3.7.3.2 RS-232 Interface Connector CN7: RS-232 interface connector ASSIGNMENT ASSIGNMENT Page: 3-32 PA-3622 SERIES USER MANUAL...
Page 56 2A-2 Auto-cutter motor drive signal 1B-1 Auto-cutter motor drive signal 1B-2 Auto-cutter motor drive signal 1A-1 Auto-cutter motor drive signal 1A-2 Auto-cutter motor drive signal 3.7.3.4 USB Connector CN8: USB Connector ASSIGNMENT ASSIGNMENT Vbus Page: 3-33 PA-3622 SERIES USER MANUAL...
Page 57 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND Head GND LATCH Print data latch Head drive power Head drive power Head drive power Head drive power Page: 3-34 PA-3622 SERIES USER MANUAL...
Page 58 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal Page: 3-35 PA-3622 SERIES USER MANUAL...
Page 59 Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused Page: 3-36 PA-3622 SERIES USER MANUAL...
Page 60: Printer Board: Mb-1030 Series
Chapter 3 Hardware Configuration 3.7.4 Printer Board: MB-1030 series CUT_CN1 COM1 9 10 USB_CN1 24V_CN1 PRINT_CN1 Figure 3-3. MB-1030 Printer Board Component Locations Page: 3-37 PA-3622 SERIES USER MANUAL...
Page 61: Jumper & Connector Quick Reference Table
Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector 24V_CN1 RS-232 Interface Connector COM1 Thermal Head/Motor/Sensor Connector PRINT_CN1 Auto-Cutter Connector CUT_CN1 Paper-Near-END Sensor Connector USB Interface Connector USB_CN1 Terminal Assignment Connector Page: 3-38 PA-3622 SERIES USER MANUAL...
Page 62 Setting Printer Board Connectors and Jumpers: MB-1030 3.7.5.1 Power Supply Connector 24V_CN1: Power Supply Wafer ASSIGNMENT +24V +24V 24V_CN1 3.7.5.2 RS-232 Interface Connector COM1: RS-232 Interface Connector ASSIGNMENT ASSIGNMENT DSR /CTS DTR /RTS 9 10 COM1 Page: 3-39 PA-3622 SERIES USER MANUAL...
Page 63 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND Head GND LATCH Print data latch Head drive power Head drive power Head drive power Head drive power Page: 3-40 PA-3622 SERIES USER MANUAL...
Page 64 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal Page: 3-41 PA-3622 SERIES USER MANUAL...
Page 65 1A-2 Auto-cutter motor drive signal 3.7.5.5 Paper-Near-END Sensor Connector CN2: Paper-near-end sensor connector ASSIGNMENT FUNCTION Power supply of the near end sensor Signal of the near end sensor GND of the near end sensor Page: 3-42 PA-3622 SERIES USER MANUAL...
Page 66 Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused Page: 3-43 PA-3622 SERIES USER MANUAL...
Page 67: Setting Printer Board Connectors And Jumpers: Mb-1011
Chapter 3 Hardware Configuration 3.7.6 Setting Printer Board Connectors and Jumpers: MB-1011 & MB-1013 MB-1013 MB-1011 Figure 3-4. MB-1011 & MB-1013 Printer Board Component Locations Page: 3-44 PA-3622 SERIES USER MANUAL...
Page 68: Jumper & Connector Quick Reference Table
Chapter 3 Hardware Configuration 3.7.6.1 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector RS-232 Interface Connector Auto-Cutter Connector Thermal Head/Motor/Sensor Connector Terminal Assignment Connector USB Interface Connector Page: 3-45 PA-3622 SERIES USER MANUAL...
Page 69 Chapter 3 Hardware Configuration 3.7.6.2 Power Supply Connector CN1: Power supply wafer ASSIGNMENT +24V +24V 3.7.6.3 RS-232 Interface Connector CN7: RS-232 interface connector ASSIGNMENT ASSIGNMENT Page: 3-46 PA-3622 SERIES USER MANUAL...
Page 70 Head drive power Head drive power Head drive power Head drive power Print data output Synchronizing signal for print data transfer Head GND Head GND Head GND Head GND Head GND Head GND Unused Page: 3-47 PA-3622 SERIES USER MANUAL...
Page 71 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal Page: 3-48 PA-3622 SERIES USER MANUAL...
Page 72 Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused 3.7.6.7 USB Interface Connector CN8: USB interface connector ASSIGNMENT Vbus Page: 3-49 PA-3622 SERIES USER MANUAL...
Page 73: Setting Printer Board: Pdac-9100
• While plug and pull cable, please ensure the power is off. • Please notice that no foreign matters close to PCB, in order to avoid short circuit. 3.7.7.2 Printer Board: PDAC-9100 Page: 3-50 PA-3622 SERIES USER MANUAL...
Page 74: Pdac-9100 Connector Quick Reference Table
Chapter 3 Hardware Configuration 3.7.7.3 PDAC-9100 Connector Quick Reference Table Connector NAME Power Connector TPH, Motor and Sensor Connector Auto-Cutter Connector Key, Status and Drawer Connector Paper Near End Sensor Connector Serial Interface Connector USB Connector Page: 3-51 PA-3622 SERIES USER MANUAL...
Page 75: Power Connector Pin Assignment
CUT_OUT12 Auto-cutter motor excitation signal CUT_OUT12 Auto-cutter motor excitation signal CUT_OUT21 Auto-cutter motor excitation signal B CUT_OUT21 Auto-cutter motor excitation signal B CUT_OUT11 Auto-cutter motor excitation signal A CUT_OUT11 Auto-cutter motor excitation signal A Page: 3-52 PA-3622 SERIES USER MANUAL...
Page 76: Tph, Motor And Sensor Connector Pin Assignment
TH2_2 Ground power for thermistor Thermally sensitive resistor input terminal N.C.3 No contact Thermal head energizing control /DST2 signal Thermal head energizing control /DST1 signal GND4 GND11 GND5 GND12 GND6 GND13 /LAT Data latch PA-3622 SERIES USER MANUAL Page: 3-53...
Page 77 Power for paper out sensor GND7 Head up sensor N.C.2 No contact FGS1 FGS2 N.C.5 No contact Stepping motor excitation signal Stepping motor excitation signal B Stepping motor excitation signal A Stepping motor excitation signal Page: 3-54 PA-3622 SERIES USER MANUAL...
Page 78: Key, Status And Drawer Connector Pin Assignment
/DRAWER 2 Drawer 2 3.7.7.8 Paper Near End Sensor Connector Pin Assignment CN6: DNP/SH3/(3pin/1.0mm/90)SMD ASSIGNMENT FUNCTION Power for paper near end sensor PAPER_NEAR-END_SNS Paper near end sensor signal Ground power for paper near end PA-3622 SERIES USER MANUAL Page: 3-55...
Page 79: Serial Interface Connector Pin Assignment
3.7.7.11 Electrical Characteristics 1. Supply voltage: 24V 2. Current consumption (at 24V, maximum simultaneously activated dot is 288, 25 °C °F Two-part energization mode: Mean: Approximately 1.36A Peak: Approximately 5A Standby Current: Mean: 0.3A Page: 3-56 PA-3622 SERIES USER MANUAL...
Page 80: Vfd Board Component Locations & Pin Assignment
Chapter 3 Hardware Configuration 3.8 VFD Board Component Locations & Pin Assignment 3.8.1 VFD Board: MB-4103, LD720 JP12V Figure 3-5. MB-4103 & LD720 VFD Board Component Locations Page: 3-57 PA-3622 SERIES USER MANUAL...
Page 81: Jumper & Connector Quick Reference Table
Chapter 3 Hardware Configuration 3.8.2 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Switch Selection JP12V RS-232 Serial Interface Connector Page: 3-58 PA-3622 SERIES USER MANUAL...
Page 82: Setting Mb-4103 & Ld720 Vfd Board Connectors And Jumpers
Chapter 3 Hardware Configuration 3.8.3 Setting MB-4103 & LD720 VFD Board Connectors and Jumpers 3.8.3.1 Power Switch Selection JP12V: Power Switch Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION JP12V (Default) JP12V Page: 3-59 PA-3622 SERIES USER MANUAL...
Page 83: Serial Interface Connector
Chapter 3 Hardware Configuration 3.8.3.2 RS-232 Serial Interface Connector CN1: RS-232 serial interface wafer ASSIGNMENT ASSIGNMENT +12V/+5V Page: 3-60 PA-3622 SERIES USER MANUAL...
Page 84: Msr Board Component Locations & Pin Assignment
3.9 MSR Board Component Locations & Pin Assignment 3.9.1 ID TECH ID-TECH MSR Board Component Locations 3.9.1.1 Main Connector ASSIGNMENT ASSIGNMENT K-CLK Chassis Ground (Computer connections) P-CLK K-DATA (Keyboard connections) (Computer connections) P-DATA (Keyboard connections) +5V Vcc Page: 3-61 PA-3622 SERIES USER MANUAL...
Page 85: Information Button Reader
MB-3012 MSR Board Component Locations 3.9.2.1 Information Button Reader I_BUTTON1: Information button reader ASSIGNMENT I_B1 I_BUTTON1 3.9.2.2 Output Connector IO1: Output wafer ASSIGNMENT ASSIGNMENT CLK_KB RX_MSR CLK_PC TX_MSR DATA_KB DATA_PC USB_D+_R USB_D-_R CHASSIS GND Page: 3-62 PA-3622 SERIES USER MANUAL...
Page 86: Software Utilities
• Installing LAN Driver Utility • Installing Sound Driver Utility • Installing Fingerprint Driver Utility (Optional) • Installing Wireless Module Driver Utility (Optional) • Peripheral Devices - Printer - VFD - MSR • API PA-3622 SERIES USER MANUAL Page: 4-1...
Page 87: Introduction
Chapter 4 Software Utilities 4.1 Introduction Enclosed with the PA-3622 Series package is our driver utilities contained in a DVD-ROM disk. Refer to the following table for driver locations: Filename (Assume that Win7 Win8.1 Win10 Purpose DVD- ROM drive (32/64...
Page 88: Installing Intel ® Chipset Driver
10 series, and it should be installed right after the OS installation. Please follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk. Enter the “Main Chip” folder where the Chipset driver is located (depending on your OS platform).
Page 89: Installing Vga Driver Utility
Chapter 4 Software Utilities 4.3 Installing VGA Driver Utility The VGA interface embedded with PA-3622 can support a wide range of display types. You can have dual displays via CRT & LVDS interfaces work simultaneously. To install the Graphics driver, follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk.
Page 90: Installing Lan Driver Utility
Chapter 4 Software Utilities 4.4 Installing LAN Driver Utility PA-3622 is enhanced with LAN function that can support various network adapters. To install the LAN Driver, follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk.
Page 91: Installing Sound Driver Utility
8.1 & Windows 10 series. To install the Sound Driver, follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk. Enter the “Sound” folder where the sound driver is located (depending on your OS platform).
Page 92: Installing Fingerprint Driver Utility (Optional)
OS installation. To install the fingerprint driver, follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk. Enter the “Device\Embedded Finger Printer” folder where the fingerprint driver is located.
Page 93: Installing Wireless Module Driver Utility (Optional)
10 series, and it should be installed right after the OS installation. To install the wireless driver, follow the steps below: Connect the USB DVD-ROM device to PA-3622 and insert the driver disk. Enter the “Device\Embedded Wireless Module” folder where the wireless driver is located.
Page 94: Peripheral Devices
GS h FS q GS k ESC 2 GS ! GS r ESC 3 GS $ GS v 0 ESC = GS * GS w ESC ? GS ( A ESC @ GS ( K PA-3622 SERIES USER MANUAL Page: 4-9...
Page 95: Commands List
Print data in page mode Ignored <ESC SP> 1B 20 Set right-side character spacing <ESC !> 1B 21 Select print mode(s) <ESC $> 1B 24 Set absolute print position. <ESC *> 1B 2A Select bit image mode PA-3622 SERIES USER MANUAL Page: 4-10...
Page 96 1D 2A Define download bit images <GS ( A> 1D 28 41 Execute test print Disabled <GS ( K> 1D 28 4B Set print density Disabled <GS /> 1D 2F Print download bit image ● PA-3622 SERIES USER MANUAL Page: 4-11...
Page 97 <GS k> 1D 6B Print bar code ● <GS r> 1D 72 Transmit status <GS v 0> 1D 76 30 Print raster bit image ● Disabled <GS w> 1D 77 Set bar code width PA-3622 SERIES USER MANUAL Page: 4-12...
Page 98 ●: Enabled only when data is not present in the printer buffer. ▲: Only value setting is possible. Disabled: Parameters are processed as printable data. Ignored: All command codes including parameters are ignored and nothing is executed. PA-3622 SERIES USER MANUAL Page: 4-13...
Page 99  After execution, makes the top of the line the next print starting position. [Name] Print and recover to standard mode (in page mode) ASCII [Format] Hex. Decimal 12 [Range] Prints all buffered data to the print region collectively, then recovers to the standard [Description] mode. PA-3622 SERIES USER MANUAL Page: 4-14...
Page 100 Deletes all print data in the currently set print region in page mode.  This command is enabled only in page mode. [Description]  Portions included in the currently set print region are also deleted, even if previously set print region data. PA-3622 SERIES USER MANUAL Page: 4-15...
Page 101 No error. Error occurs. Not used. Fixed to Off. n = 3 : Error status On / Off Decimal Function Not used. Fixed to Off. Not used. Fixed to On. Not used. Fixed to Off. PA-3622 SERIES USER MANUAL Page: 4-16...
Page 102 = 1: Recover from the error and start printing from the line where the error [Description] occurred. n = 2: Recover from error after clearing the reception buffer and print buffer. This command is enabled even when the printer specification is disabled by ESC = (select peripheral devices). PA-3622 SERIES USER MANUAL Page: 4-17...
Page 103 [Format] Hex. Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 0 This command sets the size of space to right of character. [Description] Right space = n × [horizontal motion units]. PA-3622 SERIES USER MANUAL Page: 4-18...
Page 104 This command specifies the next print starting position in reference to the left edge of the print area. The printing start position is calculated using (nL + nH x [Description] 256) x (vertical or horizontal motion units). Specifications exceeding the print range are ignored. PA-3622 SERIES USER MANUAL Page: 4-19...
Page 105 67 DPI 101 DPI nL+nH×256 density 8 dot double 67 DPI 203 DPI nL+nH×256 density 24 dot (nL+nH×256) single 203 DPI 101 DPI ×3 density 24 dot (nL+nH×256) double 203 DPI 203 DPI ×3 density PA-3622 SERIES USER MANUAL Page: 4-20...
Page 106 Hex. Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 34 This command sets the line spacing using a following rule. [Description] Line spacing = n x (vertical or horizontal motion units) PA-3622 SERIES USER MANUAL Page: 4-21...
Page 107  n specifies the column number for setting a horizontal tab position from the [Description] left margin or the beginning of the line.  k indicates the number of horizontal tab positions to be set. PA-3622 SERIES USER MANUAL Page: 4-22...
Page 108  In page mode, this command functions as follows, depending on the starting position of the printable area: (1) When the starting position is set to the upper left or lower right of the printable area using ESC T, the vertical motion unit (y) is used. PA-3622 SERIES USER MANUAL Page: 4-23...
Page 109 FS q : Define NV bit image c. GS v 0 : Print raster bit images d. GS L : Set left margin  Recover to standard mode using ESC @ (initialize printer). PA-3622 SERIES USER MANUAL Page: 4-24...
Page 110 Initial Value n = 0 [Description] This command specifies international characters according to n values. Character Set France Germany Denmark I Sweden Italy Spain Japan Norway Denmark II Spain II Latin America Korea Russia Slavonic PA-3622 SERIES USER MANUAL Page: 4-25...
Page 111 GS $ :Specify absolute position for character vertical direction in page Mode GS \: :Specify relative position for character vertical direction in page mode  Standard mode is selected when the power is turned on, the printer is reset or initialized (ESC @). PA-3622 SERIES USER MANUAL Page: 4-26...
Page 112  Underlines are not applied to characters rotated 90 degrees clockwise even when ESC !,ESC - or FS - commands are given.  If 90 degree clockwise rotation is specified, double-wide and double-tall commands in the 90 rotation mode enlarges characters in the opposite PA-3622 SERIES USER MANUAL Page: 4-27...
Page 113 - horizontal starting position).  If (vertical starting position + printing area height) exceeds the printable area, the printing area height is automatically set to (vertical printable area [Description] - vertical starting position). PA-3622 SERIES USER MANUAL Page: 4-28...
Page 114 This command specifies position alignment for all data in one line in standard mode, using n as follows: Alignment Left alignment [Description] Center alignment Right alignment This command has no effect in page mode. PA-3622 SERIES USER MANUAL Page: 4-29...
Page 115 Selects the paper out detector to stop printing when paper has run out. Function “0” “1” Undefined Undefined Undefined [Description] Undefined Undefined Undefined Paper roll near end detector Invalid Valid Paper roll near end detector Invalid Valid PA-3622 SERIES USER MANUAL Page: 4-30...
Page 116 This command executes a full cut of the paper in standard mode ESC m [Name] Partial cut. ASCII [Format] Hex. Decimal [Range] This command executes a partial cut of the paper with one point uncut in [Description] standard mode. PA-3622 SERIES USER MANUAL Page: 4-31...
Page 117 Hex. Decimal 0 ≤ n ≤ 8 [Range] Initial Value n = 0 Select page n of the character code table. Character set CP-437 Katakana CP-850 [Description] CP-852 CP-860 CP-863 CP-865 CP-1252 User Define PA-3622 SERIES USER MANUAL Page: 4-32...
Page 118  NV bit image is a bit image defined in non-volatile memory by FS q and printed by this command.  This command is ignored when the specified NV bit image n is undefined. PA-3622 SERIES USER MANUAL Page: 4-33...
Page 119  xL and xH specify the horizontal direction for one NV bit image (xL + xH x 256) x 8 dots.  yL and yH specify the vertical direction for one NV bit image (yL + yH x 256) x 8 dots. PA-3622 SERIES USER MANUAL Page: 4-34...
Page 120 4 times 5 times 6 times 7 times 8 times Table 2 [Enlarged in vertical direction] Decimal Enlargement 1 time(standard) 2 times 3 times 4 times 5 times 6 times 7 times 8 times PA-3622 SERIES USER MANUAL Page: 4-35...
Page 121 [(nL + nH x 256) x basic [Description] calculated pitch] from the starting point.  When not in page mode, this command is ignored.  Specifications for absolute positions that exceed the specified print range are ignored. PA-3622 SERIES USER MANUAL Page: 4-36...
Page 122  Horizontal direction dot count is X x 8 dots; Vertical direction dot count is Y x 8 dots  d indicates the bit-image data. Bits that correspond to the dots to print are 1, and the bits that correspond to the dots that are not printed are 0. [Description] PA-3622 SERIES USER MANUAL Page: 4-37...
Page 123 Basic sheet (paper roll) [Description] 1 , 49 Paper Roll 2 , 50 m specifies a test pattern.. Type of Test Print 2 , 50 Printer Status (Self Print) 3 , 51 Rolling Pattern Print PA-3622 SERIES USER MANUAL Page: 4-38...
Page 124 This command prints the downloaded bit image defined by GS * according to the mode denoted by m. Vertical dot Horizontal dot Mode [Description] density(DPI) density(DPI) 0 , 48 Normal 1 , 49 Double-width 2 , 50 Double-height 3 , 51 Quadruple PA-3622 SERIES USER MANUAL Page: 4-39...
Page 125 Selects the printing position of HRI characters when printing bar codes. Printing Position 0, 48 No print [Description] 1, 49 Above bar code 2, 50 Below bar code 3, 51 Above and below bar code(both) PA-3622 SERIES USER MANUAL Page: 4-40...
Page 126 0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255 [Range] Initial Value (nL + nH x 256)=0 (nL=0, nH=0) nL and nH set the specified left margin. The left margin is [(nL + nH x 256) x basic calculated pitch]. [Description] PA-3622 SERIES USER MANUAL Page: 4-41...
Page 127 Feeds paper to (cutting position + [n x basic calculated pitch]) and performs a full cut Feeds paper to (cutting position + [n x basic calculated pitch]) and performs a partial cut (one point uncut) PA-3622 SERIES USER MANUAL Page: 4-42...
Page 128 [(nL + nH x 256) x basic calculated pitch] for the next data expanding starting position.  When not in page mode, this command is ignored. PA-3622 SERIES USER MANUAL Page: 4-43...
Page 129 Cover is open Not used. Fixed to On On-line Off-line Drawer kick-out connector pin 3 is LOW Drawer kick-out connector pin 3 is HIGH Not used. Fixed to Off Not used. Fixed to Off PA-3622 SERIES USER MANUAL Page: 4-44...
Page 130 Black mark sensor status Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On PA-3622 SERIES USER MANUAL Page: 4-45...
Page 131 Selects Font B (9 x 17). GS h n [Name] Set bar code height. [Format] ASCII Hex. Decimal 104 n [Range] 1 ≤ n ≤ 255 Initial Value n = 162 [Description] Sets bar code height to n dots. PA-3622 SERIES USER MANUAL Page: 4-46...
Page 132 48 ≤ d ≤ 57, 65 ≤ d ≤ 68, 36, 43, 45, 46, 47, 58 CODE93 1 ≤ n ≤ 255 0 ≤ d ≤ 127 CODE128 2 ≤ n ≤ 255 0 ≤ d ≤ 127 PA-3622 SERIES USER MANUAL Page: 4-47...
Page 133 Paper roll near end detector Has Paper Paper out [Description] Drawer Kick Connector Status (n=2,50) Status “0” “1” Fixed at 0 Undefined Undefined Fixed at 0 Undefined Undefined Undefined Drawer kick connector pin “L” “H” PA-3622 SERIES USER MANUAL Page: 4-48...
Page 134  xL and xH specify the horizontal direction data count for one bit image (xL + xH x 256) in bytes.  yL and yH specify the vertical direction data count for one bit image (yL + yH x 256) in bytes. [Description] PA-3622 SERIES USER MANUAL Page: 4-49...
Page 135 2 ≤ n ≤ 16 [Range] Initial Value n = 2 Specifies a module size of QR Code and Data Matrix. [Description] n: The number of dots for one side of the module size. PA-3622 SERIES USER MANUAL Page: 4-50...
Page 136 Mode Numerical mode Alphanumeric mode 8-bit byte mode Kanji mode Mixed mode nl, nh: Specifies the number of data. Data: Kanji data of the QR Code data should be set by Shift JIS code. PA-3622 SERIES USER MANUAL Page: 4-51...
Page 137 Batch specifies the Kanji character print mode. Function “0” “1” Underline Undefined Undefined Undefined Double tall expanded Expanded wide Undefined Undefined FS & [Name] Select Kanji character mode. ASCII & [Format] Hex. Decimal [Range] [Description] Specifies Kanji character mode. PA-3622 SERIES USER MANUAL Page: 4-52...
Page 138 Kanji character underlines. 2,50 Sets to two-dot width Kanji character underline and cancels Kanji character underlines. FS . [Name] Cancel Kanji character mode. ASCII [Format] Hex. Decimal [Range] [Description] Cancels Kanji character mode. PA-3622 SERIES USER MANUAL Page: 4-53...
Page 139 Specifies or cancels quadruple size Kanji character.  Cancels quadruple size when n = <*******0>B. [Description]  Specifies quadruple size when n = <*******1>B.  n is effective only when it is the lowest bit. PA-3622 SERIES USER MANUAL Page: 4-54...
Page 140: Opos Printer Driver
Follow the wizard instructions to complete the installation. • Launching the Program Follow the steps below to load the MB1030 program: Click the POSPrinter folder from the path: Start\Programs\Protech OPOS. • Click MB1030 to launch the program. • PA-3622 SERIES USER MANUAL...
Page 141 OPOS Control Object of MB1030 Program a.) Print tab buttons: Button/Item Description Printer Normal Print the string. b.) Bitmap tab buttons/items: Button/Item Description Load Load bitmap file. Print Bitmap Print bitmap file. Type Normal or Rotate 108˚. PA-3622 SERIES USER MANUAL Page: 4-56...
Page 142 Default Value Note BaudRate String 115200 UART Baud Rate (default) BitLength String UART Data Bit (default) Parity String UART Parity Bit (default) Port String COM4 UART Port (default) Stop String UART Stop Bit (default) PA-3622 SERIES USER MANUAL Page: 4-57...
Page 143 Not Applicable Properties specific long CapJrnDhigh Read only Not Applicable Properties specific long CapJrnDwide Read only Not Applicable Properties specific long CapJrnDwideDhigh Read only Not Applicable Properties specific long CapJrnEmptySensor Read only Not Applicable PA-3622 SERIES USER MANUAL Page: 4-58...
Page 144 CapSlpNearEndSensor Read only Not Applicable Properties specific bool CapSlpRight90 Read only Not Applicable Properties specific bool CapSlpRotate180 Read only Not Applicable Properties specific bool CapSlpUnderline Read only Not Applicable Properties specific bool AsyncMode Not Applicable PA-3622 SERIES USER MANUAL Page: 4-59...
Page 145 Properties specific bool JrnNearEnd Read only Not Applicable Properties specific long JrnCartridgeState Read only Not Applicable Properties specific long JrnCurrentCartridge Not Applicable Properties specific long RecLineChars Not Applicable Properties specific string RecLineCharsList Read only Not Applicable PA-3622 SERIES USER MANUAL Page: 4-60...
Page 146 Claim Supported Methods common ClaimDevice Supported Methods common Release Supported Methods common ReleaseDevice Supported Methods common CheckHealth Supported Methods common ClearInput Not Applicable Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable PA-3622 SERIES USER MANUAL Page: 4-61...
Page 147 Not Applicable Methods specific MarkFeed Not Applicable Events common DataEvent Not Applicable Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputComplete Not Applicable Event Events common StatusUpdate Not Applicable Event PA-3622 SERIES USER MANUAL Page: 4-62...
Page 148: Vfd: Mb-4103 (Rs-232)
Default Value MB4000_OPOS_SO.VFD.1 BaudRate 9600 BitLength Parity Port COM1 Stop chk_hw Version 1.14 Description Protech Systems LineDisplay OPOS Service Object OPOS VFD Service Object and Method Relations Method Status of Support Notes Open ○ Close ○ ClaimDevice ○ ReleaseDevice ○...
Page 149: Opos Driver
This setup also installs the MB4000_Opos_Test program. • Follow the onscreen wizard instructions to complete the installation. • Launching the Program The steps below guide you to load the MB4000_Opos_Test program: Click MB4000_Opos_Test to launch the program. • PA-3622 SERIES USER MANUAL Page: 4-64...
Page 150 Which Port is connected to VFD. Open Open OPOS Driver Claim Initial com port Release Un-initial com port Close Close OPOS Driver CheckHealth Check the status of service object Message screen: Button/Item Description Clear Clear the message PA-3622 SERIES USER MANUAL Page: 4-65...
Page 151 Scroll text Scroll the text at the current cursor position. • (ScrollText) Attribute LEFT: Scroll the text to move to the left. • RIGHT: Scroll the text to move to the right. • PA-3622 SERIES USER MANUAL Page: 4-66...
Page 152 Send the data to VFD Data Size Data length Text Area Type data on screen that will be send General of properties screen: Button/Item Description Device Brightness Set brightness for VFD Protech OPOS Driver Service Object Version PA-3622 SERIES USER MANUAL Page: 4-67...
Page 153 Window of properties screen: Item Description Rows Rows of VFD Columns Columns of VFD Character properties screen: Item Description GlyphHeight Height of character GlyphWidth Width of character Character Set Modify the codepage in VFD PA-3622 SERIES USER MANUAL Page: 4-68...
Page 154 Default Value Note BaudRate String 9600 UART Baud Rate (default) BitLength String UART Data Bit (default) Parity String UART Parity Bit (default) Port String COM1 UART Port (default) Stop String UART Stop Bit (default) PA-3622 SERIES USER MANUAL Page: 4-69...
Page 155 Read only Not Applicable Properties specific long CapReverse Read only Not Applicable Properties specific bool CapVMarquee Read only Not Applicable Properties specific long BlinkRate Not Applicable Properties specific long DeviceWindows Read only Not Applicable PA-3622 SERIES USER MANUAL Page: 4-70...
Page 156 ClearOutput Not Applicable Methods common DirectIO Not Applicable Methods specific DisplayText Supported Methods specific DisplayTextAt Supported Methods specific ClearText Supported Methods specific ScrollText Supported Methods specific SetDescriptor Not Applicable Methods specific ClearDescriptors Not Applicable PA-3622 SERIES USER MANUAL Page: 4-71...
Page 157: Opos Vfd Register
The OPOS VFD Register program sets up the registry information of VFD for OPOS program usage. Launching the Program The steps below guide you to load the VFD_Register program: VFD_Register to launch the program. • PA-3622 SERIES USER MANUAL Page: 4-72...
Page 158 Item Description Dev Name The VFD module name:MB4000 Which port do you want to connect device Bud Rate Baud rate: (1) 9600,N,8,1 (2) 19200,N,8,1 Flow Control CTS enable or None Check_Hw Enable or disable PA-3622 SERIES USER MANUAL Page: 4-73...
Page 159: Msr: Mb-3102 (Ps/2)
Follow the wizard instructions to complete the installation. • Launching the Program The steps below guide you to load the MB3012_Opos program. Click the MSR folder from the path: Start/Programs/Protech OPOS. • Click D04-3012-000-00-160311 to launch the program. • PA-3622 SERIES USER MANUAL...
Page 160 (only for UART/USB interface). AutoDisable (check box) Check to disable the device automatically when data is received. FreezeEvents (check box) Enable to trigger FreezeEvents, and the application will not allow events to be delivered. PA-3622 SERIES USER MANUAL Page: 4-75...
Page 161 Set decode data properties applicable. ParseDecodeData Set parse decode data properties TransmitSentinels Set transmit-sentinels properties ErrorReporting Type Card, track TracksToRead Track1, track2, track3, tracks12, tracks13, tracks14, tracks23, tracks24, tracks34, tracks123, tracks124, tracks134, tracks234, tracks1234 (Tracks4 is not applicable). PA-3622 SERIES USER MANUAL Page: 4-76...
Page 162 Chapter 4 Software Utilities d.) Track Data tab items Button/Item Description TracksData (Row) Display the data of all tracks (Track4 is not applicable). e.) Parsed Data tab items Button/Item Description Parsed Data Display special properties. PA-3622 SERIES USER MANUAL Page: 4-77...
Page 163 Properties specific bool CapTransmitSentinels Read only Supported Properties specific long TracksToRead Supported Properties specific bool DecodeData Not Applicable Properties specific bool ParseDecodeData Supported Properties specific long ErrorReportType Not Applicable Properties specific string Track1Data Read only Supported PA-3622 SERIES USER MANUAL Page: 4-78...
Page 164 Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable Events common DataEvent Supported Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputCompleteEvent Not Applicable Events common StatusUpdateEvent Not Applicable PA-3622 SERIES USER MANUAL Page: 4-79...
Page 165: Msr: Giga-Tms Mjr243 (Rs-232)
Device Name for CO open FileName (NULL) (reserved) HardwareProvider (reserved) Model MJR243 Device model name Parity None Parity for the communication port Port COM4 COM Port Protocol Hardware Communication Control Baudrate 19200 RS-232 baudrate PA-3622 SERIES USER MANUAL Page: 4-80...
Page 166 FirstName ○ Read only MiddleInitial ○ Read Only ParseDecodeData ○ ServiceCode ○ Read Only Suffix ○ Read Only Surname ○ Read Only Title ○ Read Only Track1Data ○ Read Only Track1DiscretionaryData ○ Read Only PA-3622 SERIES USER MANUAL Page: 4-81...
Page 167: Opos Msr Register
Launching the Program The steps below guides you how to load the OPOS MSR Register program. Click the OPOS folder from the path: Start/Programs/GIGA‐TMS. • Click OPOS MSR Register to launch the program. • PA-3622 SERIES USER MANUAL Page: 4-82...
Page 168 Chapter 4 Software Utilities PA-3622 SERIES USER MANUAL Page: 4-83...
Page 169 Step 1: Select an item in the Service Object List box from the left pane. Make sure the correct item is selected. Step 2: Click Reg button Step 3: In the OPOS MSR Setting screen, enter the device name and click PA-3622 SERIES USER MANUAL Page: 4-84...
Page 170 Chapter 4 Software Utilities c.) Example 1. MAGTEK USB HID d.) Example 2. PROMAG MSR/MJR PART‐NO, K eyboard mode. PA-3622 SERIES USER MANUAL Page: 4-85...
Page 171 Description for SO driver MSR POS DeviceName string MJR243 Device Name for CO open FileName string (NULL) (reserved) HardwareProvider string (reserved) Model string MJR243 Device model name Parity string None Parity for the communication port PA-3622 SERIES USER MANUAL Page: 4-86...
Page 172 Read only Supported string Properties specific bool CapISO Read only Supported Properties specific bool CapJISOne Read only Not Applicable Properties specific bool CapJISTwo Read only Not Applicable Properties specific bool CapTransmit Read only Supported PA-3622 SERIES USER MANUAL Page: 4-87...
Page 173 Methods common ReleaseDevice Supported Methods common CheckHealth Not Applicable Methods common ClearInput Supported Methods common ClearInput Supported Properties Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable Methods common Compare Not Applicable FirmwareVersion PA-3622 SERIES USER MANUAL Page: 4-88...
Page 174 Methods common UpdateFirmware Not Applicable Methods common UpdateStatistics Not Applicable Events common DataEvent Supported Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputCompleteEvent Not Applicable Events common StatusUpdateEvent Not Applicable PA-3622 SERIES USER MANUAL Page: 4-89...
Page 175: Opos Msr Tester
Launching the Program The steps below guide you to load the OPOS MSR Tester program. Click the OPOS folder from the path: Start\Programs\GIGA • ‐ TMS. Click OPOS MSR Tester to launch the program. • PA-3622 SERIES USER MANUAL Page: 4-90...
Page 176 To get the track data using OPOS driver, follow the steps below: Step 1: Enter the Device Name. Step 2: Click Open button. Step 3: Swipe the card to get the track data. PA-3622 SERIES USER MANUAL Page: 4-91...
Page 177 Chapter 4 Software Utilities c.) Example 1. MAGTEK USB HID. d.) Example 2. PROMAG MSR/MJR PART‐NO, Keyboard mode PA-3622 SERIES USER MANUAL Page: 4-92...
Page 178 Chapter 4 Software Utilities e.) Example 3. PROMAG MSR PART‐NO, HID mode PA-3622 SERIES USER MANUAL Page: 4-93...
Page 179: Api
Chapter 4 Software Utilities 4.9 API 4.9.1 API Package Content You can find the enclosed API Package files in the Protech Manual /Driver DVD. Depending on the machine types, the API Package may include the following files: Function DLL Directory...
Page 180: Api Procedure
Text1.text = “cash drawer1 close” ‘enter text into textbox. End if ‘========================================= Receive_Status2 = CashDrawerOpen(&H2) If Receive_Status2 = true then Text2.text = “cash drawer2 open” ‘enter text into textbox. Else Text2.text = “cash drawer2 close” ‘enter text into textbox. End if ‘========================================= PA-3622 SERIES USER MANUAL Page: 4-95...
Page 181 Public static extern bool GetCashDrawerStatus() [DllImport(“CashDrawer.dll”,EntryPoint = “CashDrawerOpen”)] Public static extern bool CashDrawerOpen(short num_drawer);} (2) Call Function Open cash drawer1 PortAccess.CashDrawerOpen(0x01); //check cash drawer1 status Open cash drawer2 PortAccess.CashDrawerOpen(0x02); //check cash drawer2 status Bool bstatus; bstatus = PortAccess.GetCashDrawerStatus(0x01); PA-3622 SERIES USER MANUAL Page: 4-96...
Page 182 As Boolean VB 6 external function: Declare Function CashDrawerOpen Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Declare Function GetCashDrawerStatus Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Note: VB.net short = integer VB6 PA-3622 SERIES USER MANUAL Page: 4-97...
Page 183: Cash Drawer
Cash Drawer Status Cash drawer status will be displayed after OPEN is tapped. Cash Drawer is closed when the following picture is • shown: Cash Drawer is opened when the following picture is • shown: PA-3622 SERIES USER MANUAL Page: 4-98...
Page 184: Watchdog
• START: Tap to start the watchdog timer. Meanwhile, the REFRESH and STOP buttons will be enabled. • STOP: Tap to stop the watchdog timer. • REFRESH: Tap to restart the watchdog timer. PA-3622 SERIES USER MANUAL Page: 4-99...
Page 185 = 1 (Get the Cash Drawer1 status) num_drawer = 2 (Get the Cash Drawer2 status) Return: True (1) on success, False (0) on failure Example: Short data; data= GetCashDrawerStatus(0x01); // Get the Cash Drawer1 status PA-3622 SERIES USER MANUAL Page: 4-100...
Page 186 Stop the watchdog timer Value None Return: True (1) on success, False (0) on failure Watchdog_Recount bool Watchdog_Recount (void); Purpose: Restart the watchdog timer Value None Return: True (1) on success, False (0) on failure PA-3622 SERIES USER MANUAL Page: 4-101...
Page 187 The BIOS Setup Utilities consist of the following menu items: Accessing Setup Utilities • Main Menu • Advanced Menu • Chipset Menu • Security Menu • Boot Menu • Save & Exit Menu • PA-3622 SERIES USER MANUAL Page: 5-1...
Page 188 Chapter 5 BIOS Setup 5.1 Introduction The PA-3622 System uses an AMI (American Megatrends Incorporated) Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the built-in BIOS setup program, Power-On Self-Test (POST), PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
Page 189 All the menu settings are described in details in this chapter. 5.2 Accessing Setup Utility After the system is powered on, BIOS will enter the Power-On Self-Test (POST) routines and the POST message will be displayed: PA-3622 SERIES USER MANUAL Page: 5-3...
Page 190 Chapter 5 BIOS Setup Figure 5-2. POST Screen with AMI Logo Press <Del> or <Esc> to access the Setup Utility program and the Main menu of the Aptio Setup Utility will appear on the screen as below: PA-3622 SERIES USER MANUAL Page: 5-4...
Page 191 US English. You may use <↑> or <↓> key to select among the items and press <Enter> to confirm and enter the sub-menu. The following table provides the list of the navigation keys that you can use while operating the BIOS setup menu. PA-3622 SERIES USER MANUAL Page: 5-5...
Page 192 Load the previous configuration values. <F3> Load the default configuration values. <F4> Save the current values and exit the BIOS setup menu. <Esc> Close the sub-menu. Trigger the confirmation to exit BIOS setup menu. PA-3622 SERIES USER MANUAL Page: 5-6...
Page 193 Displays the date that the current BIOS Time version is built. Sec RC Version No changeable options Displays the current Sec RC version. TXE FW Version No changeable options Displays the current TXE Version PA-3622 SERIES USER MANUAL Page: 5-7...
Page 194 The “Day” is automatically changed. System Time Hour, minute, second Sets the system time. The format is [Hour: Minute: Second]. Users can directly enter values or use <+> or <-> arrow keys to increase/decrease it. PA-3622 SERIES USER MANUAL Page: 5-8...
Page 195 CPU Configuration Sub-Menu CPU Configuration. Parameters. IDE Configuration Sub-Menu SATA Configuration Parameters. OS Selection Sub-Menu OS Selection Configures Option ROM execution, boot CSM Configuration Sub-Menu options filters, etc. USB Configuration Sub-Menu USB Configuration Parameters. PA-3622 SERIES USER MANUAL Page: 5-9...
Page 196 Configuration and Power Management Interface) settings, such as Enable Hibernation. ACPI Settings Screen BIOS Setting Options Description/Purpose Enable - Disabled Enables or Disables System ability to Hibernation - Enabled Hibernate (OS/S4 Sleep State). This option may be not effective with some PA-3622 SERIES USER MANUAL Page: 5-10...
Page 197 Sets the parameters of Serial Port 4 Serial Port 4 Configuration Sub-menu (COMD). Sets Parameters of Parallel Port Parallel Port Configuration Sub-menu ( LPT/LPTE). - Cash Drawer 12V Cash drawer Cash Drawer select 12V or 24V. - Cash Drawer 24V PA-3622 SERIES USER MANUAL Page: 5-11...
Page 198 - IO=3F8h; IRQ=4; settings for the Serial Port 1. - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; COM1 Voltage - Disabled Disables or selects COM1 select - 12V Voltage 12V/5V. - 5V PA-3622 SERIES USER MANUAL Page: 5-12...
Page 199 Serial Port 2. Change Settings - Auto Selects IRQ and I/O resource - IO=2F8h; IRQ=3; settings for the Serial Port 2. - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-3622 SERIES USER MANUAL Page: 5-13...
Page 200 Serial Port 3. Change Settings - Auto Selects IRQ and I/O resource - IO=3E8h; IRQ=7; settings for the Serial Port 3. - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F0h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12; PA-3622 SERIES USER MANUAL Page: 5-14...
Page 201 - IO=2E8h; IRQ=10; settings for the Serial Port 4. - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F0h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12; - Disabled Disables or selects COM4 COM4 Voltage - 12V Voltage 12V/5V. select - 5V PA-3622 SERIES USER MANUAL Page: 5-15...
Page 202 Changes the printer port - SPP Mode mode. - EPP-1.9 and SPP Mode Device Mode - EPP-1.7 and SPP Mode - ECP Mode - ECP and EPP 1.9 Mode - ECP and EPP 1.7 Mode PA-3622 SERIES USER MANUAL Page: 5-16...
Page 203 No changeable options Detects and displays 12V voltage. VCC3V No changeable options Detects and displays 3V voltage. VSB3V No changeable options Detects and displays VSB3V voltage. Detects and displays the battery VBAT No changeable options voltage. PA-3622 SERIES USER MANUAL Page: 5-17...
Page 204 Selects 1s (second) or 60s (minute) as Watchdog timer unit - 60s the time unit of Watchdog timer. Count for Timer Numeric (from 1 to Sets the timeout for Watchdog timer. (Seconds) 255) (Max. value: 255 seconds or minutes) PA-3622 SERIES USER MANUAL Page: 5-18...
Page 205 BIOS Setting Options Description/Purpose Socket 0 Sub-Menu Reports CPU Information CPU Information CPU Speed No changeable options Displays the CPU speed. Reports if the processor supports Intel 64-bit No changeable options x86-64 (amd64) implementation. PA-3622 SERIES USER MANUAL Page: 5-19...
Page 206 Intel HT Technology No changeable options Reports if Intel Hyper-Threading Technology is supported by processor. Hyper Threading is Intel’s term for its simultaneous multithreading implementation in their CPUs. Enable this function will improve parallelization of PA-3622 SERIES USER MANUAL Page: 5-20...
Page 207 L1 Code Cache No changeable options Displays the size of L1 Code Cache. L2 Cache No changeable options Displays the size of L2 Cache. L3 Cache No changeable options Displays the size of L3 Cache. PA-3622 SERIES USER MANUAL Page: 5-21...
Page 208 SATA Speed Support - GEN2 Gen2 mode sets the device to 3 Gbit/s speed (in case it is compatible). - Port0 ODD SATA ODD Port SATA ODD is Port0 or Port1 - Port1 ODD PA-3622 SERIES USER MANUAL Page: 5-22...
Page 209 SATA Port 0 [drive] SATA port 0. Shows [Empty] if no drive is installed. Displays the drive installed on the SATA Port 1 [drive] SATA port 1. Shows [Empty] if no drive is installed. PA-3622 SERIES USER MANUAL Page: 5-23...
Page 210 The OS Selection allows users to select the operating system from Windows 7 or Windows 8.x &10. OS Selection Screen BIOS Setting Options Description/Purpose - Windows 7 OS Selection OS Selection - Windows 8.x & 10 PA-3622 SERIES USER MANUAL Page: 5-24...
Page 211 ALWAYS: Do not allow disabling • GA20; this option is useful when any RT code is executed above 1MB. Option ROM - Force BIOS Configures the display mode for Option Messages - Keep Current ROM messages. PA-3622 SERIES USER MANUAL Page: 5-25...
Page 212 Controls the execution of UEFI and Video - UEFI Legacy Video. - Legacy - Do not launch Selects launch method for other PCI Other PCI devices - UEFI devices, such as NIC, mass storage or - Legacy video card. PA-3622 SERIES USER MANUAL Page: 5-26...
Page 213 USB Mass Storage Driver - Disabled Enable/Disable USB mass storage driver Support - Enabled support. The time-out value for Control, Bulk, and USB transfer time-out 1 / 5 / 10 /20 sec Interrupt transfers. PA-3622 SERIES USER MANUAL Page: 5-27...
Page 214 Delay range is from 1 to 40 seconds, in ranging from 0 to seconds one second increments 5.5 Chipset Menu Path Chipset This menu allows users to configure advanced Chipset settings such as North Bridge and South Bridge configuration parameters. Chipset Screen PA-3622 SERIES USER MANUAL Page: 5-28...
Page 215 Displays the DRAM information on Memory Information No changeable options the platform. Total Memory No changeable options Displays the DRAM size Memory Slot0 No changeable options Memory in the slot 0. PA-3622 SERIES USER MANUAL Page: 5-29...
Page 216 The LCD Control allows users to select the primary and secondary display device. LCD Control Screen BIOS Setting Options Description/Purpose Primary IGFX Boot - CRT Select Primary Display Device Display - LVDS - Disabled Secondary IGFX - CRT Select Secondary Display Device Boot Display - LVDS PA-3622 SERIES USER MANUAL Page: 5-30...
Page 217 • Power On keeps the system powered on after the system restores AC power to the board. • Last State brings the system back to the last power state when the AC power is removed. PA-3622 SERIES USER MANUAL Page: 5-31...
Page 218 Setup utility. Security Screen BIOS Setting Options Description/Purpose Password can be 3-20 Specifies the administrator Administrator Password alphanumeric characters. password. Password can be 3-20 User Password Specifies the user password. alphanumeric characters. PA-3622 SERIES USER MANUAL Page: 5-32...
Page 219 Specifies the power-on state of the Bootup NumLock State - Off NumLock Key. - Disabled Enable or Disable Quiet Boot Quiet Boot - Enabled Options - Disabled Fast Boot Enable or Disable Fast Boot Options - Enabled PA-3622 SERIES USER MANUAL Page: 5-33...
Page 220 Select Hard Drive BBS Priorities from the Boot menu to configure the boot order and priority of the available drives. Hard Drive BBS Priorities Screen BIOS Setting Options Description/Purpose - [Drive(s)] Set the system boot order for hard Boot Option #1~#n - Enabled driver. PA-3622 SERIES USER MANUAL Page: 5-34...
Page 221 Discard Changes and Reset to discard any changes you have made and restore the factory BIOS defaults. Load User Defaults You may simply press F3 at any time to load the Optimized Values which resets all BIOS settings to the factory defaults. Save & Exit Screen PA-3622 SERIES USER MANUAL Page: 5-35...
Page 222 Save the changes done so far as User Save as User Defaults No changeable options Defaults. Restore the User Defaults to all the Restore User Defaults No changeable options setup options. Forces to boot from selected Boot Override - [Drive(s)] [drive(s)]. PA-3622 SERIES USER MANUAL Page: 5-36...
Page 223 Appendix A System Diagrams This appendix presents the exploded diagrams of the system as well as the part numbers of the PA-3622 system.  Exploded Diagram for System Top Case  Exploded Diagram for LCD Module With Touch  Exploded Diagram for System ...
Page 224 Appendix A System Diagrams Exploded Diagram For System Top Case Open the System Top Module Page: A-2 PA-3622 SERIES USER MANUAL...
Page 225 Appendix A System Diagrams Component Name P/N No. Q’ty Remark PA-3222-Bot Unit PA-3222_VFD Unit M3_L4_I_B 22-272-30004318 PA-3222_Top_Unit M6 Stand 22-289-60035007 Rubber Foot (S1608) 30-004-01500000 Mini_Pcie_Door 30-007-28110165 PA-3100_Side_Door 30-007-28210165 PA-3100_Printer_Unit PS-3100_I/O_Cable_Cover 30-002-28110165 MSR & Fingerprint & ibutton PA-3622 SERIES USER MANUAL Page: A-3...
Page 226 PAN HEAD SCREW T3.0x6mm 22-132-30060011 ROUND HEAD SCREW 22-230-30005811 M3x0.5Px5mm FILLISTER HEAD SCREW 22-272-30012011 M3x0.5Px12mm FLAT HEAD SCREW #2 / 22-112-30006311 T3.0x6mm FILLISTER HEAD SCREW #1 / 22-272-20004011 M2 x 0.4Px4mm CABLE_COVER_RUBBER 30-002-01100210 TOUCH_PANEL 52-380-16583701 52-351-15156702 Page: A-4 PA-3622 SERIES USER MANUAL...
Page 227 Appendix A System Diagrams System Exploded Diagram PA-3622 SERIES USER MANUAL Page: A-5...
Page 228 22-252-30017001 Open Bushing (SA-1013A) 30-026-04300000 PA-3211_Speaker 13-500-08280318 PA-3222_com_cable 27-024-40003031 No.4_UNC_H5_L7_BOSS 22-692-40048051 PA-3222_2nd_PWR_Cable 27-012-21703071 M2.5_L4_R_Ni 22-232-25004011 SB-0305 30-026-04100008 PA-3222_Rj11-Cable 27-026-16505111 RJ11 Holder 80-029-03002165 wireless_antenna 27-029-16506071 roller_pin 22-092-29039001 roller 30-041-04100165 BOSS_M3-H12_L6 22-258-30012051 ground_cable 27-030-16504071 fan_hole_pc_sheet 90-056-02100254 Page: A-6 PA-3622 SERIES USER MANUAL...
Page 229 Appendix A System Diagrams Exploded Diagram For HDD Component Name P/N No. Q’ty 2inch_SATA_HDD See Order PA-3222 HDD Holder 80-029-03001400 Sata Cable 27-012-33903081 M3_L5_W_Ni 22-242-30005311 PA-3622 SERIES USER MANUAL Page: A-7...
Page 230 MSR TOP COVER 30-014-12420210 MSR TOP COVER SIDE 30-002-12122210 I BUTTON I BUTTON NUT MSR BRACKET 20-006-03061210 MSR MODULE MSR FIX BRACKET 20-006-03003210 M6_L6_F_B 22-232-30060211 MSR BTM COVER 30-002-12020210 M3 TAPPING SCREW 20-006-03003210 M3 screw 22-232-30060211 Page: A-8 PA-3622 SERIES USER MANUAL...
Page 231 Appendix A System Diagrams Fingerprint Module Exploded Diagram Component Name P/N No. Q’ty FINGERPRINT BTM COVER 30-002-12220210 FINGERPRINT TOP COVER 30-002-12120210 T3 FLAT HEAD SCREW 22-712-30010011 FINGERPRINT MODULE FINGERPRINT BKT 20-006-03002210 T3 FLAT HEAD SCREW 22-712-30010011 PA-3622 SERIES USER MANUAL Page: A-9...
Page 232 SII 3” Thermal Printer (Base 52-701-05017003 Side) M2_L4_I_Ni 22-272-20004011 EMI_GASKET_20x5x0.5 90-050-31200165 See Next ps3100_paper_cover_Unit Page M3_L5_W_Ni 22-242-30005311 paper_cover_pin 20-004-10011165 ps3100_spring-1 23-002-00000701 pg-13-270p 30-022-09110000 printer_add_arm 30-002-09110165 M3_L4_I_B 22-272-30004318 printer_power_cable 27-012-16502071 PA-3222_printer_cable (USB) 27-006-40307111 MB-1011RB-11N MB-1011RB-11N printer_pcb_cover 20-004-03001165 M2.5_L4_R_Ni 22-232-25004011 Page: A-10 PA-3622 SERIES USER MANUAL...
Page 233 3-Inch Printer Component Name P/N No. Q’ty Remark paper_holder2.sldprt 30-012-02110165 T2_L8_R_B 22-125-20008011 ps3100_paper_cover_v2 30-002-02530165 include_holder 20-029-03006165 ps3100_printer_cover_ejector 30-002-09210165 ps3100-spring-for_ejector 23-002-00001021 M3_L4_I_B 22-272-30004318 T3_L6_PAN_NI 22-132-30060011 3100_printer_eva 90-013-15200165 3inch_add_mylar 90-056-02600165 3” Thermal Printer (Cut Side) T3_L8_R_B 22-122-30080011 PA-3622 SERIES USER MANUAL Page: A-11...
Page 234 Side) EMI_GASKET_20x5x0.5 90-050-31200165 M2_L4_I_Ni 22-272-20004011 See Next ps3100_paper_cover_Unit Page M3_L5_W_Ni 22-242-30005311 paper_cover_pin 20-004-10011165 ps3100-spring-1 23-002-00000701 pg-13-270p 30-022-09110000 printer_add_arm 30-002-09110165 M3_L4_I_B 22-272-30004318 add_paper_wall 30-002-28310165 printer_power_cable 27-012-16502071 PA-3222_printer_cable (USB) 27-006-40307111 MB-1011RB-11N MB-1011RB-11N printer_pcb_cover 20-004-03001165 M2.5_L4_R_Ni 22-232-25004011 Page: A-12 PA-3622 SERIES USER MANUAL...
Page 235 2-Inch Printer Component Name P/N No. Q’ty Remark paper_holder2.sldprt 30-012-02110165 T2_L8_R_B 22-125-20008011 ps3100_paper_cover_v2 30-002-02530165 include_holder 20-029-03006165 ps3100_printer_cover_ejector 30-002-09210165 ps3100-spring-for_ejector 23-002-00001021 M3_L4_I_B 22-272-30004318 T3_L6_PAN_NI 22-132-30060011 3100_printer_eva 90-013-15200165 2inch_add_mylar2 90-056-02300165 2” Thermal Printer (Cut Side) T3_L8_R_B 22-122-30080011 PA-3622 SERIES USER MANUAL Page: A-13...
Page 236 Appendix A System Diagrams VFD Module Exploded Diagram Component Name P/N No. Q’ty Remark ps3100_vfd_cover 30-002-28114165 ps3100_vfd_window 30-002-02230165 VFD_Model MB-4103RA-11N PORON_135x4x0.5 90-013-24100165 PA-3222_VFD_CABLE 27-053-23805111 Page: A-14 PA-3622 SERIES USER MANUAL...
Page 237 This appendix will give you a brief introduction of the allocation maps for the system resources. The following topics are included: • Interrupt Map • DMA Channels Map • I/O Map • Memory Map • Configuring WatchDog Timer • Flash BIOS Update PA-3622 SERIES USER MANUAL Page: B-1...
Page 238 IRQ 93 Microsoft ACPI-Compliant System IRQ 94 Microsoft ACPI-Compliant System IRQ 95 Microsoft ACPI-Compliant System IRQ 96 Microsoft ACPI-Compliant System IRQ 97 Microsoft ACPI-Compliant System IRQ 98 Microsoft ACPI-Compliant System IRQ 99 Microsoft ACPI-Compliant System Page: B-2 PA-3622 SERIES USER MANUAL...
Page 239 IRQ 134 Microsoft ACPI-Compliant System IRQ 135 Microsoft ACPI-Compliant System IRQ 136 Microsoft ACPI-Compliant System IRQ 137 Microsoft ACPI-Compliant System IRQ 138 Microsoft ACPI-Compliant System IRQ 139 Microsoft ACPI-Compliant System IRQ 140 Microsoft ACPI-Compliant System Page: B-3 PA-3622 SERIES USER MANUAL...
Page 240 IRQ 175 Microsoft ACPI-Compliant System IRQ 176 Microsoft ACPI-Compliant System IRQ 177 Microsoft ACPI-Compliant System IRQ 178 Microsoft ACPI-Compliant System IRQ 179 Microsoft ACPI-Compliant System IRQ 180 Microsoft ACPI-Compliant System IRQ 181 Microsoft ACPI-Compliant System Page: B-4 PA-3622 SERIES USER MANUAL...
Page 241 Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 Note: These resource information were gathered using Windows 7 (the IRQ could be assigned differently depending on OS) DMA MAP ASSIGNMENT Channel 3 Printer Port (LPT1) Page: B-5 PA-3622 SERIES USER MANUAL...
Page 242 Motherboard resources 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000002E8-0x000002EF Communications Port (COM4) 0x000002F8-0x000002FF Communications Port (COM2) 0x00000378-0x0000037F Printer Port (LPT1) 0x000003B0-0x000003BB Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 Page: B-6 PA-3622 SERIES USER MANUAL...
Page 243 Processor AHCI - 0F23 0x0000F050-0x0000F057 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F060-0x0000F063 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F070-0x0000F077 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F080-0x0000F087 Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0x00000000-0x0000006F PCI bus Page: B-7 PA-3622 SERIES USER MANUAL...
Page 244 0F12 0xD0500000-0xD05FFFFF Intel(R) Trusted Execution Engine Interface 0xD0400000-0xD04FFFFF Intel(R) Trusted Execution Engine Interface 0xA0000-0xBFFFF Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xA0000-0xBFFFF PCI bus 0xC0000-0xDFFFF PCI bus 0xE0000-0xFFFFF PCI bus 0xD0600000-0xD06FFFFF Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Page: B-8 PA-3622 SERIES USER MANUAL...
Page 245 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xC0000000-0xCFFFFFFF Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xC0000000-0xCFFFFFFF PCI bus 0xFED00000-0xFED003FF High precision event timer 0xD0604000-0xD0604FFF Realtek PCIe GBE Family Controller 0xD0700000-0xD070FFFF Intel(R) USB 3.0 eXtensible Host Controller Page: B-9 PA-3622 SERIES USER MANUAL...
Page 246 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. Page: B-10 PA-3622 SERIES USER MANUAL...
Page 247 ; ----------------------- Select Logical Device 7 of watchdog timer --------------------- dx, al dx, al ;---------------------------------Enable Watch dog feature ------------------------------ 030h dx, al dx, al ;------------------------------- Enable Watch PME-------------------------------------------- 0FAh dx, al dx, al ;-------------------------- Set second as counting unit -------------------------------------- 0F5h dx, al Page: B-11 PA-3622 SERIES USER MANUAL...
Page 248 Appendix B Technical Summary dx, al ; ---------------- Set timeout interval as 30seconds and start counting -------------- 0F6h dx, al dx, al ;---------------------------------Exit the extended function mode ------------------------- 0AAh dx, al Page: B-12 PA-3622 SERIES USER MANUAL...
Page 249 (4) Select [Boot] menu. (5) Select [Hard Drive BBS Priorities] and set the USB bootable device as the 1st boot device. (6) Press F4 to save the configuration and exit the BIOS setup menu. Page: B-13 PA-3622 SERIES USER MANUAL...
Page 250 Appendix B Technical Summary Page: B-14 PA-3622 SERIES USER MANUAL...
Page 251 BIOS ROM may be crashed and the system will be unable to boot up next time. After the BIOS update procedure is completed, the following messages will be shown: Page: B-15 PA-3622 SERIES USER MANUAL...
Page 252 5. Restart the system and boot up with the new BIOS configurations. 6. The BIOS Update is completed after the system is restarted. 7. Reboot the system and verify if the BIOS version shown on the initialization screen has been updated. Page: B-16 PA-3622 SERIES USER MANUAL...

protech PA-3622 User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for protech PA-3622

Summary of Contents for protech PA-3622

Table of Contents