Related Manuals for Premier Mounts FTP
Summary of Contents for Premier Mounts FTP
- Page 1 Fine Tune Projector Mount Model: FTP / FTPW INSTALLATION INSTRUCTIONS premiermounts.com | p. 800.368.9700 | e. orders@premiermounts.com 500 W Central Ave, Suite A, Brea, CA 92821 USA 9530-090-001-0C...
-
Page 2: Table Of Contents
EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED... -
Page 3: Installation Tools
Ladder Tape Measure Socket Wrench Extension Wood Drill Bit Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. Fine Tune Projector Mount Hardware FTP Dome (Qty 1) Universal Projector Plate With Four Pre-installed Legs... -
Page 4: Mounting Hardware
Mounting Hardware Lock-It™ Security Hardware Pack Your Premier Mounts Fine Tune Projector Mount comes with the option of using Lock-It™ Security Screws. Simply replace any of the Phillips head screws with the corresponding sized Lock-It™ Security Screws and tighten using the appropriate size Allen wrench. -
Page 5: Features
Projector Direction Arrows Inscribed on the underside of the FTP Dome and on the top of the Quick Set Base, you can always know for certain which way your projector will be pointing while you are installing your Fine-Tune Projector mount. -
Page 6: Installing The Fine Tune Projector Mount
Installing the Fine Tune Projector Mount Introduction adapter, or a single ceiling stud. If using an optional Premier Mounts adapter, please refer to the installation instructions that come with each adapter on the proper installation of that product. Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product. - Page 7 Remove the Installation Disk and store it in a safe location. Step 4 Secure the FTP Dome to the pipe with one (1) M6 x 6mm set screw and tighten it using the M3 Allen wrench. You can use either the standard hardware or Lock-It™...
-
Page 8: Wood Stud Installation
Fine Tune Projector Mount Installing the Fine Tune Projector Mount (cont’d) Wood Stud Installation Step 1 desired installation location. 2) Identify the center of the ceiling stud. 3) Use a pencil to mark the location of the ceiling stud center. Be sure to only install on ceiling with a max drywall thickness of 5/8”. - Page 9 1) Insert one (1) #14 x 3˝ screw through each of the holes in the bottom of the Installation Disk and into the pilot holes. 2) Tighten each screw until the FTP Dome and Installation Disk are secure against the ceiling.
-
Page 10: Attaching The Universal Projector Plate
Fine Tune Projector Mount Attaching the Universal Projector Plate Selecting the Mounting Hardware 1) Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector. 2) Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. -
Page 11: Multiple Mount Point Installation
Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Multiple Mount Point Installation Step 1 1) Locate the projector’s mount points. 2) Position an appropriate number of mounting legs on the projector. use three (3) or four (4) long and/or short mounting legs depending on what your projector requires. - Page 12 Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Step 3 Raise or lower each of the mounting legs, by rotating the leveling barrels, until all of the mounting legs are at an equal height. • Lower the mounting leg by rotating the leveling barrel counter-clockwise.
-
Page 13: Single Mount Point Installation
Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Step 6 Tighten the mounting screws to the projector. Do not overtighten the mounting screws. Step 7 1) Attach the Universal Projector Plate (if not already attached) to each of the mounting legs by inserting and tightening one (1) M6 x 12mm screw through the Universal Projector Plate into the M6 square nut on each of the mounting legs. -
Page 14: Securing The Quick Set Base
Attaching the Projector to the Mount If your projector is heavy and/or bulky, two people may be required to safely attach your projector to the FTP Dome. If your projector is to be mounted higher than shoulder height, you may need to use one or more ladders to safely attach your projector to the FTP Dome. -
Page 15: Alignment & Fine-Tuning
Fine Tune Projector Mount Alignment & Fine-Tuning Yaw can be adjusted up to 20° ° right from center. Adjust the projector’s yaw by turning control ...clockwise to pivot the front to the right..counter-clockwise to pivot the front Each full revolution of the control adjusts the yaw by 4°. -
Page 16: Locking In The Adjustments
Locking in the Adjustments FTP Support Sphere you can lock them in to prevent them from being accidentally changed. with the FTP Support Sphere (Figure 1). factory setting which you should not change (Figure 2). Figure 1 Figure 2 Securing the Fine Tune Projector Mount deterrence for your projector. - Page 17 12.12 [308] 4.76 [121] 3.28 [83] 4.05 [103] © PREMIER MOUNTS 500 W Central Ave, Suite A Brea, CA 92821 USA & CANADA Phone: 800-368-9700 Fax: 800-832-4888 e. orders@premiermounts.com Installation Instructions Page 17 premiermounts.com | p. 800.368.9700 | e. orders@premiermounts.com...
Need help?
Do you have a question about the FTP and is the answer not in the manual?
Questions and answers