Transporting The Appliance - Krups XS 4000 Manual

PRODUCT INFORMATION
Coffee cycles Displays the total number of coffees produced by the machine.
Water cycles Displays the total number of hot water cycles carried out by the machine.
Cappuccino cycles Displays the total number of cappuccino cycles carried out by the machine.
Rinsing Displays the total number of rinsing operations carried out by the machine.
Coffee cleaning
PRODUCT
INFORMATION
Displays the total number of cappuccino cleaning operations carried out by
Cappuccino cleaning
the machine.
Descaling
Filter
*: The first two options in the Filter sub-menu will not be confirmed unless you have correctly installed a filter
previously, with the programme accessible via MAINTENANCE ► FILTER ► INSTALL.

TRANSPORTING THE APPLIANCE

Keep and use the original packaging to transport the appliance.
If the appliance is dropped while not in its packaging, it is recommended that you take it to an approved repair centre to avoid
any risk of fire or electrical problems.
END-OF-LIFE ELECTRIC OR ELECTRONIC PRODUCTS
Think of the environment!
Your appliance contains many materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
28
Displays the number of coffees carried out since the last
Last
cleaning operation.
Displays the number of coffees that can be produced
Next
before the next cleaning operation.
Clean Starts the cleaning programme.
Exit Takes you back to the previous menu.
Displays the total number of hot water or steam cycles
Last
made since last scale removal.
Displays the number of hot water or steam operations that
Next
can be carried out before the next descaling operation.
Exit Takes you back to the previous menu.
Displays the date of the last filter change* and the
Last
quantity of water used.
Displays the date for the next filter change* and the
Next
quantity of water to run through.
Install Starts the filter replacement procedure.
Exit Takes you back to the previous menu.
problem malfunction corrective actions
Turn off and unplug the machine, remove the filter cartridge, wait for
The appliance does not switch on when the
20 seconds and then restart the machine. Ensure that the plug on the
ON/OFF button is pressed.
electrical cable is fully inserted into the power socket.
In the case of repeated uses, a few drops may issue from the steam
Water or steam issue from the steam nozzle.
nozzle.
Change the coffee temperature setting. Heat the cups by rinsing under hot
The espresso or coffee is not hot enough.
water.
Check that the coffee bean container holds coffee and that this is flowing
correctly.
Avoid using oily, caramelised or flavoured coffee beans.
The coffee is too lightly coloured or too weak. Reduce the volume of coffee using the central button.
Turn the grinding fineness button to the left to obtain more finely ground
coffee.
Carry out your preparation over two cycles by using the two-cup function.
Turn the grinding fineness button to the right to obtain more coarsely
ground coffee (may depend on the type of coffee used).
The coffee is poured too slowly or not at all.
Carry out one or more rinsing cycles.
Run a damp sponge beneath the coffee outlet.
Turn the grinding fineness button to the left to obtain more finely ground
coffee (may depend on the type of coffee used).
The coffee is not creamy. Change the Claris - Aqua Filter System cartridge (follow the installation
procedure on page 3).
Carry out one or more rinsing cycles.
An incident has been detected during preparation.
The appliance has not produced coffee.
The appliance has automatically restarted and is ready for a new cycle.
You have used ground coffee instead of coffee Use your vacuum cleaner to remove the pre-ground coffee from the coffee
beans. bean container.
There are foreign bodies present in the grinder. Contact the KRUPS
The coffee grinder makes a strange noise.
Customer Service team.
Only modify the grinding fineness setting when it is in operation. There
The grinding fineness setting button is difficult
are foreign bodies present in the grinder: contact the KRUPS Customer
to turn.
Service team.
Disassemble the nozzle using the dismantling key. Fig. 44
Start the cappuccino system rinsing cycle to remove the remainder of the
The steam nozzle of your cappuccino system deposits.
seems partially or completely clogged. Clean the steam nozzle and ensure that the opening of the nozzle is not
obstructed by remains of milk or limescale. Use the cleaning needle if
necessary.
Check that the appliance is correctly assembled.
Ensure that the setting button is in the CAPPUCCINO position.
Ensure that the steam nozzle is not blocked.
Ensure that the air nozzle is in place and correctly assembled. Ensure that
the flexible pipe is not blocked or twisted and that it is properly inserted
The cappuccino system does not suck the milk. into the cassette to avoid any air leak.
The cappuccino system makes little or no froth. Ensure the milk suction pipe is fully immersed in the milk.
Rinse and clean the system (see corresponding sections).
For milk-based preparations: we recommend that you use very fresh, very
cold pasteurised or UHT milk, recently opened. Unpasteurised milk does
not produce the best results. It is also recommended that you use a cold
container.
After having washed the cleaning drawer, the Remove the drawer, wait for six seconds, then replace it. Ensure the
warning message is still displayed on the screen. cleaning drawer is fully inserted.
The appliance will automatically restart when the power returns, and will
A power failure occurs during a cycle. be ready for a new cycle. If the power failure occurs during a cleaning or
descaling cycle, the machine will continue the cycle at the current stage.
29