Download Print this page

Advertisement

Quick Links

LFV 60
EN
Operator's manual
2-19

Advertisement

loading

Summary of Contents for Husqvarna LFV 60

  • Page 1 LFV 60 Operator's manual 2-19...
  • Page 2: Table Of Contents

    Contents Introduction..............2 Transportation, storage and disposal......14 Safety................3 Technical data.............. 16 Operation................ 8 Declaration of Conformity..........18 Maintenance..............11 Introduction Product description Intended use The product is a walk-behind forward plate compactor The product is for professional operation only. Use the with a combustion engine.
  • Page 3: Safety

    11. Engine ON/OFF switch Noise emission to the environment as 12. Starter rope handle referred to in the EC directive. The 13. Choke control emission of the product is specified in Technical data on page 16 and on the 14. Air filter label.
  • Page 4 Safety instructions for operation if the instructions in the manual are not obeyed. WARNING: Read the warning CAUTION: instructions that follow before you use the Used if there is a risk of product. damage to the product, other materials or the adjacent area if the instructions in the •...
  • Page 5 operation of the product can cause or increase the the source where possible. Make sure that the degree of injuries to the operator. Injuries can occur equipment is correctly installed and used and that in fingers, hands, wrists, arms, shoulders, and/or regular maintenance is done.
  • Page 6 Do a check of the safety devices regularly. If the correctly installed. safety devices are damaged or do not operate • Examine the vibration damping units for damages correctly, speak to your Husqvarna service agent. and wear. • Do not make modifications to safety devices. •...
  • Page 7 • Do not fill fuel in an indoor area. Insufficient airflow Safety instructions for operation near edges can cause injury or death because of asphyxiation or carbon monoxide poisoning. WARNING: Read the warning • Do not smoke near the fuel or the engine. instructions that follow before you use the •...
  • Page 8: Operation

    Operation Introduction 2. Set the throttle control to ⅓ throttle. WARNING: Read and understand the safety chapter before you use the product. To do before you operate the product • Read the operator's manual carefully and make sure that you understand the instructions. •...
  • Page 9 4. Set the engine ON/OFF switch to "ON". 8. Open the choke control gradually until it is fully open. 5. Pull the starter rope handle slowly until you feel resistance. 9. Let the engine operate at idle speed for 2–3 minutes. 10.
  • Page 10 To stop the product 3. Close the fuel valve. 1. Set the throttle control to the idle speed position. To operate the product 2. Set the engine ON/OFF switch to "OFF". The engine CAUTION: Always operate the product stops. forward and at full throttle. Lower engine speed and rearward movement prevents correct function of the eccentric element and can cause product failure.
  • Page 11: Maintenance

    a) To turn the product with a minimum turning radius, lift the handle to a 90 degrees angle. Use this function in small spaces and on ground that is not level. Maintenance Introduction Maintenance schedule * = General maintenance done by the operator. The WARNING: Read and understand the instructions are not given in this operator's manual.
  • Page 12 Engine maintenance Before use, After the Weekly, Yearly, each each 10 h first 20 h each 100 h 300 h Clean the cooling fins of the engine. Examine the air filter. Clean the air filter if it is necessary. Clean the air filter. Replace the air filter.
  • Page 13 2. Remove the oil drain plug (A) and connect a hose 3. Remove the foam filter element (E) and the paper (B). filter element (D). 3. Tilt the product and let the oil run out into the container. 4. Remove the hose. 4.
  • Page 14: Transportation, Storage And Disposal

    3. Examine the V-belt for damages and wear. Replace the V-belt if it is necessary. WARNING: Be careful when you 4. Examine the tension of the V-belt. replace the belt. There is a risk of injury. 5. If the tension is not sufficient, do these steps: 1.
  • Page 15 Discard all chemicals, such as engine oil or fuel, at a service center or at an applicable disposal location. • When the product is no longer in use, send it to a Husqvarna dealer or discard it at a recycling location. 2128 - 001 - 30.06.2023...
  • Page 16: Technical Data

    Technical data Technical data Net weight, kg/lb 63/138.9 Operation weight (EN500, incl. oil, ½ fuel), kg/lb 64/141.1 Engine brand, type Honda GX120 Engine power, kW/hp @rpm 2.4 kW/3.2 hp @ 3600 rpm Vibration frequency, Hz/rpm 95/5700 Amplitude, mm/in. 0.905/0.04 Centrifugal force, N/lbf 10.4/2.34 Operation speed, m/min or ft./min 22 or 72...
  • Page 17 Noise and vibration declaration values are not suitable for use in risk assessments and values measured in individual work places may statement be higher. The actual exposure values and risk of harm experienced by an individual user are unique and These declared values were obtained by laboratory depend upon the way the user works, in what material type testing in accordance with the stated directive or...
  • Page 18: Declaration Of Conformity

    Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Forward Plate Compaction Machine Brand Husqvarna Type/Model LFV 60 Identification Serial numbers dating from 2023 and onwards...
  • Page 19 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Forward Plate Compaction Machine Brand Husqvarna Type/Model LFV 60 Identification Serial numbers dating from 2023 and onwards complies fully with the following UK regulations:...
  • Page 20 www.husqvarnaconstruction.com Original instructions 1143742-26 2023-07-10...