Table of Contents
Advertisement
Available languages
Available languages
Display
Grease Filter Saturation Alarm
After 30 hours of fan function, the display will show "Clean
Grease Filter" when the fan is active. When this icon shows in
the display, the installed grease filters should be washed. See
the "Range Hood Care" section.
To reset the grease filter saturation alarm, press and hold the
■
Power Increase button for 5 seconds. The "Clean Grease
Filter" icon will no longer be displayed.
Charcoal Filter Saturation Alarm
After 120 hours of fan function, the display will show "Replace
Charcoal Filter" when the fan is active. When this icon shows
in the display, the charcoal filters should be replaced. See the
"Range Hood Care" section.
To reset the charcoal filter saturation alarm, press and hold
■
the Power Decrease button for 5 seconds. The "Replace
Charcoal Filter" icon will no longer be displayed.
Audible Signal Activation and Deactivation
The audible signals can be activated or deactivated by pressing
the Light button for 5 seconds.
If the audible signal is activated, a tone will sound and "Snd"
■
symbol will appear in the display for 3 seconds.
If the audible signal is deactivated, the "Snd" symbol will
■
appear on the display for 3 seconds.
Charcoal Filter (Recirculation Accessory) Inclusion
and Exclusion
When the charcoal filter is in use (recirculating mode), press
and hold the Power Decrease and Power Increase buttons at
the same time for 5 seconds. "Able" will appear in the display
for 3 seconds.
If the charcoal filter is not used (vented mode), press and hold
the Power Decrease and Power Increase buttons at the same
time for 5 seconds. "None" will appear in the display for 3
seconds.
When the charcoal filter has been excluded, the charcoal
■
filter alarm is disabled.
The inclusion or exclusion of the charcoal filter must be
■
selected while the lights and the fan motor are Off.
Heat Sensor
The control is equipped with a heat sensor that will turn on the
blower to the highest speed if excessive heat occurs around the
control area.
If the blower is On or Off, the blower will automatically set
■
to the highest speed. "Auto" will appear in the display to
indicate that the heat sensor has detected excessive heat.
When the blower is operating due to excessive heat detected
■
by the heat sensor, the blower speed cannot be decreased.
When the temperature level on the hood drops to
■
normal, the blower will return to its setting before the
excessive heat was sensed.
12
To operate the light:
1. Press the Light button to turn the lights On.
2. Press the Light button again to turn the lights Off.
The timer can be set from 1 to 60 minutes. The default timer
setting is 10 minutes.
To use the timer:
1. Press the Timer button to enter the timer mode. After 5
seconds the default time will be automatically selected.
2. Press the Power Decrease and Power Increase buttons
while the display is flashing (5 seconds) to adjust to the
desired time. Pressing the timer button again or waiting
5 seconds after selecting the desired time will start the
timer countdown.
3. The timer can be canceled at any time by pressing
the Timer button again.
NOTE: During the timer setup, the Power Decrease and Power
Increase buttons are dedicated to the timer. After the timer
starts, the Power Decrease and Power Increase buttons can be
used for other functions.
Fan Speed
Power Increase/On
This button is used to turn the fan On or increase the fan speed.
The fan will turn On if the Power Increase button is
■
pressed and the hood was Off.
An audible tone will sound when the fan reaches its
■
highest speed.
Power Decrease/Off
This button is used to turn the fan Off or to decrease the fan
■
speed.
Timed Fan Off
The control has a "Timed Fan Off" feature. When activated, it
automatically turns the blower fan off after 10 minutes.
Press and hold the Timer button for 5 seconds to activate.
■
The fan icon will flash and 10:00 (10 minutes) will show in the
display. The time will start counting down after 3 seconds.
Light
Timer
Advertisement
Table of Contents
