Craftmade Inspo INS54 Installation Manual

Hide thumbs Also See for Inspo INS54:

Installation manual (30 pages)

Table of Contents

Quick Links

Download this manual

Inspo

Installation Guide

For Models:

INS54

INS62

APPROVED FOR

INDOOR USE ONLY

APPROVED FOR

WET LOCATION ONLY

net weight of fan: 17.86 lb (8.1 kg), INS54

19.07 lb (8.65 kg), INS62

Models:

INS54

INS62BNK3

Models:

INS62FB3

INS62W3

READ THESE INSTRUCTIONS AND

AND SAVE THEM FOR FUTURE USE

Need help?

Do you have a question about the Inspo INS54 and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade Inspo INS54

Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Inspo Installation Guide For Models: INS54 INS62 Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly.
Page 2: Safety Tips
8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. Distributed by: Craftmade, 3901 S. 20 Avenue, DFW Airport, TX, 75261; 1-800-486-4892 NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur.
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.
Page 4: Installation Preparation
3. Installation Preparation. blade edge 7 feet inches To prevent personal injury and damage, ensure (2.13 m) (76 cm) that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. 12ft.
Page 5: Fan Assembly. Pgs
stop pin set screw 5. Fan Assembly. hanging ball Remove hanging ball from downrod provided by loosening set screw on hanging ball. Lower hanging ball and remove stop pin and then slide hanging ball diagram 1 off of the downrod. [Refer to diagram 1.] safety cable Loosen yoke set screws and nut at top of motor electrical wiring...
Page 6: Wiring. Pgs
wood ceiling 5. Fan Assembly. (cont.) joist safety cable loop With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the wood screw hanging bracket.
Page 7: Canopy Assembly
6. Wiring. (cont.) Modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. IN ORDER TO WIRE WALL CONTROL, *NOTE: This equipment has been tested and found to comply with the limits for a Class B remove existing wall switch.
Page 8: Blade Assembly
8. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power motor tools to assemble the blades. If screws are housing overtightened, blades may crack and break. blade Locate 3 blade plates and 9 blade attachment screws/washers in hardware packs.
Page 9: Wall Control Operation
10. Wall Control Operation. - turns fan to LOW speed - turns fan to MEDIUM speed - turns fan to MEDIUM-HIGH speed - turns fan to HIGH speed - turns fan OFF 11. Testing Your Fan. It is recommended that you test fan before reverse switch finalizing installation.
Page 10: Troubleshooting
Troubleshooting. Warranty. CRAFTMADE LIMITED LIFETIME WARRANTY: WARNING: Failure to disconnect power supply CRAFTMADE warrants this fan for use as intended under prior to troubleshooting any wiring issues may the following provision: CRAFTMADE will replace any result in serious injury. fan which has faulty performance due to a defect in material or workmanship or fails to operate satisfactorily Problem: Fan fails to operate.

This manual is also suitable for:

Inspo ins62