Table of Contents
Advertisement
Quick Links
d-Color MF654/MF554/MF454
© Olivetti S.p.A
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
1. Outline of installation procedures
PC-115
AU-102
AU-201S
FS-533*
PK-519*
When installing the main body and associated options as a system, follow the order shown on the upper.
Caution:
• Lifting the main body in an awkward position or transporting it in a poorly balanced position could result in
personal injury. When transporting the main body, assign an adequate number of persons to the job and
ensure that each person can take a good position of not being excessively loaded.
(mass: approx. 110 kg (242-1/2 lb))
Note:
• For the detailed installation procedures for each option, follow the instructions given in the corresponding
installation manual and perform the procedures correctly.
• When placing the main body on the floor, make sure to use the paper feed cabinet or the desk to secure
the performance and the quality of the product.
• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.
Y118120-9
INSTALLATION MANUAL
HT-509
TK-101
PC-215
PC-415
KP-101
Machine
KH-102
SP-501
UK-501
Electronic system options
MK-735
WT-506
CU-102
2
FK-515*
3
3
JS-506*
OT-506
3
FS-536
FS-536SD
PK-520
Applied Machines: d-Color MF654/MF554/MF454
MK-734
DK-510
DK-705
MK-730
Electronic system options
LU-207
EK-609*
LU-302
2
MK-742*
RU-513
FS-537
FS-537SD
ZU-609
PI-507
JS-602
PK-523
E-1
1
EK-608*
1
HD-524*
1
1
UK-212*
1
SC-508*
FK-514
IC-416
VI-510
*1
: No particular order in
installation procedures.
*2
: Varies depending on the
applicable marketing area
*3
: MF554/MF454 only
Installation Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Olivetti d-Color MF554
Summary of Contents for Olivetti d-Color MF554
- Page 1 MF654/MF554/MF454 INSTALLATION MANUAL © Olivetti S.p.A Applied Machines: d-Color MF654/MF554/MF454 <Important> Be sure to correctly follow the procedures in order as explained in this Installation Manual. If you do not follow the procedure in order, the image trouble may occur.
- Page 2 2. Installation space (unit: mm (inch)) 4. Notes on using touch panel d-Color MF654 + PC-215 + FS-537SD + LU-207 Be sure to instruct users on the following points. • This machine uses a capacitive touch panel. 2477 (97-1/2) When you touch the touch panel, use your fin- 1244 ger or the stylus pen supplied with the machine.
- Page 3 Note: 6. Installing the main body and the Paper • Keep the paper size label at hand. It is neces- Feed Cabinet (or the Desk) sary for mounting the Large Capacity Unit LU- 302. (1) Take the main body and the Paper Feed Cabinet •...
-
Page 4: Removing Protective Tape, Packing And Other Shipping Materials
7. Removing protective tape, packing and (2) Open the right door and remove the protective sheet and locking materials. other shipping materials Note: (1) Remove the protective tape and the protective • After removing the locking materials, make sure materials. that the transfer roller assy is secured in place. - Page 5 (6) Slide out the tray 2 and remove the tray locking (10) Remove the protective sheets. materials. (11) Open the lower front door. (7) Remove the protective tapes from the inside of the tray 2 and remove accessory parts. (12) Remove the protective tape. (8) Remove the locking screws.
- Page 6 (13) Remove the protective tape from the develop- (16) Slightly slide the drum unit (K) out and remove ing units. the protective tape. Note: Do not remove the tape A in this procedure. (17) Slide the drum unit (K) into the machine. (18) Lock the drum unit (K) with the lever.
-
Page 7: Installing The Toner Cartridge
8. Installing the toner cartridge (4) Push the toner cartridge all the way in and rotate it clockwise to lock it. Note: Note: Since cartridge is not supplied with the machine, Make sure that the toner cartridge is pushed all the purchase toner cartridge (of different colors) sepa- way in. -
Page 8: Connecting The Power Cord
(2) Set the stylus pen in the place shown in the illus- 11. Connecting the power cord tration. Note: Steps (1) and (2) may be unnecessary depending on the applicable marketing area. (1) Connect the power cord. Use the appropriate power cord. Failure to do this could result in a fire or electrical shock. -
Page 9: Starting The Machine
12. Starting the machine 15. Unit change Open the lower front door and turn ON the power Note: switch, then close the lower front door. This function allows the user to select the type of message that will appear when the replacement time arrives for each of the different units. -
Page 10: Configuring Other Options
17. Configuring other options (3) Route the network cable. <When adding no paper feed options/desk or when (1) If any of the following options are installed, refer using the Desk DK-705> to the “Configuration procedures” of the installa- a) Route the network cable through the harness tion manual for each option and configure the guide and pass it through the notch. -
Page 11: Network Setting
c) Route the network cable through the harness 19. Network setting guide and three wire saddles. Make the TCP/IP address setting for the network. Note: Note: Leave an appropriate amount of slack in the por- Consult the network administrator for the setting tion of the cable between the plug and the harness value to be entered and make settings as guide in a manner which does not interfere with... -
Page 12: Affixing The Paper Size Label
23. Changing the stopper position 24. Affixing the paper size label Remove the stopper from the hinge of the reverse Affix the paper size labels that correspond to the automatic document feeder. (One screw each for sizes of paper used in each tray. right and left) Change the set position of the stopper to the upper side and secure it in position. -
Page 13: Accessory Parts
OT-506 Output Tray INSTALLATION MANUAL 1. Accessory parts 2. Installation procedures (1) Check whether the output tray has the snap-fit Name Shape Q’ty hook illustrated below or not. 1. Output tray < With the snap-fit hook > 2. Output guide <... - Page 14 (2) Open the upper and lower front door of the (5) Install the output tray. machine. <With the snap-fit hook> (3) Remove the upper left cover from the machine. (Three screws) <Without the snap-fit hook> (4) Attach the supplied output guide to the machine. ②...
- Page 15 SP-501 Stamp Unit INSTALLATION MANUAL 1. Accessory parts 2. Installation procedures (1) Turn OFF the power switch and unplug the Name Shape Q’ty power cord from the power outlet. 1. Stamp unit (2) Remove the stopper from the hinge of the reverse automatic document feeder.
- Page 16 (3) Open the reverse automatic document feeder, (7) Remove the rear cover. then remove the six screws. (8) Remove the screw, then remove the pin. (4) Close the reverse automatic document feeder. (Front: at two places; rear: at one place) (5) Remove the front cover.
- Page 17 (10) Remove the stamp unit cover. (One screw) (13) Install the stamp unit and the ground terminal. (One screw removed in step (11)) Note: Tighten the unit together with the ground terminal. Ground terminal Stamp unit (11) Remove the ground terminal. (One screw) (14) Connect the stamp unit connector to the main Ground terminal body relay connector.
-
Page 18: Configuration Procedures
(17) Remove the stopper from the hinge of the reverse automatic document feeder. (One screw each for right and left) Change the set position of the stopper to the upper side and secure it in position. 3. Configuration procedures (1) Plug the power cord into the power outlet and turn ON the power switch.
Need help?
Do you have a question about the d-Color MF554 and is the answer not in the manual?
Questions and answers