Download Print this page
Linear Technology DC1763A Demo Manual

Linear Technology DC1763A Demo Manual

Hide thumbs Also See for DC1763A:

Advertisement

Quick Links

Description
Demonstration circuit 1763A supports a family of 16-Bit
20Msps to 125Msps ADCs. Each assembly features one
of the following devices:
LTC2192, LTC2191, LTC2190,
ADCs.
The versions of the 1763A demo board are listed in Table 1.
Depending on the required resolution and sample rate,
Table 1. DC1763A Variants
DC1763A VARIANTS
1763A-A
1763A-B
1763A-C
1763A-D
1763A-E
1763A-F
1763A-G
perForMAnce sUMMArY
PARAMETER
Supply Voltage – DC1763A
Analog Input Range
Logic Input Voltages
Logic Output Voltages (Differential)
Sampling Frequency (Convert Clock Frequency)
Encode Clock Level
Resolution
Input Frequency Range
SFDR
SNR
Arrow.com.
Downloaded from
LTC2192, LTC2191, LTC2190, LTC2271
16-Bit, 20Msps to 125Msps Dual ADCs
LTC
2195, LTC2194, LTC2193,
®
LTC2271
high speed, dual
ADC PART NUMBER
LTC2195
LTC2194
LTC2193
LTC2192
LTC2191
LTC2190
LTC2271
(T
= 25°C)
A
CONDITIONS
Depending on Sampling Rate and the A/D Converter
Provided, this Supply Must Provide up to 500mA.
Depending on SENSE Pin Voltage
Minimum Logic High
Maximum Logic Low
Nominal Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
Minimum Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
Single-Ended Encode Mode (ENC
Differential Encode Mode (ENC
DEMO MANUAL DC1763A
LTC2195, LTC2194, LTC2193,
the DC1763A is supplied with the appropriate ADC. The
circuitry on the analog inputs is optimized for analog input
frequencies from 5MHz to 140MHz. Refer to the data sheet
for proper input networks for different input frequencies.
Design files for this circuit board are available at
http://www.linear.com/demo/DC1763A
L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks
and PScope is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
RESOLUTION
MAXIMUM SAMPLE RATE
16-Bit
125Msps
16-Bit
105Msps
16-Bit
16-Bit
16-Bit
16-Bit
16-Bit
Tied to GND)
Not Tied to GND)
INPUT FREQUENCY
5MHz to 140MHz
5MHz to 140MHz
80Msps
5MHz to 140MHz
65Msps
5MHz to 140MHz
40Msps
5MHz to 140MHz
25Msps
5MHz to 140MHz
20Msps
5MHz to 140MHz
MIN
TYP
MAX
3
3.6
1
1.3
0.6
350
1.25
247
1.25
See Table 1
0
3.6
0.2
3.6
See Table 1
See Table 1
See Applicable Data Sheet
See Applicable Data Sheet
UNITS
6
V
2
V
P-P
V
V
mV
V
mV
V
V
V
dc1763afb
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the DC1763A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Linear Technology DC1763A

  • Page 1 Depending on the required resolution and sample rate, L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks and PScope is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners.
  • Page 2: Quick Start Procedure

    SHDN) If a DC1371 PStache Data Acquisition and Collection JP2: WP: Enable/Disables write protect for the EEPROM. System was supplied with the DC1763A demonstration (Default: EN) circuit, follow the DC1371 Quick Start Guide to install the JP14/JP8: LANE/TERM: Two bits that select between required software and for connecting the DC1371 to the one, two and four lanes.
  • Page 3 ETC1-1-13 (lead free part number MABA007159-000000). Demonstration Circuit Encode Clock If a DC1371 is used to acquire data from the DC1763A, the NOTE: Apply an encode clock to the SMA connector on DC1371 must FIRST be connected to a powered USB port the DC1763A demonstration circuit board marked J12 and have 5V applied BEFORE applying 3.0V to 6V across...
  • Page 4 Digital Outputs The data outputs, data clock, and frame clock signals are available on J1 of the DC1763A. This connector follows the VITA-57/FMC standard, but all signals should be verified Figure 2. PScope Toolbar when using an FMC carrier card other than the DC1371.
  • Page 5 DEMO MANUAL DC1763A qUick stArt proceDUre This menu allows any of the options available for the Output Current: Selects the LVDS output drive current LTC2195 family to be programmed serially. The LTC2195 • 1.75mA (Default): LVDS output driver current family has the following options: • 2.1mA: LVDS output driver current Randomizer: Enables data output randomizer • 2.5mA: LVDS output driver current...
  • Page 6: Parts List

    DEMO MANUAL DC1763A pArts list ITEM REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER General BOM CAP , ARRAY, 0508 2.2µF 20% 4V X5R AVX, W2L14D225MAT1A C5, C7, C8, C9, C15, C16, C18, C28, CAP ., X5R, 0.1µF , 10V, 10% 0402 AVX, 0402ZD104KAT2A C36, C48, C52 CAP ., X5R, 1µF , 10V, 10% 0402...
  • Page 7 DEMO MANUAL DC1763A pArts list ITEM REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER DC1763A-A GENERAL BOM DC1763A C2, C3 CAP ., X5R, 0.1µF , 10V, 10% 0402 AVX, 0402ZD104KAT2A C25, C26, C33, C34 CAP ., X7R, 0.01µF , 50V, 10% 0603 AVX, 06035C103KAT2A C27, C35 CAP , COG, 4.7pF , 50V, 5% 0402...
  • Page 8: Schematic Diagram

    DEMO MANUAL DC1763A scheMAtic DiAgrAM dc1763afb Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from...
  • Page 9 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
  • Page 10 Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods.