Download Print this page

Linear Technology DC1762A Demo Manual

Hide thumbs Also See for DC1762A:

Advertisement

Quick Links

Description
Demonstration circuit 1762A supports a family of 16-Bit
20Msps to 125Msps ADCs. Each assembly features one
of the following devices: LTC
LTC2162, LTC2161, LTC2160, LTC2159, or LTC2269 high
speed, high dynamic range ADCs.
Demonstration circuit 1762A supports the LTC2165 family
DDR LVDS output mode.
The versions of the 1762A demo board supporting the
LTC2165 series of A/D converters are listed in Table 1.
Table 1. DC1762A Variants
DC1762A VARIANTS
1762A-A
1762A-B
1762A-C
1762A-D
1762A-E
1762A-F
1762A-G
1762A-H
performance summary
PARAMETER
Supply Voltage – DC1762A
Analog Input Range
Logic Input Voltages
Logic Output Voltages (Differential)
Sampling Frequency (Convert Clock Frequency)
Convert Clock Level
Resolution
Input Frequency Range
SFDR
SNR
Arrow.com.
Downloaded from
LTC2162, LTC2161, LTC2160, LTC2159, LTC2269
2165, LTC2164, LTC2163,
®
ADC PART NUMBER
LTC2165
LTC2164
LTC2163
LTC2162
LTC2161
LTC2160
LTC2159
LTC2269
(T
CONDITIONS
Depending on Sampling Rate and the A/D Converter
Provided, this Supply Must Provide up to 500mA.
Depending on SENSE Pin Voltage
Minimum Logic High
Maximum Logic Low
Nominal Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
Minimum Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
See Table 1
Single-Ended Encode Mode (ENC
Differential Encode Mode (ENC
See Table 1
See Table 1
See Applicable Data Sheet
See Applicable Data Sheet
DEMO MANUAL DC1762A
LTC2165, LTC2164, LTC2163
16-Bit, 20Msps to125Msps ADCs
Depending on the required resolution and sample rate,
the DC1762A is supplied with the appropriate ADC. The
circuitry on the analog inputs is optimized for analog input
frequencies from 5MHz to 140MHz. Refer to the data sheet
for proper input networks for different input frequencies.
Design files for this circuit board are available at
http://www.linear.com/demo
L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks
and PScope is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
RESOLUTION
MAXIMUM SAMPLE RATE
16-Bit
16-Bit
16-Bit
16-Bit
16-Bit
16-Bit
16-Bit
16-Bit
= 25°C)
A
Tied to GND)
Not Tied to GND)
INPUT FREQUENCY
125Msps
5MHz to 140MHz
105Msps
5MHz to 140MHz
80Msps
5MHz to 140MHz
65Msps
5MHz to 140MHz
40Msps
5MHz to 140MHz
25Msps
5MHz to 140MHz
20Msps
5MHz to 140MHz
20Msps
5MHz to 140MHz
MIN
TYP
MAX
4.5
1
1.3
0.6
350
1.25
247
1.25
0
0.2
UNITS
6
V
2
V
P-P
V
V
mV
V
mV
V
3.6
V
3.6
V
dc1762afb
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the DC1762A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Linear Technology DC1762A

  • Page 1 DDR LVDS output mode. http://www.linear.com/demo L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks The versions of the 1762A demo board supporting the and PScope is a trademark of Linear Technology Corporation. All other trademarks are the LTC2165 series of A/D converters are listed in Table 1.
  • Page 2: Quick Start Procedure

    JP3 Duty Cycle Stabilizer: enables/disables duty cycle Quick Start Guide to install the required software and for stabilizer. (default: enable) connecting the DC890 to the DC1762A and to a PC. JP4 SHDN: Enables and disables the LTC2165. (default: enable) JP5 NAP: Enables and disables NAP mode. (default:...
  • Page 3 SNR. In the noise power of the signals. In the case of the DC1762A a case of the DC1762A, a bandpass filter used for the clock bandpass filter used for the clock should be used prior to should be used prior to the DC1075 clock divider board.
  • Page 4 Check the Config Manually box and use the following Serial Programming configuration options, see Figure 2. PScope has the ability to program the DC1762A board Manual Configuration settings: serially through the DC890. There are several options available in the LTC2165 family that are only available Bits: 16 through serially programming.
  • Page 5 DEMO MANUAL DC1762A Quick start proceDure Clock Inversion: Selects the polarity of the CLKOUT signal: • Normal (Default): Normal CLKOUT polarity • Inverted: CLKOUT polarity is inverted Clock Delay: Selects the phase delay of the CLKOUT signal: • None (Default): No CLKOUT delay • 45 deg: CLKOUT delayed by 45 degrees • 90 deg: CLKOUT delayed by 90 degrees • 135 deg: CLKOUT delayed by 135 degrees Clock Duty Cycle: Enables or disables duty cycle stabilizer • Stabilizer off (Default): Duty cycle stabilizer disabled...
  • Page 6 Randomizer: Enables Data Output Randomizer • Double CMOS: Double data rate CMOS output mode • Off (Default): Disables data output randomizer (This mode is not supported by the DC1762A) • On: Enables data output randomizer Test Pattern: Selects digital output test patterns Two’s complement: Enables two’s complement mode • Off (Default): ADC data presented at output • Off (Default): Selects offset binary mode...
  • Page 7: Parts List

    DEMO MANUAL DC1762A parts List ITEM REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER Required Circuit Components Capacitor, Array, 0508, 2.2µF , 20%, 10V, X5R AVX W2L14D225MAT1A C1, R28, R32, R47, R48, R53, R54 Resistor, 0402, 0Ω, Jumper Vishay CRCW04020000Z0ED C2, C3, C6, C7, C8, C59, C60 Capacitor, 0402, 0.01µF , 10%, 16V, X7R...
  • Page 8 DEMO MANUAL DC1762A parts List ITEM REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER XFMR, 1:1 Macom MABA-007159-000000 XFMR, 1:1 CT M/A-C0M MABAES0060 T2 - Alternate XFMR, 1:1 CT Coilcraft WBC1-1LB XFMR, 1:1 Macom MABA-007159-000000 IC, EEPROM Microchip Tech. 24LC025-I/ST Refer to Schematic Table...
  • Page 9: Schematic Diagram

    Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
  • Page 10 Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods.