Welcome... Welcome to the User's Guide for the DECT phone Aastra 610d for Aastra 400 commu- nication systems. This User's Guide will assist you with the use of your phone and introduce you step by step to the functions and configurations.
Do not expose your device to electromagnetic fields (electric motors, household appli- ances). The speech quality could be affected. To prevent interference, avoid placing your handset in the immediate vicinity of computers, radios, TV sets, VCRs, and other tele- phone sets. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• Store the batteries at room temperature. Above-average temperatures tend to reduce the service life of batteries. To dispose of the battery packs Do not throw away the batteries with your domestic waste. Take the batteries to an appropriate collection point for recycling. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Purpose and function This product is part of the Aastra 400 communication solution. Aastra 400 is an open, modular and comprehensive communication solution for the business sector with several communication servers of different performance and expansion capacity, an extensive telephone portfolio and a multitude of expansions.
Page 10
ISO 9001 quality guidelines. The relevant user information has been compiled with the utmost care. The functions of the Aastra 400 products have been tested and approved after comprehensive con- formity tests. Nonetheless, errors cannot be entirely excluded. The manufacturers shall not be liable for any direct or indirect damage that may be caused by incorrect handling, improper use, or any other faulty behaviour.
North America, Europe and Africa as well as Internet Service Providers and distributors of renown. Aastra Technologies Limited, (TSX: “AAH”), is a leading company at the forefront of the enterprise communication market. Aastra has its headquarters in Concord, Ontario, Canada.
Exclusions Aastra does not warrant its products to be compatible with the equipment of any par- ticular telephone company. This warranty does not extend to damage to products resulting from improper installation or operation, alteration, accident, neglect, abuse, misuse, fire or natural causes such as storms or floods, after the product is in your pos- session.
Page 13
Part 5-4 of Schedule 2 to the Competition and Consumer Act 2010 (the ACL), the exer- cise of a right conferred by such a provision or any liability of Aastra in relation to a failure to comply with a guarantee that applies under Division 1 of Part 3-2 of the ACL to a supply of goods or services.
Page 14
Aastra in relation to a failure to comply with a guarantee that applies under Division 1 of Part 3-2 of the ACL to a supply of goods or services.
In the state... Description Loudspeaker LED indicator 3 colours LED as per Table in chapter "Indicator LED signals", page Display LC display (monochrome) Side keys + / - short In a connection Adjusting the volume Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 18
• Menu • Scrolling back through the menu • Navigate cursor • Editor • Lists Call key short • Idle state • Call up redial list • Lists • Dial select call number Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 19
Idle state, Editor * input long Idle state, for Activate/deactivate ring tone incoming call Hash key short Idle state, Editor # input long Idle state Locking the keypad Headset connec- tion Microphone Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• Information on operating times can be found in the chapter "Battery", page 109. System registrations Phone registered in system A, B, C, or D and ready for use (only displayed when phone is registered on more than one system) Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 22
Operating and display elements Status information About Warning Not permitted Phone book Name Private phone number Business phone number Mobile phone number Presence state Available (default) Absent Meeting Busy Not available Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• To find out how to make phone calls with the headset, refer to the chapter "Using a headset", page 27. • To find out how to activate the automatic hands-free mode, refer to the chapter "Using your phone in hands-free mode", page 26. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Press the Call key. ➔ Redial list is displayed. To scroll through the call numbers last dialled, press the navigation key down- wards. Press the Call key. ➔ The phone number displayed is dialled. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 26
You can switch the microphone on and off during a call. Switching the microphone off: Micro Press the Micro softkey. ➔ The microphone is deactivated, is displayed. Micro Switching the microphone back on: Press the Micro softkey once again. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 27
88. • To call a user, select the user’s phone number and press the Call key or Loud- speaker key. • For more information refer to your headset’s user’s guide. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
You can also store phone numbers and functions on a softkey (see chapter "Configur- keys", page 100) <Function> Press the softkey where the function you want is displayed on top of the screen. <long> Keep the softkey held down for a moment (about 2 seconds). Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
The digit keys are used to enter the digits 0 to 9. Enter letters You can also use the digit keys to enter letters and special characters. A number of let- ters and special characters are assigned to each key. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 31
You want to go to a certain character for an input or correction. With the navigation key you can move the cursor to the left or right. Move the cursor with the horizontal navigation key. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Left: Scrolling back through the menu Right: opens displayed menu, scrolls forward through the menu, retrieves detailed information. Vertical navigation key: Up: scrolls upwards in the list. Down: scrolls downwards in the list. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 33
Activated features is opened. Activated features are also available via the menu: Menu > Activated features. Reset Press the Reset softkey to deactivate the function you want. ➔ The function is now deactivated. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• New voice message or new text message • Appointment call Flashes slowly • Battery almost empty • Not subscribed to any system Flashes alternately The phone is switched off and is being charged in the charging unit Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Note: If the phone is unable to find a matching user, List empty will appear on the dis- play. Press the Call key. ➔ The phone number displayed is dialled. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 37
Notes: • The search function is not affected by upper/lower case and special charac- ters. • If the phone is unable to find a matching user, List empty will appear on the display. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 38
Hides the display. The entry remains stored in the list of the last unanswered calls, is displayed. Note: The call list of unanswered calls can also be selected using the menu: Menu > Call lists > Missed calls. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 39
To scroll through the call numbers last dialled, press the navigation key down- wards. Press the Call key. ➔ The phone number displayed is dialled. Note: Redial list can also be selected using the menu: Menu > Call lists > Redial. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 40
You can only have 1callback activated at a time and only 1 callback can be expected from you. Your callback request will automatically be cancelled by the system after about half an hour. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 41
• You can also find the call number of the user you want in the phone book or in a call list. • If the user you want to deflect to is busy, the call will not be deflected. The display shows Busy and your phone still rings. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 42
Note: If the person rejects your call request or if call waiting is not possible, the call is, depending on the system’s configuration, disconnected (busy tone) or for- warded to a preconfigured destination. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 43
End call Ending a current call: Press the End call softkey. ➔ The first call is terminated. You are now connected with the party who initi- ated the call waiting. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 44
Confirm the user with the softkey. ➔ User is made aware of the announcement. You can now talk. You can also start the announcement using Menu > Call features > Announce- ment > User/Group. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 45
PIN", page or use the function code *47 (see "User’s Guide Function Codes" on the Aastra DocFinder). If you have forgotten your PIN, your system administrator can reset it to the default setting. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• If the other user does not answer, you can cancel the enquiry call with the End call softkey and take back the first call. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 47
The call party on hold is now included in the call. Note: Depending on the system’s configuration you may hear an attention tone. Leaving a conference call: Press the End key. ➔ The other conference parties remain in the call. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 48
Wait for the first ringing tone, then press the End key. ➔ The other party is then called directly by your first call partner. Note: Recall: If the other party does not answer, the call comes back to your phone. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 49
• During an incoming/outgoing call • in call preparation; • During dialling with a busy line. Call recording only starts when the connection is set up. Therefore, no ring-back tones or wait tones are recorded. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 50
End the recording with the Stop softkey. ➔ The recording is sent to your e-mail address. Call recording overview: You can find the call recording overview in your e-mail box. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
3.30 pm, the duration of your Outlook appointment automatically adapts to 3.3 pm. Contact your system administrator for more information. • All the configuration possibilities for a presence profile can be found in chapter "Configuring presence/presence profile", page Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 52
To check a user's presence state: Enter an internal name (see chapter "Dialling by name (Quickdial)", page 36). Select the user you want from the phone book or a call list. ➔ Presence status is displayed. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 53
Forward to voice mail. 3. Scroll to Voice mail greeting and select Absence information. ➔ The setting is stored. Your caller hears the selected absence information, fol- lowed, if applicable, by time and date. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 54
56) or to a Text message (see chapter "Forwarding to a message", page 57). • You can also activate forwarding by remote control, see chapter "Setting functions by remote control", page 77. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 55
• You can also forward calls to your Voice mail (see chapter"Forwarding to voice mail", page 56). • You can also activate call forwarding by remote control, see chapter "Setting functions by remote control", page 77. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 56
(Forwarding on no reply), or only if you are already on the phone (Forwarding if busy). • A new voice mail message is signalled with a text message on the display and a red-flashing LED indicator in the idle state. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 57
Text message Scroll to Text message and confirm with the softkey. <Text> Enter the text and confirm with the softkey. ➔ Forwarding is activated. To deactivate forwarding: Press Menu > Activated features > Reset. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
56. • To find out how to configure a voice mail, refer to the chapter "Configuring voice mail", page or in the "User’s Guide Voice Mail Systems" on the Aastra DocFinder. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 59
<Phone number> Enter the call number and press the softkey. If you wish to keep a copy of the voice message, answer the questions with the softkey. ➔ The voice message is sent. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 60
<Phone number> User and Group: Enter the call number and press the Send softkey. ➔ The text message is sent. Note: If the display shows Not available, the text message could not be sent. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 61
Text message > Inbox to select the text message and continue as described above. Note: You can select and read a new text message even during an active call using Text message > Inbox. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Enter the number of the phone from which you want to pick up the call and confirm with the softkey. Note: You can also find the call number of the user you want in the phone book or in a call list. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 63
➔ Repeats the alarm. Reading the alarm: Read Press the Read softkey. ➔ Displays detailed information; the alarm is not deleted. Delete Deleting the alarm: Press the Delete softkey. ➔ Deletes the alarm. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 64
PIN", page or use the function code *47 (see "User’s Guide Function Codes" on the Aastra DocFinder). If you have forgotten your PIN, your system administrator can reset it to the default setting. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 65
100). MCID During a call: Press the function key for MCID. MCID After the call do not hang up: press the function key for MCID while you hear the busy tone. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 66
Personal call routing is activated. To deactivate personal call routing: Press Menu > Activated features > Reset. Renaming personal call routing: Press Menu > Settings > General > Personal call routing > Change. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 67
This function must be stored under a function key (see chapter "Configuring keys", page 100). Ring alone In the idle state: Press the function key for Ring alone. ➔ Ring alone is activated/deactivated. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 68
Avoid these moni- toring gaps by activating a call forwarding on the monitoring phone. A verification call of the destination phone is yet possible with call forwarding. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 69
Destination number, enter the destination number and press the Save softkey. Note: Test call destination > Select allows you to test the phone number you have entered to make sure it is correct. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 70
• If you intend to use this function notify your call party in advance. <Phone number> 1. Enter the call number of the user you want. 2. Once the busy tone sounds, press key 4. ➔ Silent intrusion is activated. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 71
<Call number, PIN> Enter phone number and PIN and confirm with the softkey. ➔ You are now logged in and can use the free seating phone with your per- sonal settings. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 72
Your system administrator can set a delay (0-60 seconds, depending on the Aastra system phone). During this delay the user can enter another call number in order not to trigger a call on the hotline destination number. If the user does not dial another phone number during this predefined time or puts the handset back down again, a connection with the Hotline number is automatically set up.
Functions with OpenCount OpenCount is a software package used for the call logging management on the communication system. The application can be integrated into your Aastra com- munication system and enables the logging, the administration, and the analy- sis of all call and connection data.
Aastra Alarm Server is used. A patient needs help and presses the alarm button. The Aastra Alarm Server sends a visual (e.g.
Page 75
"Starting an announcement", page 44). The differences are as follows: • Direct response can only be used with a specifically configured Aastra Alarm Server. • Direct response can only be triggered using the Direct response softkey once an alarm is received.
Page 76
Your system administrator can set a delay (depending on the Aastra system phone). During this delay the user can enter another call number in order not to trigger a call on the hotline destination number. If the user does not dial another phone number during this predefined time or puts the handset back down again, a connection with the Hotline number is automatically set up.
PIN", page or use the function code *47 (see "User’s Guide Function Codes" on the Aastra DocFinder). If you have forgotten your PIN, your system administrator can reset it to the default setting. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
If you cordless phone cannot find a system, the display shows "No system". You can switch to an available system using Menu > Settings > System > System reg- istrations (see chapter l "Managing communication systems", page 92). Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 80
Scroll to Settings and press the Select softkey. General Scroll to General and press the Select softkey. Barring Scroll to Barring and press the Select softkey. ➔ You are prompted to enter your PIN. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 81
Select softkey. ➔ The phone is unlocked. ➔ To unlock all your phones, execute the function code #33* <PIN> # (see "User’s Guide Function Codes" on the Aastra DocFinder). Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 82
Progressive ring tone, Suppress ring tone. List of melodies (incl. the alarm melodies) is available to listen to. Note: Your settings for Suppress ring tone can be overruled by the alarm server. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 83
Select softkey. General Scroll to General and press the Select softkey. Direct call answer Scroll to Direct call answer and activate or deactivate with the Select softkey. ➔ The setting is stored. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Scroll to the display setting you want and press the Select softkey. <Display setting> Select the display setting you want. Note: The Select softkey displays the colour scheme you want. ➔ The setting is stored. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
You want to adjust the volume while in a call. You have to set the volume of handset and loudspeaker separately. The new volume will remain stored even after the call is ended. Louder: Press the upper sidekey during the call. Quieter: Press the lower sidekey during the call. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
(not for connections with Bluetooth headset and in hands-free mode). It’s recommended to create a "Loud environment" profile. • Confirmation tone: Each keystroke is confirmed with a beep. • Battery warning: Battery nearly run-down triggers a warning. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 87
The audio profiles are also available via the menu: Menu > Settings > Audio pro- files. ➔ All the audio profiles are displayed. Select Select the audio profile you want and activate with the Select softkey. ➔ Audio profile is activated. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
If you answer a call in headset mode using the Call key or Loudspeaker key, the call is provided on the headset. Note: To find out how to make phone calls with the headset, refer to the chapter "Using a headset", page 27. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Scroll to Settings and press the Select softkey. General Scroll to General and press the Select softkey. DTMF Scroll to DTMF and activate or deactivate with the Select softkey. ➔ The setting is stored. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 90
The new PIN is stored. Notes: • For each digit entered, the display shows an "*". • You can also change the PIN with function code *47 (see "User’s Guide Func- tion Codes" on the Aastra DocFinder). Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 91
2. Enter the PIN you want and confirm with the softkey. ➔ The setting is stored. Note: Delete the current PIN if you prefer to enter your alarm settings without the Admin PIN. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 92
Press the navigation key to the right or the Menu softkey. Settings Scroll to Settings and press the Select softkey. System Scroll to System and press the Select softkey. System registrations Scroll to System registrations and press the Select softkey. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 93
SW version/Owner ID Select required setting (SW version/Owner ID) auswählen. ➔ The information can now be retrieved. The software version is also available via service menu: Press and hold down key 5 version. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Select the protection setting you want and activate or deactivate with the Select softkey. ➔ The setting is stored. Note: You can deactivate an activated protection using Menu > Activated features > Reset. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
1. Select the contact you want. 2. Use the right navigation key to open the contact and highlight the call num- ber you want. 3. Specify the selected phone number as default number using the Default softkey. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 96
Save softkey. New contact Adding new contact: Press the Add new contact softkey, select the number type you want, and con- firm with the Save softkey. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
"Forwarding to voice mail", page 57. • For further information on voice mail refer to the chapter "Listening to voice message", page or in the "User’s Guide Voice Mail Systems" on the Aastra DocFinder. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
If you renamed your personal greeting, your greeting name is displayed here. Your caller obtains one of the personal greetings. The time and date are never given in the global greeting and personal greetings. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 99
After you have changed and saved the active presence profile you have to tem- porarily select another presence profile and then reactivate the presence pro- file you want in order to have the settings applied. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
1. Press the Modify softkey. 2. Make the changes and confirm with the Save softkey. ➔ Key assignment is stored. Delete Deleting a key assignment: Press the Delete softkey. ➔ Key assignment is deleted. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 101
Contact your system administrator for more information. More information on how to store functions under a configurable key using function commands and function code can be found in chapter "Formulating functions", page 104. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 102
This function lets you prevent your call number from being displayed to the CLIR caller. For further information refer to chapter "Suppressing your call num- ber from your called party's terminal display", page 65. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 103
73. You can charge the charges and call information of your outgoing PIN call rebook and incoming calls to certain projects . For further information refer to chapter "PIN telephony", page 73. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
The function commands are listed here; the function codes can be found in the User's Guide "User’s Guide Function Codes" on the Aastra DocFinder. You can use function commands to define a function to suit your personal require- ments. A function can consist of one or more function commands, function codes, and the phone number.
Page 105
• You can only activate certain function codes if the same function cannot be obtained via the menu. • The availability of certain function code may be restricted depending on the sys- tem and software version. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Installation and first-time operation Equipment provided Charging unit and plug-in power Cordless phone Standard battery supply unit with country-spe- cific adapters Quick User's Guide and safety Screwed-on belt information Options Carry strap Swivel belt clip Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
The charging unit and plug-in power supply vary from country to country. Software New phone software can simply be updated during operation using automatic firm- ware updates, reducing maintenance costs as a result. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
• Poor radio links (sizeable distance to the system’s radio station) will reduce the phone’s standby and talk times. The standby and talk times are also reduced by high loudspeaker, ring tone volumes or frequently used keypad and display back- lighting. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
The top part of the carry clip has two openings. You can feed the bottom end of the carry strap through these openings (detach the carry clip first before fitting the strap). Carry straps are optionally available. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
A registration entry contains, among others, a system name (e.g. A,B,C). If your phone is registered with several systems, the name of the active system is shown on the display. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Phone calls can be made, but no names are displayed; the key configuration is missing, and the phone does not respond to function commands Restricted mode following a software update without update licence. Note: For all other messages, faults and questions you may have, contact your system administrator. Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
The corresponding text sections are identified by a letter inside square brackets [a]. The list below indicates which system versions support the relevant features. Contact your system administrator for more information. R1.2 R2.0 R3.0 Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Standard battery: 850 mAh lithium ion Operating time, talk time up to 12 hours Operating time, standby up to 100 hours Charging time in the charging unit 2 hours for fully charged state Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 116
Charging unit without plug-in power supply Length x Width x Depth: 76 x 75 x 24 mm 40 g Power supply ID: 23-00-1061-00 or 23-00-1089-00 ID: 23-00-1089-00 Surface finish (sides and front) Silicone treated Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Index Inserting the battery ........... 109 Brokering ................47 Aastra Alarm Server ............74 Absence information ............53 Accessories (Safety information) ........ 7 Call duration ..............24 Actions following an alarm ........63 Call forwarding : Alarm: Protection setting ...........94 Range alarm ..............82 Call Forwarding on No Reply ........55 Server alarm ..............82...
Page 119
MCID ...................65 Ring volume ..............86 Medical equipment (Safety information) ....6 Risk of explosion (Safety information) ..... 6 Menu-guided navigation ..........32 Room monitoring: Moving the cursor ............31 Activating/deactivating ........68 Muting the microphone ..........26 Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 120
Transferring a call partner ...........48 Troubleshooting ............113 Undoing actions .............33 Unlock: Phone ................81 Unlocking: the keypad ..............80 Upper and lower case ..........31 User information .............. 9 Using the display and operating elements ..28 Voice message: Aastra 610d eud-1290/1.2 – R3.0 – 04.2013...
Page 121
Conformity Aastra Telecom Schweiz AG hereby declares that • the Aastra 400 products conform to the basic requirements and other relevant stipulations of Directive1999/5/EC. • all our products are manufactured in conformity with RoHS (2011/65/EU). The product-specific declarations of conformity can be found on the Aastra DocFinder: www.aastra.com/docfinder.