Advertisement

Quick Links

Instruction Manual
The Breeze
®
Export Model No. 3030-01-000
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
© 2018 Gold Medal Products Co.
Part No. 110050

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the The Breeze 3030-01-000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Gold Medal The Breeze 3030-01-000

  • Page 1 Instruction Manual The Breeze ® Export Model No. 3030-01-000 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA © 2018 Gold Medal Products Co. Part No. 110050...
  • Page 2: Safety Precautions

    The Breeze Export Model No. 3030-01-000 SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning.
  • Page 3 Note: Improvements are always being made to Gold Medal’s equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions.
  • Page 4: Inspection Of Shipment

    Whirlgrip Floss Stabilizer Aluminum Floss Pan *CAUTION: If supply cord is damaged, it must be replaced by a special cord or assembly available from (PN 42372) Gold Medal Products Co. or IEC Power Cord* Instruction Registration its service agent. Manual Warranty Card gmpopcorn.com...
  • Page 5: Setup For Use

    The Breeze Export Model No. 3030-01-000 (General reference images shown) Setup for Use Spinner Head Bell Housing Lock-N-Go Handle Step 2: Lock-N-Go® handles are used for transport. Rotate both Step 1: Set unit on a level handles to a vertical, UNLOCKED, position for use. This allows surface.
  • Page 6 The Breeze Export Model No. 3030-01-000 Whirlgrip Floss Stabilizer Installation Instructions Unit must be OFF, and cool to install Floss Stabilizer. Place Floss Pan on unit and install Whirl Grip Floss Stabilizer (Item No. 3010) as shown below. Kit includes: Floss Stabilizer/screening (P/N 43032), and (6) Whirlgrip Clips (P/N 77470).
  • Page 7: Electrical Requirements

    The Breeze Export Model No. 3030-01-000 Electrical Requirements The following power supply must be provided: 3030-01-000: 230 V~, 996 W, 50 Hz DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water.
  • Page 8: Controls And Their Functions

    The Breeze Export Model No. 3030-01-000 OPERATING INSTRUCTIONS Controls and Their Functions Two position, lighted rocker switch - turns Motor ON/OFF and supplies power to the Heat MOTOR & MASTER SWITCH Switch. The green light ON indicates there is power to the unit. Two position, lighted rocker switch - turns the heating element ON/OFF.
  • Page 9 The Breeze Export Model No. 3030-01-000 Sugar for Your Candy Ready to Use Flossugar Our ready to use Flossugar is the preferred sugar for your new cotton candy machine; however 100% pure cane or beet sugar will do just fine. Our Flossugar gives you good rich colors, and great flavors, too.
  • Page 10: Machine Operation

    The Breeze Export Model No. 3030-01-000 Machine Operation Floss Machine Operation (3030 Breeze) WARNING Floss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection.
  • Page 11 The Breeze Export Model No. 3030-01-000 Making Floss Pick a cone, if it sticks in the stack of cones, twist it off the stack. CAUTION Keep hands away from spinning head! Hold an inch or two of the pointed end of a cone between two fingers and a thumb. With a light 031_021914 flicking action, roll cone in the web of floss building up in the pan.
  • Page 12 The Breeze Export Model No. 3030-01-000 Floater Adjustments In operation, the floss will collect on the FLOSS STABILIZER. If the floss collects “low” on the stabilizer, twist the front (leading) edge of the leather floaters down. You get more lift and the floss will collect higher.
  • Page 13: Shutdown Procedure

    4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive materials as they will damage parts of machine.
  • Page 14 The Breeze Export Model No. 3030-01-000 Floss Band and Element Disassembly and Removal of Floss Band 1. Unplug the machine from the power source and allow floss head to cool completely. 2. Remove all sugar from the head of the machine before disassembling. If needed, carefully turn the machine on its side and shake the sugar out.
  • Page 15 The Breeze Export Model No. 3030-01-000 Reassembly of Floss Band 1. The band is marked to show correct orientation for installation (see image below). 2. Always attach one element lead to each terminal assembly (see image below). 3. Reassemble terminal guard, lock nut, and nylon acorn nut. 4.
  • Page 16: Troubleshooting

    The Breeze Export Model No. 3030-01-000 Troubleshooting A. Excessive carbon on the A. Follow the instructions for removing and Issue Possible Cause Solution element. cleaning band and element (see Floss Band Low Production and Element section). B. Heat Control B. Adjust the Heat Control Knob to increase production.
  • Page 17 The Breeze Export Model No. 3030-01-000 A. Packing material not A. If the equipment is new, check that all packing Issue Possible Cause Solution removed. materials were removed from the machine. Excessive Vibration B. Lock-N-Go Handles not in B. Verify that the Lock-N-Go Handles have been operating position.
  • Page 18: Maintenance Instructions

    The Breeze Export Model No. 3030-01-000 MAINTENANCE INSTRUCTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning.
  • Page 19: Ordering Spare Parts

    4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order. 5. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online:...
  • Page 20 The Breeze Export Model No. 3030-01-000 Cabinet Exterior and Lock-N-Go Handle Assembly 30, 31 28, 29 26, 27 *CAUTION: If supply cord is damaged, it must be replaced by a special cord or assembly available from Gold Medal Products Co. or its service agent.
  • Page 21 The Breeze Export Model No. 3030-01-000 Cabinet Exterior and Lock-N-Go Handle Assembly – Parts List Part Number Item Part Description SPINNER HEAD, TUBULAR 5IN (Complete Assy.) 3030-01-000 See Spinner Head Assembly section for individual 42283TX parts breakdown. BRUSH HOLDER ASSY (includes Brushes, Caps and Holders) See Brush Assembly Breakdown 42383W section for individual parts breakdown.
  • Page 22 The Breeze Export Model No. 3030-01-000 5” Spinner Head (Model No. 42283TX) – Parts Breakdown Spinner Head Complete (Model 42283TX) 9, 10 *Uses two Set Screws Floss Head – Band Interior View Spinner Head Bottom gmpopcorn.com Page 22...
  • Page 23 The Breeze Export Model No. 3030-01-000 5” Spinner Head (Model No. 42283TX) – Parts List Part Number Item Part Description LEATHER FLOATER 20010 42283TX SCREW 8-32 X 5/16 PH PAN MS 89247 HIGH CAPACITY SPINNER CAP 43166 10-24 X 2 1/2 PHIL/SLT MS 20058 BREEZE BAND ASSEMBLY (includes element) 48799EX...
  • Page 24 The Breeze Export Model No. 3030-01-000 Bell Housing Interior – Brush Assembly 1, 2 5, 6 Part Number Item Part Description HEX NUT #10-24 ESLOK 74691 3030-01-000 .188ID FLATWASHER 77052 MOTOR MTG PLATE 42119 MOTOR, FLOSS MACHINE 48649EX 6-32 X 1/2 PH PAN HD M/S 47516 6-32 GRIP NUT ZINC PLATED 47517...
  • Page 25 The Breeze Export Model No. 3030-01-000 Cabinet Interior – Parts Breakdown 3030-01-000 5, 6 5, 6 • Be sure the Bell Housing is located UNDER When reassembling the unit: 5, 10 the Clamping Brackets as shown here. • Be sure to keep wiring clear of the locking mechanism.
  • Page 26 The Breeze Export Model No. 3030-01-000 Cabinet Interior - Parts List Part Number Item Part Description MOTOR, FLOSS MACHINE 48649EX 3030-01-000 1UF 250VAC CAPACITOR 55515 10 AMP EMI FILTER 13302 RELAY, 240 VAC, DPST NO 48590EX 6-32 X 3/8 PHIL PAN M/S 39000 6-32 GRIP NUT ZINC PLATED 47517...
  • Page 27: Wiring Diagram

    The Breeze Export Model No. 3030-01-000 Wiring Diagram Model No. 3030-01-000 gmpopcorn.com Page 27...
  • Page 28: Warranty

    © 2018 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.

Table of Contents