Related Manuals for Gold Medal Floss-Boss 3024EX
Summary of Contents for Gold Medal Floss-Boss 3024EX
- Page 1 Floss-Boss Part No. 42543EX Revised October, 1999 Instruction Manual Model #3024EX Cincinnati, OH 45241-4807 USA e-mail: goldme19@eos.net www.gmpopcorn.com...
-
Page 2: Safety Precautions
Always unplug the equipment before cleaning or servicing. NOTE The information, specifications and illustrations contained in this manual represent the latest data available at time of publication. Right is reserved to make changes as required at the discretion of Gold Medal Products Company without notice. -
Page 3: Electrical Requirements
ELECTRICAL REQUIREMENTS The GOLD MEDAL Floss machine requires a 230 volt, 50 cycle standard wall receptacle. The power supply cord is equipped with a machine ground (the tubular prong on the male plug). - Page 4 Floss Machine Before Plugging in the Machine Remove all padding and restraints. Lower the shipping bracket so the bell housing "floats" freely on the springs. Unscrew and push down the two knobs on each side of the cabinet top to lower the shipping bracket completely.
- Page 5 The easiest way to make sure you have the right texture sugar with proper flavor and colors is to use GOLD MEDAL FLOSSUGAR. FLOSSUGAR gives good, rich colors and flavors, and does not exceed the color limitations imposed by the Food and Drug Administration. FLOSSUGAR comes in sealed, plastic-coated cartons with handy pouring spouts for filling.
- Page 6 Floss Machine MAKING FLOSS Pick a cone; if it sticks in the stack of cones, twist it off the stack. Hold an inch or two of the pointed end of the cone between two fingers and a thumb. With a light flicking action, roll cone in the web of floss building up in the pan.
-
Page 7: Shutdown Procedure
Floss Machine FLOATER ADJUSTMENT In operation, the floss will collect on the FLOSS STABILIZER (if used). If the floss collects “low” on the stabilizer, twist the front (leading) edge of the leather floaters down. You get more lift and the floss will collect higher. -
Page 8: Maintenance Instructions
Floss Machine MAINTENANCE INSTRUCTIONS THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN- TENDED ONLY FOR QUALIFIED FOOD EQUIPMENT SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIP- MENT. THESE ARE NOT INTENDED FOR THE OPERATOR. Adequate eye protection must be used when servicing this equip- ment to prevent the possibility of injury. - Page 9 GOLD MEDAL Floss Ribbons (heat elements) are made of nickel wire with ceramic insulation at the terminal point and on the lead wires. They are designed to be as reliable as the GOLD MEDAL Floss Bands: however, the ribbons must be handled carefully. DO NOT stretch the ribbon or it will not function properly.
-
Page 10: Troubleshooting
Floss Machine TROUBLESHOOTING LOW PRODUCTION 1. Check for excessive carbon on the ribbons. Follow the instructions for removing and cleaning band and ribbon if needed. 2. Check heat control for correct setting. 3. Check the line voltage. A primary reason for low production and poor equipment performance is low line voltage. -
Page 11: Ordering Spare Parts
3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 or, place orders at:... - Page 12 Floss Machine FLOSS MACHINE ASSEMBLY FLOSS FLOSS FLOSS FLOSS FLOSS BOSS BOSS BOSS BOSS BOSS 42543EX...
- Page 13 Floss Machine PARTS LIST – FLOSS MACHINE CABINET ASSEMBLY Model #3024EX Item No. Part No. Description 42450 Cabinet Welded Assembly 47155 Molded Recessed Bumper 42369 Power Supply Cord 41098 Handle 42120 Suspension Spring #6-32 x 5/8 Ph Pan Hd Screw 12603 Nameplate 42448...
- Page 14 Floss Machine PARTS LIST – FLOSS MACHINE HEAD ASSEMBLY Model #3024EX Item No. Part No. Description 42283EX Spinner Head Complete 42045 8-32 x ¼ HX HD Whizlock 43166 Spinner Cap, High Capacity 42284 Spinner Head Bottom Only 43165 5½” Floss Band 42338 5"...
-
Page 15: Electrical Schematic
Floss Machine ELECTRICAL SCHEMATIC 42543EX... -
Page 16: Warranty
WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any...