Page 2
This publication is subject to change. bintec elmeg offers no warranty whatsoever for information contained in this manual. bintec elmeg is not liable for any direct, indirect, collateral, consequential or any other damage connected to the de- livery, supply or use of this manual.
1 About this manual bintec elmeg Chapter 1 About this manual This installation manual for the bintec RM3000 router family contains information on how to correctly install the device in a working environment. 1.1 Supported devices The information provided in this installation manual only applies to the bintec RM3000 router family.
12. 2.1.2 Hardware monitoring The LEDs on the front panel help monitor the bintec RM3000 hardware. They provide visual information on the status of hardware components and indicate whether there is connectivity, data flow, etc. For further information on the LED panel, please see Components on page 5.
3 Components and power supply bintec elmeg Chapter 3 Components and power supply This chapter describes the bintec RM3000 router family chassis and its main components. The following sections are included: • Components • Assembly instructions • Installing and uninstalling modules •...
0 (all LEDs off) to level 4 (all lit up). (1, 2, 3, 4) 3.1.2 Rear panel The following image shows the rear panel of the bintec RM3000 router, which contains the majority of connectors. RM3000 Router...
Two Wi-Fi connectors and two 3G antenna connectors can be found on each side panel: Fig. 4: Right and left-hand side panels Fig. 3: The connectors are as follows: Side panel connectors Item Description Wi-Fi antenna connectors. 3G antenna connectors. 3.1.4 Underside panel The following image shows the underside panel: RM3000 Router...
Adhesive rubber feet (not required when the device is mounted on a rack). 3.2 Expansion slot The bintec RM3000 router comes with an expansion slot that allows you to increase the number of features and in- terfaces the router has by inserting different cards or boards.
Page 15
Use appropriate screws to affix the card to the tray, being careful not to damage the card when tightening the screws. Please see Fig. 8 on page 9. Installing the expansion card Fig. 8: (6) Finally, insert the tray into the device once again using the appropriate guides. See Fig. 9 on page 10. RM3000 Router...
(8) Connect a terminal to the console to ensure the device can detect the expansion card. 3.3 Installing in a rack The bintec RM3000 router can be mounted in a 19-inch rack. Rack rails and screws are not provided and must be purchased separately.
3.3.2 Mounting on a wall An optional wall mount kit is available for the bintec RM3000. The kit can be ordered separately or together with your bintec RM3000 router. The anchors to mount the device on the wall must be installed as shown in the following figure, using the screws provided by the manufacturer.
Fig. 13 on page 12. 3.5 Power source The bintec RM3000 router is powered by an external AC/DC source. Workplace conditions. Main characteristics • Do not expose the device to humid and/or dusty environments. • Do not expose the device to direct sunlight or install near any heat sources. Do not place the device amongst pa- pers, magazines or other elements that could hinder natural air circulation.
• Disconnect the data cables. 3.6 RST button The RST button on the rear of the bintec RM3000 router has various functions (described below). 3.6.1 Rebooting the device Once the device is operating normally, pressing the RST button will make it restart.
The bintec RM3000 has two 3G antenna connectors. The antennas are assembled and disassembled by screwing/ unscrewing them into/from the Cell connectors on the router's side panels. Using these antennas with the bintec RM3000 router improves the quality of the signal received and transmitted by the cellular model.
Page 21
The corresponding software license must be installed in the router for the cellular interface to work. Some cellular telephony technologies use the antenna diversity technique to improve the quality of the signal re- ceived (HSUPA, CDMA EV-DO, etc.). For this reason, the bintec RM3000 router family is equipped with several WWAN connectors:...
3G USB Connector Fig. 19: 3.7.6 Connecting for configuration The front panel of the bintec RM3000 features an RJ45 female connector, labeled “ Aux” , that provides access to the router's local console. For further information, please see Connecting to the device on page 27.
3.8 SIM card installation You may need to insert a SIM card in the bintec RM3000 before you can use the WWAN interface. Some countries have services (CDMA) that do not require SIM cards. The bintec RM3000 has two SIM trays.
Page 24
(5) Hold the SIM card case cover down while you slide the cover to the side, as indicated by the arrow labeled LOCK, until it is firmly in place. Inserting the SIM in the internal tray Fig. 24: RM3000 Router...
NO.5 LANE 83. LUNG-SOU ST, TAO-YUAN CITY, TAIWAN R.O.C. Input Voltage 100-240 Vac Input AC frequency 50-60 Hz Output voltage 12.0 V Output current 5.0 A Output power 60,0 W Average active efficiency 88.3% Efficiency at low load (10%) 87.2% RM3000 Router...
Directiva 2014/35/UE (LVD) Directiva 2009/125/CE (ErP) Directiva 2011/65/UE (RoHS) del parlamento Europeo. The EC declaration of conformity and additional product documentation can be found at: http://www.bintec-elmeg.com/conformity 4.7 CE marking This equipment is in conformity with the CE procedures and marking. RM3000 Router...
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4.10.3 Radio frequency interference requirements High power radars are allocated as primary users of the 5.25 - 5.35 GHz and 5.65 - 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. RM3000 Router...
This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or trans- mitter except in accordance with IC multi-transmitter product procedures. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur. RM3000 Router...
A.3 Connecting to the device A.3.1 Connecting using the local console (Aux connector) An RJ45 female connector, labeled “ Aux” , on the front panel of the bintec RM3000 router provides access to the device's local console. RM3000 Router...
Fig. 27: A.4 Licenses The bintec RM3000 router family offers a series of licenses. Among them, the following stand out: WiFi: Activation license for the WLAN 802.11bgn. USB: Activation license for the USB port to be used for the WWAN modems.
Adjustable in the following steps: 5, 8,11,14,16 dBm and maximum. Maximum antenna gain) power varies depending on the data rate, frequency band and country setting. Bandwidth (802.11n) 20/40 MHz (bundling two adjoining 20 MHz channels into one 40 MHz channel). CONECTOR Up to 3 RF RP-SMA female. RM3000 Router...
LENGTH x WIDTH x HEIGHT 245 x 210 x 45 mm. WEIGHT 1.4 kg. A.6.11 Environmental specifications TEMPERATURE OPERATING NORMALLY: 0 ºC to 45 ºC STORED: -25 ºC to 70 ºC RELATIVE HUMIDITY On: 5 % to 90 % RM3000 Router...
Need help?
Do you have a question about the RM3000 and is the answer not in the manual?
Questions and answers