Page 2
Ruijie Networks reserves the right to modify the content of the document without any notice or prompt. This manual is designed merely as a user guide. Ruijie Networks has tried its best to ensure the accuracy and reliability of the content when compiling this manual, but it does not guarantee that the content of the manual is completely free of errors or omissions, and all the information in this manual does not constitute any explicit or implicit warranties.
Intended Audience This document is intended for: Network engineers Technical support and servicing engineers Network administrators Technical Support Official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee Technical Support Website: https://www.ruijienetworks.com/support Case Portal: https://caseportal.ruijienetworks.com Community: https://community.ruijienetworks.com ...
Page 4
The example of the port type may be different from the actual situation. Please proceed with configuration according to the port type supported by the product. The example of display information may contain the content of other product series (such as model and description).
Contents Preface ..............................I Contents ..............................I 1 FAQs About Login ..........................1 1.1 What Is the Default Management IP Address of a Reyee EST Series Wireless Bridges? ..1 1.2 How Do I Log In to a Reyee EST Series Wireless Bridge?............1 1.3 What Can I Do If I Fail to Log In to the Eweb Management System? ........
Page 6
7 FAQs About Parameters of Reyee EST Series Wireless Bridges ..........20 7.1 Where Can I Find All Parameters of Reyee EST Series Wireless Bridges? ......20...
Place the target device around the wireless bridge when connecting the target device. Click Create a Project. You can add devices on Ruijie Reyee App by either Connect to Wi-Fi or Scan or enter SN.
Page 8
Connect to Wi-Fi: Tap Wireless Bridge and tap Start. Tap Connect to connect to the default SSID @Ruijie-bxxxx, where xxxx is the last four digits of the MAC address. Check the MAC address at the bottom label of the device.
Page 9
FAQs FAQs About Login Check whether devices are detected. Tap Next. Name the project and enter the management password.
Page 10
FAQs FAQs About Login Configure uplink settings and select the Internet connection mode of a WAN.
Page 11
FAQs FAQs About Login Configure the SSID, password, and country code.
Page 12
FAQs FAQs About Login Tap Save. Scan or enter SN Tap Scan QR-code. Scan the QR code at the bottom label of the device. The App automatically identifies the default Wi-Fi of the wireless bridge. Tap Connect to connect to the default Wi-Fi.
FAQs FAQs About Login Enter the management password and tap OK. What Can I Do If I Fail to Log In to the Eweb Management System? (1) Check that the network cable is properly connected to the LAN port of the device and the corresponding LED indicator blinks or is steady on.
Page 14
FAQs FAQs About Login (2) Before accessing the configuration GUI, configure automatic IP address assignment (recommended), so that the server with DHCP enabled can automatically assign an IP address to the PC. To allocate a static IP address to the PC, set the IP address of the PC on the same network segment as the IP address of the management interface.
FAQs FAQs About the Password FAQs About the Password What Is the Default Login Password Reyee EST Series Wireless Bridges? A Reyee EST wireless bridge does not have the default username and password. You can log in directly upon first login. How Do I Change the Device Login Password? There are three ways to change the device login password: ...
Page 16
If there is a non-bridged device on the network, the admin password will be disabled. If the device is online on Ruijie Cloud, you can modify the management password on the Ruijie Cloud Eweb. Select a project from Project List and click Devices>Project Password.
(1) If you manage your Reyee EST series wireless bridge on Ruijie Cloud, you can change the password through Ruijie Cloud. (2) If the Reyee EST series wireless bridge is not on Ruijie Cloud, you can press the reset button on the wireless bridge for more than 5s to restore factory settings.
Page 18
FAQs FAQs About the Password Caution Restoring factory settings will delete the existing configuration and you are required to configure the device again at your next login. Therefore, exercise caution when performing this operation.
FAQs FAQs About DHCP FAQs About DHCP What Should I Do If the Device Cannot Obtain an IP Address Through DHCP? (1) Check the DHCP server configuration. Check whether DHCP is enabled. Check whether the DHCP address pool is configured. Check whether the number of IP addresses in the DHCP address pool is sufficient.
FAQs About the Wireless Configuration What Is the Default Wi-Fi Name of a Reyee EST Series Wireless Bridge? For Reyee EST series wireless bridges, the default Wi-Fi name is @Ruijie-bxxxx. How Are Radio Settings Adjusted When the Wireless Network Quality Is Poor? The device detects the surrounding wireless environment and selects the appropriate configuration upon power- on.
Page 21
FAQs FAQs About the Wireless Configuration The camera mode does not support independent channel settings. After the channel at the NVR end is adjusted, the camera end automatically changes its channel to be the same as the NVR end. Note The available channel is related to the country or region code.
Page 22
FAQs FAQs About the Wireless Configuration 2. Optimizing the Channel Width Choose Wireless > WDS > Channel & Transmit Power > Channel Width. If the interference is severe, select a lower channel width to avoid network freezing. A 5 GHz bridge supports channel widths of 20 MHz, 40 MHz, and 80 MHz, while a 2.4 GHz bridge supports channel widths of 20 MHz and 40 MHz.
Page 23
FAQs FAQs About the Wireless Configuration 4. Configuring the Distance Choose Wireless > WDS > Channel & Transmit Power > Distance. It is recommended that the configured distance between the NVR and camera be greater than their actual distance. If the configured distance is much smaller than the actual distance, the wireless performance will deteriorate, and the WDS connection may fail.
FAQs FAQs About Port-Based Flow Control FAQs About Port-Based Flow Control What Is Port-Based Flow Control? Flow control can relieve the data congestion caused by ports at different speeds and improve the network speed. How Do I Configure Port-Based Flow Control? Choose Advanced >...
FAQs FAQs About EST Bridge Configuration FAQs About EST Bridge Configuration How Do I Configure PTMP on EST Series Devices? Refer to the link: https://www.ruijienetworks.com/support/video-1880 What Can I Do If I Fail to Configure an EST Series Wireless Bridge? (1) Check the indicator of the EST series wireless bridge.
FAQs FAQs About Parameters of Reyee EST Series Wireless Bridges FAQs About Parameters of Reyee EST Series Wireless Bridges Where Can I Find All Parameters of Reyee EST Series Wireless Bridges? Refer to the link of the device parameter table of Reyee EST series wireless bridges: https://community.ruijienetworks.com/forum.php?mod=viewthread&tid=1819...
Need help?
Do you have a question about the Reyee RG-EST Series and is the answer not in the manual?
Questions and answers