Related Manuals for APG PT-300
Summary of Contents for APG PT-300
- Page 1 PT-300 Pressure Transmitter User Manual Doc #9004025 Part #200382 Rev B, 07/2019...
-
Page 2: Table Of Contents
Table of Contents Introduction ........................ iii Warranty and Warranty Restrictions ..............iv Chapter 1: Specifications and Options..............1 Dimensions ............................1 Specifications ........................... 2 Model Number Configurator ......................3 Electrical Connection, Pinout Table, and Power Supply Table ..........4 Wiring Diagrams ..........................5 Chapter 2: Installation and Removal Procedures and Notes ......6 Tools Needed ............................. -
Page 3: Introduction
PT-300 and this manual. The PT-300 series offers high accuracy and reliability over a wide range of pressures. The small size, integrated electronics, wide operating temperature ranges, and durability make PT-300 instruments perfect for static and dynamic pressure measurements with an amplified output signal. -
Page 4: Warranty And Warranty Restrictions
Warranty and Warranty Restrictions This product is covered by APG’s warranty to be free from defects in material and workmanship under normal use and service of the product for 24 months. For a full explanation of our Warranty, please visit https://www.apgsensors.com/about-us/terms-conditions. -
Page 5: Chapter 1: Specifications And Options
Chapter 1: Specifications and Options • Dimensions .590" [15mm] 1.250" [32mm] Tel: 1/888/525-7300 • Fax: 1/435/753-7490 • www.apgsensors.com • sales@apgsensors.com... -
Page 6: Specifications
• Specifications Performance Pressure Ranges 0 to 10K PSIS (Per Part Number) Analog Output 4-20mA, 0-5VDC, 0-10VDC Over Pressure 1.5X Full Scale or limit of fitting, whichever is less Burst Pressure 3.0X Full Scale or limit of fitting, whichever is less Accuracy Linearity, Hystereses &... -
Page 7: Model Number Configurator
• Model Number Configurator Model Number: PT-300 - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ - _____ A. Operation / Output G. Process Connection □ P5 ▲ 1/4 - 18 NPTF □... -
Page 8: Electrical Connection, Pinout Table, And Power Supply Table
• Electrical Connector, Pinout Table, and Supply Power Table Below are pin out diagrams, a pin out table, and electrical cable specifications for the 4-20 mA, 0-5 VDC, and 0-10 VDC outputs, to assit you in wiring your transducer. PT-300 Pin Out Table 4-20 mA 0-5 VDC... -
Page 9: Wiring Diagrams
• Wiring Digrams 4-20 mA This device is a 2 wire, loop powered transmitter. A voltage of between 9 and 28 VDC must be maintained at this connection. Completion of the earth or system ground is recommended for proper circuit protection. Power supply voltage must be sufficient to maintain a minimum of 9 VDC at the transducer/transmitter terminals after “dropping”... -
Page 10: Chapter 2: Installation And Removal Procedures And Notes
• Removal Instructions Removing your PT-300 from service must be done with care. It’s easy to create an unsafe situation, or damage your sensor, if you are not careful to follow these guidelines: • Make sure the pressure is completely removed from the line or vessel where your sensor is installed. -
Page 11: Chapter 3: Maintenance
Chapter 3: Maintenance • General Care Your PT-300 series pressure transmitter is very low maintenance and will need little care as long as it is installed correctly. However, in general, you should: • Keep the transmitter and the area around it generally clean. - Page 12 Automation Products Group, Inc. Tel: 1/888/525-7300 • Fax: 1/435/753-7490 • www.apgsensors.com • sales@apgsensors.com...
Need help?
Do you have a question about the PT-300 and is the answer not in the manual?
Questions and answers