Wet Pick Up Operation; Blower Feature; Emptying Liquid Waste From The Tank - Shop-Vac 87MT Series Manual

been used to pick up liquids, the foam sleeve must be cleaned and dried before installing for dry
pick up. With tank cover in an upside down position, slide foam sleeve down over lid cage pull-
ing until foam sleeve completely covers lid cage (Figure 44). NOTE: Bottom of foam sleeve must
be positioned on the OUTSIDE of groove around lid cage for the reusable dry filter to fit properly
(Figure 45, 46). Center the reusable dry filter on lid cage (Figure 47), slide mounting ring down
over filter until ring is positioned against the ribs of the lid cage (Figure 48). The reusable dry
filter should always be in position over the foam sleeve for dry pick up. To remove the filter for
cleaning, remove mounting ring and filter from lid cage (Figure 49). To clean the reusable dry
filter, shake off excess dirt and dust or (depending on the condition of the filter) rinse with water.
Allow the filter to dry completely and reinstall. DO NOT MACHINE WASH OR DRY.
IMPORTANT: BEFORE INSTALLING REUSABLE FILTER BE SURE THAT FOAM SLEEVE IS OUTSIDE
OF GROOVE AND AROUND LID CAGE. (Figure 44, 45)
NOTE: ENSURE THAT THE MOUNTING RING IS COMPLETELY SECURE AND IN POSITION BY PRESS-
ING DOWN FIRMLY AROUND THE RING IN SEVERAL PLACES. BE SURE THE REUSABLE DRY DISC
FILTER COMPLETELY COVERS THE FOAM SLEEVE. CHECK TO ENSURE THAT ALL EDGES OF THE
REUSABLE DRY FILTER ARE SECURE UNDER THE MOUNTING RING.
CAUTION
– kEEP FILTERS CLEAN
43
47
46
INSTALLING THE CARTRIDGE FILTER
(Not standard with all models)
NOTE: If foam sleeve is in position over lid cage, it does not need to be removed before
installing cartridge filter. Foam sleeve must be positioned on the INSIDE of groove
located around lid cage for cartridge filter to fit properly.
The cartridge filter can be used for wet or dry pick up; installation is the same for both. When
picking up large quantities of liquid please refer to the Wet Pick Up Operation section in the
manual. Use the cartridge filter in position over the lid cage for most general dry pick up.
Make sure inlet deflector is fully inserted into deflector guide on inside of tank. If it is not, install
inlet deflector by sliding it downward into slot on deflector guide (Figure 50). NOTE: Hose
must be removed before inlet deflector can be inserted into or removed from deflector guide.
Opening on inlet deflector can face either side of tank. Inlet deflector should always be in place
for any type of cleaning. With the tank cover in an upside down position, slide the cartridge
filter down over the lid cage, pushing until the filter seals against the cover (Figure 51).
Place filter retainer into the top of the cartridge filter, hold the tank cover with one hand, turn
the handle on the filter retainer clockwise to tighten, locking the filter into place (Figure 52
& 53). To remove filter for cleaning, hold the tank cover and turn the filter retainer counter-
clockwise to loosen and remove, slide the cartridge filter off the lid cage (Figure 54 & 55).
To clean filter shake or brush off excess dirt or rinse (from the inside of the filter) with water,
dry completely (approximately 24 hours) and reinstall (Figure 56 & 57). NOTE: If the filter has
been used for wet pick up, it must be cleaned and dried before using for dry pick up.
50 51
53 54
INSTALLING THE DISPOSABLE FILTER BAG
(Not standard with all models)
1. Use for dry pick up only. Use in conjunction with cartridge filter for picking up soot,
cement, plaster or drywall dust.
2. With cord disconnected from receptacle, pull latches in an outward motion and remove
tank cover.
3. Unscrew hose locking-nut and remove hose from inlet (Figure 58).
4. Remove inlet deflector from deflector guide (Figure 59). NOTE: Hose must be removed
before inlet deflector can be taken out.
45
44
48 49
52
55
57
5. With the opening of the inlet deflector facing the left or right side of the filter bag, slide
filter bag collar over deflector matching notches of bag collar to tabs on inlet deflector, bag
will only fit properly one way (Figure 60).
6. Slide deflector with collection bag attached into deflector guide (Figure 61).
7. Reinsert hose into inlet and tighten locking-nut (Figure 62).
8. When secured in place, expand bag and position around the inside of tank.
9. Replace tank cover.
NOTE: When removing filter bag from tank, remove inlet deflector from filter bag collar and
reinstall into deflector guide. Inlet deflector should always be in place for any type of cleaning.
58
61

WET PICk UP OPERATION

Remove ALL dirt and debris found in the tank. The vacuum requires
only a minimum of conversion when going from dry to wet pick up.
Remove all dry use filters from the vacuum. A clean cartridge filter may
be used for vacuuming small amounts of liquids. For best results when
vacuuming large quantities of liquid, remove the cartridge filter. When
vacuuming liquids containing debris, it is recommended purchasing a
foam sleeve and installing over filter cage; otherwise a foam sleeve is
not required for wet pick up. Foam sleeve and additional filters may be
purchased by visiting our website at www.shopvac.com, contacting our customer service
department, or purchasing at your local Shop-Vac ® distributor. Make sure inlet deflector is
fully inserted into deflector guide on inside of tank. If it is not, install inlet deflector by sliding
it downward into slot on deflector guide (Figure 63). NOTE: Hose must be removed before
inlet deflector can be inserted into or removed from deflector guide. Opening on inlet deflector
can face either side of tank. Inlet deflector should always be in place for any type of cleaning.
Misting in exhaust air may occur if the filter becomes saturated during wet pick up. If
misting occurs, remove filter and allow to dry or, replace with another dry filter to eliminate
the misting and possible dripping of liquid around the lid. Turn the unit off immediately upon
completing a wet pick up job or when tank is full and ready to be emptied. Raise the hose to
drain any excess liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place
tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid
cage.
2. Shake excess dust off foam sleeve with a rapid up and down movement.
3. Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water
wash is not always required, depending on the condition of the foam sleeve.
4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The
foam sleeve is now ready to be reinstalled on the lid cage.
NOTE: WET PICk UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY
AFTER PICkING UP WET, STICkY kITCHEN ACCIDENTS. THIS CAN BE ACCOMPLISHED
WITH A WARM SOLUTION OF SOAP AND WATER.

BLOWER FEATURE

This vacuum can be used as a powerful blower. To use your unit as
a blower unscrew blower port cover located on the backside of the
motor housing (Figure 64). The blower port cover is equipped with a
retaining strap to prevent loss of the port cover while blower is in use.
Clear hose of any obstructions before attaching to blower port. Insert
hose end with locking-nut into blower port on rear of unit and tighten.
Do not over-tighten. Caution should be used when using as a blower
56
due to the powerful force of air when using certain attachments.
NOTE: For maximum performance, when vacuuming, remove blower
port cover.
WArNING
VENT ROCkS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE
EYES OR FACE WHICH CAN RESULT IN SERIOUS INJURY.
EMPTYING LIqUID WASTE
FROM THE TANk
Not all units are equipped with tank drains. Follow the instructions, which apply to your specific
unit.
Without Tank Drain
Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and remove
the plug from the wall receptacle. Remove the tank cover and deposit the liquid waste contents in a
suitable drain. After tank is empty, return the cover to its original position. To continue use, plug the
60
59
62
– ALWAYS WEAR EYE PROTECTION TO PRE-
63
64