Kärcher Windsor Chariot 2 iScrub 20 Operating Instructions Manual page 91

90 DRIVE LOWER - FROM SN 4
POS Article no. Description
1 8.641-117.0 Traction motor C2
2 8.640-996.0 Chain wheel transmission ANSI 40 13T
3 8.640-995.0 Chain wheel transmission ANSI 40 13T IDL
4 8.640-994.0 Chain wheel transmission ANSI 40 20T
5 8.640-591.0 Bolt 1/2 x 1.625
6 8.638-411.0 Nut M6-1, HEX, SERFLG, DIN6923
7 8.640-539.0 Retaining plate C2
8 8.640-538.0 Axle drive wheel
9 8.640-537.0 Distance holder C2
10 8.640-536.0 Chain ANSI#40 X 21" W/MASTER
11 8.640-535.0 Distance holder C2 MTR MNT HOUSING
12 8.640-533.0 Distance holder C2
13 8.640-532.0 Retaining plate C2
14 8.640-531.0 Housing transmission C2
15 8.639-417.0 Washer M8 FNDR SS DIN 9021
16 8.636-917.0 Wheel 8.00 x 2.00, GRAY X-GRV
17 8.632-671.0 KEY, 5 X 5 X 16MM CS GR1045
18 8.632-167.0 WASHER, .748 SS
19 8.627-607.0 SCREW, 5/16-18 X .75 CARR SS
20 8.627-470.0 SCREW, M6 X 1 X 16 HHCS ZNPLT
21 8.627-462.0 SCREW, 1/4-20 X 1.25 HHMS STL GR5 ZNPLT
22 8.627-375.0 SCREW, 1/4-20 X .625 HHCS SS NP
23 8.627-083.0 NUT, 5/16-18 HEX NYLOCK SS
24 8.621-964.0 KEY, 1/4 X 1/4 X 1.5 LCSTL GR1018
25 8.638-412.0 Screw M5-0.8 X 16, TPNHMSSS
26 8.613-733.0 WASHER, M5 SHPRF STL ZNPLT
27 8.613-664.0 SCREW, M8-1.25 X 20 HHMS ZNPLT
28 8.601-081.0 WASHER, 1/4 FNDR SS
29 8.601-067.0 WASHER, 5/16 FLT SS
30 8.601-063.0 WASHER, 1/4 SS
31 8.600-861.0 Flanged bearing PRESS STEEL
32 8.600-581.0 NUT, 1/4-20 HEX NYLOCK SS
33 8.600-103.0 BEARING, 3/4 SPH BALL
Valid on 28.09.2018
Quantity Unit
1.000 ST
1.000 ST
1.000 ST
1.000 ST
1.000 ST
2.000 ST
1.000 ST
1.000 ST
1.000 ST
1.000 ST
2.000 ST
1.000 ST
1.000 ST
1.000 ST
2.000 ST
1.000 ST
2.000 ST
2.000 ST
4.000 ST
1.000 ST
1.000 ST
4.000 ST
4.000 ST
1.000 ST
8.000 ST
8.000 ST
2.000 ST
1.000 ST
4.000 ST
6.000 ST
4.000 ST
1.000 ST
2.000 ST
Page 22 / 98
Serial number from Serial number to
6